Structural Engineering and Mechanics

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

The behavior of adhesive joints affected by the geometry and stacking sequence of composite materials

  • Received : 2023.05.15
  • Accepted : 2023.12.08
  • Published : 2023.12.25
⟨ Previous Next ⟩

Abstract

The objective of this study is to investigate the distribution of von Mises stress, peeling stress, and shear stress in the adhesive layer used to bond two composite panels, considering various parameters using a three-dimensional finite element method. The stiffness of the materials and the effect of the stacking order on the amount of load transferred to the adhesive layer were examined to determine which type of laminate generates less stress at the bond line. The study analyzed six different stacking sequences, all with a common first layer in contact with the adhesive and a 0° orientation. Additionally, the impact of using hybrid composites on reducing bond line stress was investigated.

Keywords

References

  1. ABAQUS finite Element Programs, ABAQUS iStandard 5.6, Hibbitt, Pawtucket, RI 028, Karlsson and Sorensen, Inc.
  2. Akpinar, S. (2013), "Effects of laminate carbon/epoxy composite patches on the strength of double-strap adhesive joints: Experimental and numerical analysis", Mater. Des., 51, 501-512. https://doi.org/10.1016/j.matdes.2013.04.037.
  3. Aydin, M.D. (2008), "3-D nonlinear stress analysis on adhesively bonded single lap composite joints with different ply stacking sequences", J. Adhes., 84(1), 15-36. https://doi.org/10.1080/00218460801888359.
  4. Budhe, S., Banea, M.D., De Barros, S. and Da Silva, L.F.M. (2017), "An updated review of adhesively bonded joints in composite materials", Int. J. Adhes. Adhesiv., 72, 30-42. https://doi.org/10.1016/j.ijadhadh.2016.10.010.
  5. Campilho, R.D.S.G., De Moura, M.F.S.F. and Domingues, J.J.M.S. (2005), "Modelling single anddouble-lap repairs on composite materials", Compos. Sci. Technol., 65, 1948-1958. https://doi.org/10.1016/j.compscitech.2005.04.007.
  6. Demiral, M. and Kadioglu, F. (2018), "Failure behaviour of the adhesive layer and angle ply composite adherends in single lap joints: A numerical study", Int. J. Adhes. Adhesiv., 87, 181-190. https://doi.org/10.1016/j.ijadhadh.2018.10.010.
  7. Demoura, M., Goncalves, J., Chousal, J. and Campilho, R. (2008), "Cohesive and continuum mixed-mode damage models applied to the simulation of the mechanical behaviour of bonded joints", Int. J. Adhes. Adhesiv., 28, 419426. https://doi.org/10.1016/j.ijadhadh.2008.04.004.
  8. Fathi, P., Oskouei, A.N., Vahedi, K. and Petrudi, A.M. (2020), "Numerical and experimental analysis of stacking sequences effects in composite mechanical joints under impact loadings", Frattura ed Integrita Strutturale, 53, 457-473. https://doi.org/10.3221/IGF-ESIS.53.36.
  9. Fayyadh, M.M. and Razak, H.A. (2022), "The effect of CFRP-concrete bond mechanism on dynamic parameters of repaired concrete girders", Struct. Eng. Mech., 82(3), 343-354. https://doi.org/10.12989/sem.2022.82.3.343.
  10. Feng, N.L., Malingam, S.D. and Irulappasamy, S. (2019), "Bolted joint behavior of hybrid composites. In failure analysis in biocomposites, fibre-reinforced composites and hybrid composites", Woodhead Publishing, 79-95.
  11. Karimpour, H. and Mazloom, M. (2022), "Pseudo-strain hardening and mechanical properties of green cementitious composites containing polypropylene fibers", Struct. Eng. Mech., 81(5), 575-589. https://doi.org/10.12989/sem.2022.81.5.575.
  12. Kim, T.H., Kweon, J.H. and Choi, J.H. (2008), "An experimental study on the effect of overlap length on the failure of composite-to-aluminum single-lap bonded joints", J. Reinf. Plast. Compos., 27(10), 1071-1081. https://doi.org/10.1177/0731684407087.
  13. Li, X., Wang, L., Zhao, W., Wu, H. and Xu, B. (2022), "Selection and analysis of optimum stacking sequence and geometry dimensions on bismaleimides composite joints under tensile loading", Polym. Test., 105, 107421. https://doi.org/10.1016/j.polymertesting.2021.107421.
  14. Liao, Q., Guo, Z.W., Duan, X.Z., Yu, J.T., Liu, K.K. and Dong, F.Y. (2021), "Mechanical behavior and chloride resistance of cementitious composites with PE and steel fiber", Adv. Concrete Constr., 12(6), 451-459. https://doi.org/10.12989/acc.2021.12.6.451.
  15. Mahdavi, S., Shaterzadeh, A.R. and Jafari, M. (2021), "Optimum design for thermal buckling of composite plates with semi triangular cutout using PSO algorithm", Struct. Eng. Mech., 80(1), 83-90. https://doi.org/10.12989/sem.2021.80.1.083.
  16. Marzi, S., Villalonga, L., Politer, M. and Kleiner, F. (2008). "Usage of cohesive elements in crash analysis of large bonded vehicle structures", LS-DYNA Anwenderforum Bamberg.
  17. Moulgada, A., Zagane, M.E.S., Abderrahmane, S. and Zahi, R. (2021), "Study of mechanical behavior by fatigue of a cracked plate repaired by different composite patches", Fratturaed Integrita Strutturale, 15(56), 195-202. https://doi.org/10.3221/IGF-ESIS.56.16
  18. Ozel, A., Yazici, B., Akpinar, S., Aydin, M.D. and Temiz, S. (2014), "A study on the strength of adhesively bonded joints with different adherends", Compos. Part B: Eng., 62, 167-174. https://doi.org/10.1016/j.compositesb.2014.03.001.
  19. Purimpat, S., Jerome, R. and Shahram, A. (2013), "Effect of fiber angle orientation on a laminated composite single-lap adhesive joint", Adv. Compos. Mater., 22(3), 139-149. https://doi.org/10.1080/09243046.2013.782805.
  20. Queiroz, H.F. and Banea, M.D. (2022), "Methods to increase the mechanical performance of composite adhesive joints: An overview with focus on joints with natural fibre composite adherends", Adv. Compos. Mater., 56(26), 3993-4010. https://doi.org/10.1177/00219983221125.
  21. Rachid, Z., Kaddour, R. and Achache, H. (2018), "Dynamic calculation of a tapered shaft rotor made of composite material", Adv. Aircraft Spacecraft Sci., 5(1), 51. https://doi.org/10.12989/aas.2018.5.1.051.
  22. Sayman, O., Ozel, A., Pasinli, A. and Ozen, M. (2013), "Nonlinear stress analysis in adhesively bonded single-lap joint", J. Adhes. Sci. Technol., 27(21), 2304-2314. https://doi.org/10.1080/01694243.2013.773696.
  23. Shishesaz, M. and Hosseini, M. (2018), "Effects of joint geometry and material on stress distribution, strength and failure of bonded composite joints: An overview", J. Adhes., 96(12), https://doi.org/10.1080/00218464.2018.1554483.
  24. Zahi, R., Sahli, A., Kaci, D., Bourada, F., Tounsi, A. and Ghazwani, M.H. (2023), "Study and analysis of a tapered shaft in composite materials with variable speed of rotation", Struct. Eng. Mech., 87(2), 191-200. https://doi.org/10.12989/sem.2023.87.2.191.
  25. Zhang, Q., Cheng, X., Cheng, Y., Li, W. and Hu, R. (2019), "Investigation of tensile behavior and influence factors of composite-to-metal 2D-scarf bonded joint", Eng. Struct., 180, 284-294. https://doi.org/10.1016/j.engstruct.2018.11.036.