Steel and Composite Structures

  • 제43권5호
  • /
  • Pages.523-532
  • /
  • 2022
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Performance and heat transfer analysis of turbochargers using numerical and experimental methods

  • Pakbin, Ali (Department of Mechanical Engineering, Kashan Branch, Islamic Azad University) ;
  • Tabatabaei, Hamidreza (Department of Mechanical Engineering, Kashan Branch, Islamic Azad University) ;
  • Nouri-Bidgoli, Hossein (Department of Mechanical Engineering, Kashan Branch, Islamic Azad University)
  • 투고 : 2020.01.23
  • 심사 : 2022.04.18
  • 발행 : 2022.06.10
⟨ 이전 논문 다음 논문 ⟩

초록

Turbocharger technology is one of the ways to survive in a competitive market that is facing increasing demand for fuel and improving the efficiency of vehicle engines. Turbocharging allows the engine to operate at close to its maximum power, thereby reducing the relative friction losses. One way to optimally understand the behavior of a turbocharger is to better understand the heat flow. In this paper, a 1.7 liter, 4 cylinder and 16 air valve gasoline engine turbocharger with compressible, viscous and 3D flow was investigated. The purpose of this paper is numerical investigation of the number of heat transfer in gasoline engines turbochargers under 3D flow and to examine the effect of different types of coatings on its performance; To do this, modeling of snail chamber and turbine blades in CATIA and simulation in ANSYS-FLUENT software have been used to compare the results of turbine with experimental results in both adiabatic and non-adiabatic (heat transfer) conditions. It should be noted that the turbine blades are modeled using multiple rotational coordinate methods. In the experimental section, we simulated our model without coating in two states of adiabatic and non-adiabatic. Then we matched our results with the experimental results to prove the validation of the model. Comparison of numerical and experimental results showed a difference of 8-10%, which indicates the accuracy and precision of numerical results. Also, in our studies, we concluded that the highest effective power of the turbocharged engine is achieved in the adiabatic state. We also used three types of SiO2, Sic and Si3N4 ceramic coatings to investigate the effect of insulating coatings on turbine shells to prevent heat transfer. The results showed that SiO2 has better results than the other two coatings due to its lower heat transfer coefficient.

키워드

과제정보

We thank the Faculty of Mechanical Engineering of Kashan Azad University for cooperating and providing equipment related to the laboratory.

참고문헌

  1. Abbas, M.R., Uday, M.B., Noor, A.M., Ahmad, N. and Rajoo, S. (2016), "Microstructural evaluation of a slurry based Ni/YSZ thermal barrier coating for automotive turbocharger turbine application", Mat. Design, 109, 47-56, https://doi.org/10.1016/j.matdes.2016.07.070.
  2. Aghaali, H., Angstrom, H. and Serrano Cruz, J.R. (2015), "Evaluation of different heat transfer conditions on an automotive turbocharger", Int. J. Eng. Res., 16(2), 137-151, https://doi.org/10.1177/1468087414524755.
  3. Burke, R.D., Copeland, C.D, Duda, T. and Rayes-Belmonte, M.A. (2016), "Lumped capacitance and three-dimensional computational fluid dynamics conjugate heat transfer modelingof an automotive turbocharger", J. Eng. Gas Turb. Power, 138, 092602. https://doi.org/10.1115/1.4032663.
  4. Chen, D., Chu, Z.M. and Zhang, Q. (2013), "Analysis of several test methods about heat insulation capabilities of ceramic thermal barrier coatings", Phys. Proced., 50, 248-52, https://doi.org/10.1016/j.phpro.2013.11.039.
  5. Diaz, P.M. (2017), "Efficiency of nano ceramic coated and turbocharged internal combustion engine-A review", J. Adv. Mech. Eng. Sci., 3(1). 1-3. https://doi.org/10.18831/james.in/2017011001.
  6. Dimelow, A. (2018), "Transient conjugate heat transfer analysis of a turbocharger", Cummins Turbo Techn., 22, 132-144. https://doi.org/10.2514/6.2006-3264.
  7. Gier, T.S., Biesinger, T. and Eickenbusch, H. (2018), "Heat Transfer Coefficients in a Turbocharger With and Without Boiling", Universitatsbibliothek der RWTH Aachen.
  8. Han, F., Mao, Y. and Tan, J. (2016), "Influences of flow loss and inlet distortions from radial inlets on the performances of centrifugal compressor stages", J. Mech. Sci. Technol., 10, 4591-4599. https://doi.org/10.1007/s12206-016-0930-y.
  9. Huang, L., Ma, C., Li, Y., Gao, J. and Qi, M. (2019), "Applying neural networks (NN) to the improvement of gasoline turbocharger heat transfer modeling", Appl. Therm. Eng., 141, 1080-1091. https://doi.org/10.1016/j.applthermaleng.2018.06.062.
  10. Jiaqiang, E., Zhang, Zh., Tu, Zh., Zuo, W., Hu, W., Han, D. and Jin, Y. (2018), "Effect analysis on flow and boiling heat transfer performance of cooling water-jacket of bearing in the gasoline engine turbocharger", Appl. Therm. Eng., 130, 754-766, https://doi.org/10.1016/j.applthermaleng.2017.11.070.
  11. Lata, P. and Kaur. (2021), "Interactions in a homogeneous isotropic modified couple stress thermoelastic solid with multidual- phase-lag heat transfer and two temperature", Steel Compos. Struct., 38, 213-221. http://dx.doi.org/10.12989/scs.2021.38.2.213.
  12. Lata, P. and Singh, K. (2021), "Stoneley wave propagation in nonlocal isotropic magneto-thermoelastic solid with multi-dualphase lag heat transfer", Steel Compos. Struct., 38, 141-150. http://dx.doi.org/10.12989/scs.2021.38.2.141.
  13. Lata, P., Kaur, I. and Singh, K. (2020), "Transversely isotropic thin circular plate with multi-dual-phase lag heat transfer", Steel Compos. Struct., 35, 341-351. http://dx.doi.org/10.12989/scs.2020.35.3.343.
  14. Launder, B.E. and Spalding, B. (1974), "The numerical computation of turbulent flows", Comput. Methods Appl. Mech. Eng., 3, 269-289. https://doi.org/10.1016/0045-7825(74)90029-2.
  15. Marelli, S., Marmorato, G. and Capobianco, M. (2016), "Evaluation of heat transfer eects in small turbochargers by theoretical model and its experimental validation", Energy, 112, 264-272, https://doi.org/10.1016/j.energy.2016.06.067.
  16. Savic, B., Gao, X. and Baar, R. (2018), "Turbocharger heat transfer determination with a power based phenomenological approach and a CHT validation", J. Turbomach., 33, 544-551. https://doi.org/10.1115/1.4041806.
  17. Schinner, M., Seume, J., Ehrhard, J. and Bogner, M. (2017), "Heat transfer correction methods for turbocharger performance measurements", J. Eng. Gas Turb. Power, 139, 022602-1. https://doi.org/10.1115/1.4034234.
  18. Serrano, J.R., Olmeda, P., Arnau, F.J. and Reyes-Belmonte, M.A. (2015), "A study on the internal convection in small turbochargers. pro-posal of heat transfer convective coeycients", Appl. Therm. Energ., 89, 587-599. https://doi.org/10.1177/1468087419834194.
  19. Serrano, J.R., Olmeda, P., Arnau, F.J., Dombrovsky, A. and Smith, L. (2018), "Analysis and methodology to characterize heat transfer phenomena in automotive turbochargers", J. Eng. Gas Turb. Power, 137, 021901-1. https://doi.org/10.1115/1.4028261.
  20. Sirakov, B. and Casey, M. (2013), "Evaluation of heat transfer effects on turbocharger performance", J. Turbomach., 135, 233- 238. https://doi.org/10. 1115/1.4006608. https://doi.org/10.1115/1.4006608
  21. Storck, K., Karlsson, M., Andersson, I., Renner, J. and Loyd, D. (2012), "Formelsamling i termo-och fluiddynamik", LiU-tryck.
  22. Zheng, X., Yun, L. and Sun, Z. (2016), "Effects of volute's asymmetry on the performance of a turbocharger centrifugal compressor", Proceed. Inst. Mech. Eng., Part G, 232, 1235-1246, https://doi.org/10.1177/0954410016670418.