Earthquakes and Structures

  • 제22권2호
  • /
  • Pages.185-201
  • /
  • 2022
  • /
  • 2092-7614(pISSN)
  • /
  • 2092-7622(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Health assessment of RC building subjected to ambient excitation : Strategy and application

  • Mehboob, Saqib (Department of Civil Engineering, University of Engineering and Technology Taxila) ;
  • Khan, Qaiser Uz Zaman (Department of Civil Engineering, University of Engineering and Technology Taxila) ;
  • Ahmad, Sohaib (Works and Services Organization) ;
  • Anwar, Syed M. (Department of Software Engineering, University of Engineering and Technology Taxila)
  • 투고 : 2021.04.15
  • 심사 : 2022.01.18
  • 발행 : 2022.02.25
⟨ 이전 논문 다음 논문 ⟩

초록

Structural Health Monitoring (SHM) is used to provide reliable information about the structure's integrity in near realtime following extreme incidents such as earthquakes, considering the inevitable aging and degradation that occurs in operating environments. This paper experimentally investigates an integrated wireless sensor network (Wi-SN) based monitoring technique for damage detection in concrete structures. An effective SHM technique can be used to detect potential structural damage based on post-earthquake data. Two novel methods are proposed for damage detection in reinforced concrete (RC) building structures including: (i) Jerk Energy Method (JEM), which is based on time-domain analysis, and (ii) Modal Contributing Parameter (MCP), which is based on frequency-domain analysis. Wireless accelerometer sensors are installed at each story level to monitor the dynamic responses from the building structure. Prior knowledge of the initial state (immediately after construction) of the structure is not required in these methods. Proposed methods only use responses recorded during ambient vibration state (i.e., operational state) to estimate the damage index. Herein, the experimental studies serve as an illustration of the procedures. In particular, (i) a 3-story shear-type steel frame model is analyzed for several damage scenarios and (ii) 2-story RC scaled down (at 1/6th) building models, simulated and verified under experimental tests on a shaking table. As a result, in addition to the usual benefits like system adaptability, and cost-effectiveness, the proposed sensing system does not require a cluster of sensors. The spatial information in the real-time recorded data is used in global damage identification stage of SHM. Whereas in next stage of SHM, the damage is detected at the story level. Experimental results also show the efficiency and superior performance of the proposed measuring techniques.

키워드

과제정보

The research described in this paper was financially supported by the Higher Education Commission (HEC) Pakistan under the National Research Program for Universities (NRPU) with Project ID 3820.

참고문헌

  1. Abdulkarem, M., Samsudin, K., Rokhani, F.Z. and Rasid, M.F. (2020), "Wireless sensor network for structural health monitoring: A contemporary review of technologies, challenges, and future direction", Struct. Health Monit., 19(3), 693-735. https://doi.org/10.1177/1475921719854528.
  2. Ali, M.R. and Okabayashi, T. (2011), "System identification of highway bridges from ambient vibration using subspace stochastic realization theories", Earthq. Struct., 2(2), 189-206. https://doi.org/10.12989/eas.2011.2.2.189.
  3. Allemang, R.J. (1982), "A correlation coefficient for modal vector analysis", Proceedings of the 1st International Modal Analysis Conference, 110-116.
  4. Alvandi, A. and Cremona, C. (2006), "Assessment of vibration-based damage identification techniques", J. Sound Vib., 292(1-2), 179-202. https://doi.org/10.1016/j.jsv.2005.07.036.
  5. Amezquita-Sanchez, J.P. and Adeli, H. (2016), "Signal processing techniques for vibration-based health monitoring of smart structures", Archives Comput. Meth. Eng., 23(1), 1-15. https://doi.org/10.1007/s11831-014-9135-7.
  6. Andersen, E. and Pedersen, L. (1994), "Structural monitoring of the great belt east bridge", Symposium on Strait Crossings.
  7. Aygun, B. and Gungor, V.C. (2011), "Wireless sensor networks for structure health monitoring: Recent advances and future research directions", Sensor Rev., 31(3), 261-276. https://doi.org/10.1108/02602281111140038.
  8. Bagherahmadi, S.A. and Seyedpoor, S.M. (2018), "Structural damage detection using a damage probability index based on frequency response function and strain energy concept", Struct. Eng. Mech., 67(4), 327-336. http://dx.doi.org/10.12989/sem.2018.67.4.327.
  9. Bakir, P.G. (2012), "Instrumentation and system identification of a typical school building in Istanbul", Struct. Eng. Mech., 43(2), 179-197. https://doi.org/10.12989/sem.2012.43.2.179.
  10. Bhuiyan, M.Z.A., Wu, J., Wang, G., Cao, J., Jiang, W. and Atiquzzaman, M. (2017), "Towards cyber-physical systems design for structural health monitoring: Hurdles and opportunities", ACM Transactions Cyber Phys. Syst., 1(4), 1-26. https://doi.org/10.1145/3086508.
  11. Bisht, S.S. and Singh, M.P. (2012), "Detecting sudden changes in stiffness using high-pass filters", Struct. Health Monit., 19(3), 319-331. https://doi.org/10.1002/stc.433.
  12. Bulajic, B.D., Todorovska, M.I., Manic, M.I. and Trifunac, M.D. (2020), "Structural health monitoring study of the ZOIL building using earthquake records", Soil Dynam. Earthq. Eng., 133, 106105. https://doi.org/10.1016/j.soildyn.2020.106105.
  13. Cabboi, A., Magalhaes, F., Gentile, C. and Cunha, A. (2017), "Automated modal identification and tracking: Application to an iron arch bridge", Struct. Health Monit., 24(1), e1854. https://doi.org/10.1002/stc.1854.
  14. Caetano, E., Cunha, A., Magalhaes, F. and Moutinho, C. (2010), "Studies for controlling human-induced vibration of the Pedro e Ines footbridge, Portugal. Part 1: Assessment of dynamic behaviour", Eng. Struct., 32(4), 1069-1081. https://doi.org/10.1016/j.engstruct.2009.12.034.
  15. Caetano, E., Cunha, A., Moutinho, C. and Magalhaes, F. (2010), "Studies for controlling human-induced vibration of the Pedro e Ines footbridge, Portugal. Part 2: Implementation of tuned mass dampers", Eng. Struct., 32(4), 1082-1091. https://doi.org/10.1016/j.engstruct.2009.12.033.
  16. Capecchi, D. and Vestroni, F. (1999), "Monitoring of structural systems by using frequency data", Earthq. Eng. Struct. Dynam., 28(5), 447-461. https://doi.org/10.1002/(SICI)1096-9845(199905)28:5<447::AID-EQE812>3.0.CO;2-2.
  17. Cara, F.J., Carpio, J., Juan, J. and Alarcon, E. (2012), "An approach to operational modal analysis using the expectation maximization algorithm", Mech. Syst. Signal Pr., 31, 109-129. https://doi.org/10.1016/j.ymssp.2012.04.004.
  18. Cawley, P. and Adams, R.D. (1979), "The location of defects in structures from measurements of natural frequencies", J. Strain Anal. Eng. Des., 14(2), 49-57. https://doi.org/10.1243/03093247V142049.
  19. Ceylan, H., Yavas, S., Dong, L., Jiao, Y., Yang, S., Kim, S., Gopalakrishnan, K. and Taylor, P. (2016), "Development of a wireless MEMS multifunction sensor system and field demonstration of embedded sensors for monitoring concrete pavements, Volume I", InTrans Project Reports, Iowa State University, Institute for Transportation, U.S.A.
  20. Chalioris, C.E., Voutetaki, M.E. and Liolios, A.A. (2020), "Structural health monitoring of seismically vulnerable RC frames under lateral cyclic loading", Earthq. Struct., 19(1), 29-44. https://doi.org/10.12989/eas.2020.19.1.29.
  21. Deraemaeker, A., Reynders, E., De Roeck, G. and Kullaa, J. (2008), "Vibration-based structural health monitoring using output-only measurements under changing environment", Mech. Syst. Signal Pr., 22(1), 34-56. https://doi.org/10.1016/j.ymssp.2007.07.004.
  22. Devriendt, C., Magalhaes, F., Weijtjens, W., De Sitter, G., Cunha, A. and Guillaume, P. (2014), "Structural health monitoring of offshore wind turbines using automated operational modal analysis", Struct. Health Monit., 13(6), 644-659. https://doi.org/10.1177/1475921714556568.
  23. Dinh-Cong, D., Nguyen-Thoi, T. and Nguyen, D.T. (2020), "A FE model updating technique based on SAP2000-OAPI and enhanced SOS algorithm for damage assessment of full-scale structures", Appl. Soft Comput., 89, 106100. https://doi.org/10.1016/j.asoc.2020.106100.
  24. Dinh, H., Nagayama, T. and Fujino, Y. (2012), "Structural parameter identification by use of additional known masses and its experimental application", Struct. Health Monit., 19(3), 436-450. https://doi.org/10.1002/stc.444.
  25. Doebling, S.W., Farrar, C.R. and Prime, M.B. (1998), "A summary review of vibration-based damage identification methods", Shock Vib., 30(2), 91-105. https://doi.org/10.1177/058310249803000201
  26. Doebling, S.W., Farrar, C.R., Prime, M.B. and Shevitz, D.W. (1996), "Damage identification and health monitoring of structural and mechanical systems from changes in their vibration characteristics: A literature review", LA-13070-MS, Los Alamos National Lab. https://doi.org/10.2172/249299.
  27. Domaneschi, M., Sigurdardottir, D. and Glisic, B. (2017), "Damage detection on output-only monitoring of dynamic curvature in composite decks", Struct. Monit. Maint., 4(1), 1-15. https://doi.org/10.12989/smm.2017.4.1.001.
  28. Fan, W. and Qiao, P. (2011), "Vibration-based damage identification methods: a review and comparative study", Struct. Health Monit., 10(1), 83-111. https://doi.org/10.1177/1475921710365419.
  29. Farrar, C.R. and Worden, K. (2010), "An introduction to structural health monitoring", New Trends Vib. Based Struct. Health Monit., 1-17. https://doi.org/10.1098/rsta.2006.1928.
  30. Frigui, F., Faye, J.P., Martin, C., Dalverny, O., Peres, F. and Judenherc, S. (2018), "Global methodology for damage detection and localization in civil engineering structures", Eng. Struct., 171, 686-695. https://doi.org/10.1016/j.engstruct.2018.06.026.
  31. Garcia-Palencia, A., Santini-Bell, E., Gul, M. and Catbas, N. (2015), "A FRF-based algorithm for damage detection using experimentally collected data", Struct. Monit. Maint., 2(4), 399-418. http://dx.doi.org/10.12989/smm.2015.2.4.399.
  32. Gentile, C., Guidobaldi, M. and Saisi, A. (2016), "One-year dynamic monitoring of a historic tower: Damage detection under changing environment", Meccanica, 51(11), 2873-2889. https://doi.org/10.1007/s11012-016-0482-3.
  33. Ghannadi, P. and Kourehli, S.S. (2019), "Model updating and damage detection in multi-story shear frames using Salp swarm algorithm", Earthq. Struct., 17(1), 63-73. https://doi.org/10.12989/eas.2019.17.1.063.
  34. Gillich, G.R. and Praisach, Z.I. (2012), "Robust method to identify damages in beams based on frequency shift analysis", Health Monit. Struct. Biologic. Syst. 8348, 367-378.
  35. Guo, Y., Kwon, D.K. and Kareem, A. (2016), "Near-real-time hybrid system identification framework for civil structures with application to Burj Khalifa", J. Struct. Eng., 142(2), 04015132. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001402.
  36. Harris, H.G. and Sabnis, G. (1999), Structural Modeling and Experimental Techniques, CRC press.
  37. Hipley, P. (2001), "Caltrans' current state-of-practice", Proceedings of the Instrumental Systems for Diagnostics Seismic Response of Bridges Dams, 3-7.
  38. Homaei, F., Shojaee, S. and Amiri, G.G. (2014), "A direct damage detection method using multiple damage localization index based on mode shapes criterion", Struct. Eng. Mech., 49(2), 183-202. https://doi.org/10.12989/sem.2014.49.2.183.
  39. Hu, W.H., Caetano, E. and Cunha, A. (2013), "Structural health monitoring of a stress-ribbon footbridge", Eng. Struct., 57, 578-593. https://doi.org/10.1016/j.engstruct.2012.06.051.
  40. Iacovino, C., Ditommaso, R., Ponzo, F. and Limongelli, M. (2018), "The interpolation evolution method for damage localization in structures under seismic excitation", Earthq. Eng. Struct. Dynam., 47(10), 2117-2136. https://doi.org/10.1002/eqe.3062.
  41. Kilic, G. (2014), "Wireless sensor network protocol comparison for bridge health assessment", Struct. Eng. Mech., 49(4), 509-521. https://doi.org/10.12989/sem.2014.49.4.509.
  42. Kim, J.T., Ryu, Y.S., Cho, H.M. and Stubbs, N. (2003), "Damage identification in beam-type structures: Frequency-based method vs mode-shape-based method", Eng. Struct., 25(1), 57-67. https://doi.org/10.1016/S0141-0296(02)00118-9.
  43. Kim, J.T. and Stubbs, N. (2002), "Improved damage identification method based on modal information", J. Sound Vib., 252(2), 223-238. https://doi.org/10.1006/jsvi.2001.3749.
  44. Kim, J.T. and Stubbs, N. (2003), "Crack detection in beam-type structures using frequency data", J. Sound Vib., 259(1), 145-160. https://doi.org/10.1006/jsvi.2002.5132
  45. Le, T.P. and Paultre, P. (2012), "Modal identification based on continuous wavelet transform and ambient excitation tests", J. Sound Vib., 331(9), 2023-2037. https://doi.org/10.1002/stc.1622.
  46. Li, Q., Zhi, L., Yi, J., To, A. and Xie, J. (2014), "Monitoring of typhoon effects on a super-tall building in Hong Kong", Struct. Health Monit., 21(6), 926-949. https://doi.org/10.1002/stc.1622.
  47. Li, Y. and Chen, Y. (2013), "A review on recent development of vibration-based structural robust damage detection", Struct. Eng. Mech., 45(2), 159-168. https://doi.org/10.12989/sem.2013.45.2.159.
  48. Libelium (2017), http://libelium.com/development/waspmote/documentation/waspmote-technicalguide.
  49. Liu, H., Yu, L., Luo, Z. and Chen, Z. (2020), "Multi-strategy structural damage detection based on included angle of vectors and sparse regularization", Struct. Eng. Mech., 75(4), 415-424. https://doi.org/10.12989/sem.2020.75.4.415.
  50. Lynch, J.P. (2007), "An overview of wireless structural health monitoring for civil structures", Philos. T. R. Soc. A, 365(1851), 345-372. https://doi.org/10.1098/rsta.2006.1932.
  51. Lynch, J.P. and Loh, K.J. (2006), "A summary review of wireless sensors and sensor networks for structural health monitoring", Shock Vib., 38(2), 91-130. https://doi.org/10.1177/0583102406061499.
  52. Magalhaes, F., Cunha, A. and Caetano, E. (2012), "Vibration based structural health monitoring of an arch bridge: from automated OMA to damage detection", Mech. Syst. Signal Pr., 28, 212-228. https://doi.org/10.1016/j.ymssp.2011.06.011.
  53. Martins, N., Caetano, E., Diord, S., Magalhaes, F. and Cunha, A. (2014), "Dynamic monitoring of a stadium suspension roof: Wind and temperature influence on modal parameters and structural response", Eng. Struct., 59, 80-94. https://doi.org/10.1016/j.engstruct.2013.10.021.
  54. Mehboob, S., Zamana, Q.U. and Ahmad, S. (2020), "Numerical study for evaluation of a vibration based damage index for effective damage detection", B. Polish Acad. Sci. Tech. Sci., 1443-1456. https://doi.org/10.24425/bpasts.2020.134651.
  55. Mehboob, S. and Zamana, Q.U. (2021), "Vibration-based method for story-level damage detection of the reinforced concrete structure", Comput. Concrete, 27(1), 29-39. https://doi.org/10.12989/cac.2021.27.1.029.
  56. Mei, Q., Gul, M. and Boay, M. (2019), "Indirect health monitoring of bridges using Mel-frequency cepstral coefficients and principal component analysis", Mech. Syst. Signal Pr., 119, 523-546. https://doi.org/10.1016/j.ymssp.2018.10.006.
  57. Mousavi, Z., Ettefagh, M.M., Sadeghi, M.H. and Razavi, S.N. (2020), "Developing deep neural network for damage detection of beam-like structures using dynamic response based on FE model and real healthy state", Appl. Acoust., 168, 107402. https://doi.org/10.1016/j.apacoust.2020.107402.
  58. Mufti, A.A. (2002), "Structural health monitoring of innovative Canadian civil engineering structures", Struct. Health Monit., 1(1), 89-103. https://doi.org/10.1177%2F147592170200100106. https://doi.org/10.1177%2F147592170200100106
  59. Nguyen, D.H., Nguyen, Q.B., Bui-Tien, T., De Roeck, G. and Wahab, M.A. (2020), "Damage detection in girder bridges using modal curvatures gapped smoothing method and convolutional neural network: Application to Bo Nghi bridge", Theor. Appl. Fract. Mec., 109, 102728. https://doi.org/10.1016/j.tafmec.2020.102728.
  60. Oliveira, G., Magalhaes, F., Cunha, A. and Caetano, E. (2016), "Development and implementation of a continuous dynamic monitoring system in a wind turbine", J. Civil Struct. Health Monit., 6(3), 343-353. https://doi.org/10.1007/s13349-016-0182-7.
  61. Omrani, R., Hudson, R.E. and Taciroglu, E. (2012), "Story-by- story estimation of the stiffness parameters of laterally- torsionally coupled buildings using forced or ambient vibration data: I. Formulation and verification", Earthq. Eng. Struct. Dynam., 41(12), 1609-1634. https://doi.org/10.1002/eqe.1192.
  62. Ou, J. (2004), "The state-of-the-art and application of intelligent health monitoring systems for civil infrastructures in mainland of China", Prog. Struct. Eng. Mech. Comput., 599-608.
  63. Pai, P.F. and Young, L.G. (2001), "Damage detection of beams using operational deflection shapes", Int. J. Solids Struct., 38(18), 3161-3192. https://doi.org/10.1016/S0020-7683(00)00274-2.
  64. Pedram, M., Esfandiari, A. and Khedmati, M.R. (2017), "Damage detection by a FE model updating method using power spectral density: numerical and experimental investigation", J. Sound Vib., 397, 51-76. https://doi.org/10.1016/j.jsv.2017.02.052.
  65. Pentaris, F., Stonham, J. and Makris, J. (2014), "A cost effective wireless structural health monitoring network for buildings in earthquake zones", Smart Mater. Struct., 23(10), 105010. https://doi.org/10.1088/0964-1726/23/10/105010.
  66. Pines, D. and Aktan, A.E. (2002), "Status of structural health monitoring of long-span bridges in the United States", Prog. Struct. Eng. Mater., 4(4), 372-380. https://doi.org/10.1002/pse.129.
  67. Porcu, M., Patteri, D., Melis, S. and Aymerich, F. (2019), "Effectiveness of the FRF curvature technique for structural health monitoring", Constr. Build. Mater., 226, 173-187. https://doi.org/10.1016/j.conbuildmat.2019.07.123.
  68. Providakis, C., Stefanaki, K., Voutetaki, M., Tsompanakis, J. and Stavroulaki, M. (2014), "A near and far-field monitoring technique for damage detection in concrete structures", Struct. Monit. Maint., 1(2), 159-171. https://doi.org/10.12989/smm.2014.1.2.159.
  69. Rainieri, C. and Fabbrocino, G. (2014), Operational Modal Analysis of Civil Engineering Structures, Springer, New York, 142, 143. https://doi.org/10.1007/978-1-4939-0767-0.
  70. Rajaravivarma, V., Yang, Y. and Yang, T. (2003), "An overview of wireless sensor network and applications", Proceedings of the 35th Southeastern Symposium on System Theory, Morgantown, March.
  71. Salawu, O. (1997), "Detection of structural damage through changes in frequency: a review", Eng. Struct., 19(9), 718-723. https://doi.org/10.1016/S0141-0296(96)00149-6.
  72. Silicon-Laboratories-Inc. (2013), Evolution of wireless sensor networks, Report Rev. 1.0. https://www.silabs.com/whitepapers?query=wireless.
  73. Sohn, H., Farrar, C.R., Hemez, F.M., Shunk, D.D., Stinemates, D.W., Nadler, B.R. and Czarnecki, J.J. (2003), "A review of structural health monitoring literature: 1996-2001", Los Alamos National Laboratory, U.S.A.
  74. Stoykov, S. and Manoach, E. (2021), "Damage localization of beams based on measured forced responses", Mech. Syst. Signal Pr., 151, 107379. https://doi.org/10.1016/j.ymssp.2020.107379.
  75. Tamura, Y. and Suganuma, S.Y. (1996), "Evaluation of amplitude-dependent damping and natural frequency of buildings during strong winds", J. Wind Eng. Industrial Aerod., 59(2-3), 115-130. https://doi.org/10.1016/0167-6105(96)00003-7.
  76. Todorovska, M.I. (2009), "Seismic interferometry of a soil-structure interaction model with coupled horizontal and rocking response", B. Seismol. Soc. Am., 99(2A), 611-625. https://doi.org/10.1785/0120080191
  77. Topole, K.G. and Stubbs, N. (1995), "Non-destructive damage evaluation of a structure from limited modal parameters", Earthq. Eng. Struct. Dynam., 24(11), 1427-1436. https://doi.org/10.1002/eqe.4290241102.
  78. Torbol, M., Kim, S. and Chou, P. (2013), "Remote structural health monitoring systems for next generation SCADA", Smart Struct. Syst., 11(5), 511-531. https://doi.org/10.12989/sss.2013.11.5.511.
  79. Trifunac, M.D., Todorovska, M.I., Manic, M.I. and Bulajic, B.D. (2010), "Variability of the fixed-base and soil-structure system frequencies of a building-The case of Borik-2 building", Struct. Health Monit., 17(2), 120-151. https://doi.org/10.1002/stc.277.
  80. Ubertini, F., Cavalagli, N., Kita, A. and Comanducci, G. (2018), "Assessment of a monumental masonry bell-tower after 2016 Central Italy seismic sequence by long-term SHM", B. Earthq. Eng., 16(2), 775-801. https://doi.org/10.1007/s10518-017-0222-7.
  81. Vahidi, M., Vahdani, S., Rahimian, M., Jamshidi, N. and Kanee, A.T. (2019), "Evolutionary-base finite element model updating and damage detection using modal testing results", Struct. Eng. Mech., 70(3), 339-350. https://doi.org/10.12989/sem.2019.70.3.339.
  82. Venanzi, I., Kita, A., Cavalagli, N., Ierimonti, L. and Ubertini, F. (2020), "Earthquake-induced damage localization in an historic masonry tower through long-term dynamic monitoring and FE model calibration", B. Earthq. Eng., 18(5), 2247-2274. https://doi.org/10.1007/s10518-019-00780-4.
  83. Wang, H., Mao, J.X. and Xu, Z.D. (2020), "Investigation of dynamic properties of a long-span cable-stayed bridge during typhoon events based on structural health monitoring", J. Wind Eng. Industrial Aerod., 201, 104172. https://doi.org/10.1016/j.jweia.2020.104172.
  84. Wong, K.Y. (2004), "Instrumentation and health monitoring of cable-supported bridges", Struct. Health Monit., 11(2), 91-124. https://doi.org/10.1002/stc.33.
  85. Xia, Y., Hao, H., Brownjohn, J.M. and Xia, P.Q. (2002), "Damage identification of structures with uncertain frequency and mode shape data", Earthq. Eng. Struct. Dynam., 31(5), 1053-1066. https://doi.org/10.1002/eqe.137.
  86. Yan, A.M., Kerschen, G., De Boe, P. and Golinval, J.C. (2005), "Structural damage diagnosis under varying environmental conditions-part I: A linear analysis", Mech. Syst. Signal Pr., 19(4), 847-864. https://doi.org/10.1016/j.ymssp.2004.12.002.
  87. Yan, Y., Cheng, L., Wu, Z. and Yam, L. (2007), "Development in vibration-based structural damage detection technique", Mech. Syst. Signal Pr., 21(5), 2198-2211. https://doi.org/10.1016/j.ymssp.2006.10.002.
  88. Yazdanpanah, O. and Seyedpoor, S. (2015), "A new damage detection indicator for beams based on mode shape data", Struct. Eng. Mech., 53(4), 725-744. https://doi.org/10.12989/sem.2015.53.4.725.
  89. Yi, T.H., Li, H.N. and Gu, M. (2012), "Sensor placement for structural health monitoring of Canton tower", Smart Struct. Syst., 10(4), 313-329. https://doi.org/10.12989/sss.2012.10.4_5.313.
  90. Yin, T., Ng, C.T. and Kotousov, A. (2021), "Damage detection of ultra-high-performance fibre-reinforced concrete using a harmonic wave modulation technique", Constr. Build. Mater., 313, 125306. https://doi.org/10.1016/j.conbuildmat.2021.125306.
  91. Yun, C.B., Lee, J.J., Kim, S.K. and Kim, J.W. (2003), "Recent R&D activities on structural health monitoring for civil infrastructures in Korea", KSCE J. Civil Eng., 7(6), 637-651. https://doi.org/10.1007/BF02829136.
  92. Zhang, L., Wu, G. and Cheng, X. (2020), "A rapid output-only damage detection method for highway bridges under a moving vehicle using long-gauge strain sensing and the fractal dimension", Measurement, 158, 107711. https://doi.org/10.1016/j.measurement.2020.107711.