Acknowledgement
본 연구는 2022년 한국교통대학교 지원을 받아 수행하였음.
References
- Meckley, J. and Edwards, R., "A study on the design and effectiveness of conformal cooling channels in rapid tooling inserts", The Technology Interface Journal, Vol. 10, No.1, 2009.
- Altaf, K., Raghavan, V. R. and Rani, A. M. A., "Comparative thermal analysis of circular and profiled cooling channels for injection mold tools", Journal of Applied Sciences, Vol.11, pp. 2068-2071, 2011. https://doi.org/10.3923/jas.2011.2068.2071
- Park, S., and Kwon, T., "Optimal cooling system design for the injection molding process", Polym. Eng. Sci., Vol.38, pp. 1450-1462, 1998. https://doi.org/10.1002/pen.10316
- Sachs, E., Wylonis, E., Allen, S., Cima, M., and Guo, H., "Production of injection molding tooling with conformal cooling channels using the three dimensional printing process", Polym. Eng. Sci., Vol.40, pp. 1232-1247, 2000. https://doi.org/10.1002/pen.11251
- Shayfull, Z., Sharif, S., Zain, A. M., Ghazali, M., and Saad, R. M., "Potential of conformal cooling channels in rapid heat cycle molding: A review", Adv. Polym. Tech., Vol.33, Paper No. 21381, 2014.
- Kim, W. S., Hong, M. P., Park, J. S., Lee, Y. S., Cha, K. J., Sung, J. H., Jung, M. H., and Lee, Y. H., "Case studies on applications of conformal cooling channel based on DMT technology", J. Kor. Soc. Manuf. Process Eng., Vol.14, pp. 9-14, 2015.
- Kim, C.-H., Oh, S. A., and Park, K., "Investigation of the functional characteristics of injection molds with conformal cooling channels", Trans. Korean Soc. Mech. Eng. A, Vol.44, pp. 681-688, 2020. https://doi.org/10.3795/ksme-a.2020.44.10.681
- Saifullah, A.B.M and Masood, S. H., "Cycle time reduction in injection molding with conformal cooling channels", Proceedings of the International Conference on Mechanical Engineering, Dhaka, Bangladesh, pp. 29-31, 2007.
- Oh, S.-H., Ha, J.-W., and Park, K., "Adaptive conformal cooling of injection mold using additively manufactured TPMS structures", Polymer, Vol.14, pp. 181-194, 2022. https://doi.org/10.3390/polym14010181
- Mayatal, B.-Z. and Shavit, A., "On the integral Joule-Thomson effect", Cryogenics, Vol.34, pp. 19-23, 1994. https://doi.org/10.1016/0011-2275(94)90047-7
- Matin, N. S. and Haghighi, B., "Calculation of the Joule-Thomson inversion curves from cubic equation of state", Fluid Phase Equilibrium, Vol.175, pp. 273-284, 2000. https://doi.org/10.1016/S0378-3812(00)00443-X
- Seidl, M., Bobek, J., Safka, J., Habr, J., Novakova, I., and Behalek, L., "Utilizing of inner porous structure in injection moulds for application of special cooling method", Journal of Physics: Conference Series 709 012203, pp. 1-5, 2016.
- Linde North America, "Liquid CO2 spot cooling gets into tight spots in molds", Plastics Technology, pp. 11, 2013.
- Kim, M. J. and Choi, J. H., "Study on the rapid cooling method of an injection mold using the Joule-Thomson effect", J. of Korean Soc. Manuf. Tech. Eng., Vol. 3, pp. 306-311, 2022.
- Bae, H. S., Park, D. H., and Lee, H. S., "Experimental study on hot-plate cooling with CO2 gas", Trans. Korean Soc. Mech. Eng. A, Vol.45, pp. 489-495, 2021. https://doi.org/10.3795/KSME-A.2021.45.6.489
- Bae, H. S., Park, D. H., and Lee, H. S., "Design of cooling module with CO2 for rapid cooling of injection mold", J. Korean Soc. Precis. Eng., Vol. 39, pp. 477-484, 2022. https://doi.org/10.7736/JKSPE.022.050