Advances in Computational Design

  • 제7권2호
  • /
  • Pages.129-137
  • /
  • 2022
  • /
  • 2383-8477(pISSN)
  • /
  • 2466-0523(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Mechanical and wear properties evaluation of Al/Al2O3 composites fabricated by combined compo-casting and WARB process

  • Vini, Mohamad Heydari (Department of Mechanical Engineering, Mobarakeh Branch, Islamic Azad University) ;
  • Daneshmand, Saeed (Department of Mechanical Engineering, Majlesi Branch, Islamic Azad University)
  • 투고 : 2020.12.27
  • 심사 : 2021.01.07
  • 발행 : 2022.04.25
⟨ 이전 논문 다음 논문 ⟩

초록

Compo-casting method is one of the popular technique to produce metal based matrix composites. But, one of the main challenges in this process is un-uniform spreading of reinforced subdivisions (particles) inside the metallic matrix and the lack of desirable mechanical properties of the final produced composites due to the low bonding strength among the metal matrix and reinforcement particles. To remove these difficulties and to promote the mechanical properties of these kind of composites, the WARM ARB technique was utilized as supplementary technique to heighten the mechanical and microstructural evolution of the casted Al/Al2O3 composite strips. The microstructure evolution and mechanical properties of these composites have been considered versus different WARM ARB cycles by tensile test, average Vickers micro hardness test, wear test and scanning electron microscopy (SEM). The SEM results revealed that during the higher warm- ARB cycles, big alumina clusters are broken and make a uniform distribution of alumina particles. It was shown that cumulating the forming cycles improved the mechanical properties of composites. In general, combined compo-casting and ARB process would consent making Al/Al2O3 composites with high consistency, good microstructural and mechanical properties.

키워드

참고문헌

  1. Alizadeh, M. (2010), "Comparison of nanostructured Al/B4C composite produced by ARB and Al/B4C composite produced by RRB process", Mater. Sci. Eng. A, 528(2), 578-582. https://doi.org/10.1016/j.msea.2010.08.093.
  2. Alizadeh, M. and Talebian, M. (2012), "Fabrication of Al/Cup composite by accumulative roll bonding pocess and investigation of mechanical properties", Mater. Sci. Eng. A, 558, 331-337. https://doi.org/10.1016/j.msea.2012.08.008.
  3. Amirkhanlou, S., Jamaati, R., Niroumand, B. and Toroghinejad, M.R. (2011), "Using ARB process as a solution for dilemma of Si and SiCP distribution in cast Al- Si/SiCP composites", J. Mater. Proc. Technol., 211(6), 1159-1165. https://doi.org/10.1016/j.jmatprotec.2011.01.019.
  4. Farhadipour, P., Sedighi, M. and Heydari, M. (2017), "Using warm accumulative roll bonding method to produce Al-Al2O3", Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture, 231(5), 889-896. https://doi.org/10.1177/0954405417703421
  5. Heydari Vini, M. and Daneshmand, S. (2020), "Effect of Tio2 particles on the mechanical, bonding properties and microstructural evolution of AA1060/TiO2 composites fabricated by WARM ARB", Adv. Mater. Res., 9(2), 99-107. https://doi.org/10.12989/amr.2020.9.2.099.
  6. Heydari Vini, M., Sedighi, M. and Mondali, M. (2017), "Mechanical properties, bond strength and microstructural evolution of AA1060/TiO2 composites fabricated by warm accumulative roll bonding (WARM ARB)", J. Mater. Res., 108(1), 53-59. https://doi.org/10.3139/146.111450.
  7. Ipek, R. (2005), "Adhesive wear behaviour of B4C and Sic reinforced 4147 Al matrix composites (Al/B4CAl/SiC)", J. Mater. Proc. Technol., 162-163, 71-75. https://doi.org/10.1016/j.jmatprotec.2005.02.207.
  8. Jamaati, R. and Toroghinejad, M.R. (2010), "Manufacturing of high-strength aluminum / alumina composite by accumulative roll bonding", Mater. Sci. Eng. A, 527(16-17), 4146-4151. https://doi.org/10.1016/j.msea.2010.03.070.
  9. Jamaati, R., Toroghinejad, M.R., Dutkiewicz, J. and Szpunar, J.A. (2012), "Investigation of nanostructured Al/Al2O3 composite produced by accumulative roll bonding process", Mater. Design, 35, 37-42. https://doi.org/10.1016/j.matdes.2011.09.040.
  10. Liu, C.Y., Wang, Q., Jia, Y.Z., Zhang, B., Jing, R., Ma, M.Z., Jing, Q. and Liu, R.P. (2012), "Effect of W particles on the properties of accumulatively roll-bonded Al/W composites", Mater. Sci. Eng. A, 547(15), 120-124. https://doi.org/10.1016/j.msea.2012.03.095.
  11. Liu, C.Y., Wang, Q., Jia, Y.Z., Zhang, B., Jing, R., Ma, M.Z., Jing, Q. and Liu, R.P. (2013), "Evaluation of mechanical properties of 1060-Al reinforced with WC particles via warm accumulative roll bonding process", Mater. Des., 43, 367-372. https://doi.org/10.1016/j.matdes.2012.07.019.
  12. Lu, C., Tieu, K. and Wexler, D. (2009), "Significant enhancement of bond strength in the accumulative roll bonding process using nano-sized sio2 particles", J. Mater. Proc. Technol., 209 (10), 4830-4834. https://doi.org/10.1016/j.jmatprotec.2009.01.003
  13. Pasebani, S. and Toroghinejad, M.R. (2010), "Nano-Grained 70-30 brass strip produced by accumulative roll-bonding (ARB) process", Mater. Sci. Eng. A, 527(3), 491-7. https://doi.org/10.1016/j.msea.2009.09.029.
  14. Saito, Y., Utsunomiya, H. and Tsuji, N. (1994), "Novel ultra-high straining process for bulk materials-development of the accumulative roll-bonding (ARB) process", Acta Materialia, 47(2), 579-583. https://doi.org/10.1016/S1359-6454(98)00365-6.
  15. Sedighi, M., Heydari Vini, M. and Farhadipour, P. (2016), "Effect of alumina content on the mechanical properties of AA5083/Al2O3 composites fabricated by warm accumulative roll bonding", Powder Metall. Met. C., 55(510), 413-418. https://doi.org/10.1007/s11106-016-9821-0.
  16. Su, L., Lu, C., Li, H., Deng, G. and Tieu, K. (2014), "Investigation of ultrafine grained AA1050 fabricated by accumulative roll bonding", Mater. Sci. Eng. A, 614, 148-155. https://doi.org/10.1016/j.msea.2014.07.032.