DOI QR코드

DOI QR Code

Parametric study on precast prestressed concrete double-tee girder for rural bridges

  • Nguyen, Dinh Hung (Department of Civil Engineering, International University-Vietnam National University Ho Chi Minh City Quarter 6) ;
  • Vu, Hong Nghiep (Department of Civil Engineering, Van Lang University) ;
  • Nguyen, Thac Quang (University of Transport and Communications, Campus in Ho Chi Minh City)
  • 투고 : 2021.05.15
  • 심사 : 2022.03.02
  • 발행 : 2022.03.25

초록

Bridges using double-tee (DT) girders from 12 m to 15 m are one of the good choices to improve accessibility in rural areas of the Mekong River Delta. In this study, nonlinear finite element method (FEM) analysis was conducted with different constitutive laws of materials. The FEM analysis results were compared to experimental results to confirm the applicability of the constitutive laws of materials for DT girders. A parametric study through FEM analysis was then conducted to investigate the effect of span lengths, top flange depths, and a number of prestressing tendons on the capacity of DT girders in order that propose DT girders for rural bridges. Parametric results showed that the top flange depth of a DT girder for rural bridges could be 120 mm. The DT girder with a span length of 12 m or 13 m could be used 16 tendons, while the DT girder with a span length of 14 m or 15 m could be set up with 20 tendons. The prestressed concrete DT girders based on FEM results can be suggested for the construction of rural bridges.

키워드

과제정보

This research is funded by Vietnam National University Ho Chi Minh City (VNU-HCM) under grant number C2020-28-07.

참고문헌

  1. AASHTO (2017), LRFD Bridge Construction Specifications, 8th Edition, Washington, DC, USA.
  2. Abdelatif, A.O., Owen, J.S. and Hussien, M.F.M. (2015), "Modelling the prestress transfer in pre-tensioned concrete elements", Fin. Elem. Anal. Des., 94, 47-63. https://doi.org/10.1016/j.finel.2014.09.007.
  3. ACI (1991), Standard Practice for Selecting Proportions for Normal, Heavyweight and Mass Concrete, ACI Committee 211 Report, ACI 211.1-91. Farmington Hills, MI, USA.
  4. ACI Committee 318 (2014), Building Code Requirements for Structural Concrete.
  5. ACI Committee 363 (1984), "State-of-the-art report on high-strength concrete", ACI J. Proc., 81(4), 364-411.
  6. Ahmad, S.H. and Shah, S.P., (1982), "Stress-strain curves of concrete confined by spiral reinforcement", ACI J. Proc., 79(6), 484-490.
  7. Alfarah, B., Almansa, F.L. and Oller, S. (2017), "New methodology for calculating damage variables evolution in Plastic Damage Model for RC structures", J. Eng. Struct., 132, 70-86. https://doi.org/10.1016/j.engstruct.2016.11.022.
  8. Allos, A.E. and Martin, L.H. (1981), "Factors affecting Poisson's ratio for concrete", J. Build. Envir., 16(1), 1-9. https://doi.org/10.1016/0360-1323(81)90041-X.
  9. ASCE Task Committee on Finite Element Analysis of Reinforced Concrete Structures (1982), "State-of-the-art report on finite element analysis of reinforced concrete", ASCE.
  10. Au, F.T.K. and Kwan. (2004), "A minimum ductility design method for non-rectangular high-strength concrete beams", Comput. Concrete, 1(2), 115-130. http://doi.org/10.12989/cac.2004.1.2.115.
  11. Au, F.T.K., Leung, C.C.Y. and Kwan, A.K.H. (2011), "Flexural ductility and deformability of reinforced and prestressed concrete sections", Comput. Concrete, 8(4), 473-489. https://doi.org/10.12989/cac.2011.8.4.473.
  12. Benyamina, S., Menadi, B., Bernard, S.K. and Kenai, S. (2019), "Performance of self-compacting concrete with manufactured crushed sand", Adv. Concrete Constr., 7(2), 87-96. https://doi.org/10.12989/acc.2019.7.2.087.
  13. Birtel, V. and Mark, P. (2006), "Parameterised finite element modelling of RC beam shear failure", ABAQUS Users' Conference.
  14. CEB-FIP (1995), Comite Euro-International du Beton, "High-performance concrete, recommended extensions to the Model code 90-Research needs", CEB Bull. d'Information, 228.
  15. Chen, Y., Feng, J. and Yin, S. (2012), "Compressive behavior of reinforced concrete columns confined by multi-spiral hoops", Comput. Concrete, 9(5), 341-355. http://doi.org/10.12989/cac.2012.9.5.341.
  16. Dere, Y. and Koroglu, M.A. (2017), "Nonlinear FE modeling of reinforced concrete", Int. J. Struct. Civil Eng. Res., 6(1), 71-74. https://doi.org/10.18178/ijscer.6.1.71-74
  17. Douk, N., Vu, X.H., Larbi, A.S., Audebert, M. and Chatelin, R. (2021), "Numerical study of thermomechanical behaviour of reinforced concrete beams with and without textile reinforced concrete (TRC) strengthening: Effects of TRC thickness and thermal loading rate", Eng. Struct., 231, 111737. https://doi.org/10.1016/j.engstruct.2020.111737.
  18. Eurocode 2 (2004), Design of Concrete Structures-Part 1, General Rules and Rules for Buildings.
  19. Hordijk, D.A. (1991), "Local approach to fatigue of concrete", Ph.D. Thesis of Philosophy, Delft University of Technology.
  20. Jankowiak, T. and Lodygowski, T. (2005), "Identification of parameters of concrete damage plasticity constitutive model", Found. Civil Envir. Eng., 6, 53-69.
  21. Kim, U., Huang, Y. Pinaki R. Chakrabarti, P.R. and Kang, T.H.K. (2014), "Modeling of post-tensioned one-way and two-way slabs with unbonded tendons", Comput. Concrete, 13(5), 587-601. http://doi.org/10.12989/cac.2014.13.5.587.
  22. Leonhardt, F. (1988), "Crack and crack control in concrete structures", PCI J., 124-145.
  23. Malm, R. (2006), "Shear crack in concrete structures subjected to in-plane stresses", Royal Inst. Tech., Stockholm, Sweden.
  24. Nguyen D.H. (2011), "Shear failure mechanisms of segmental concrete beams with external tendons", Ph.D. Thesis of Philosophy, Tokyo Institute of Technology.
  25. Nguyen, D.H., Vu, H.N. and Nguyen, T.Q. (2021), "Full-scale test of precast prestressed concrete double-tee girder for rural bridges", Adv. Bridge Eng., 2(1), 1-19. https://doi.org/10.1186/s43251-021-00044-9.
  26. Noguchi, T., Tomosawa, F., Nemati, K.M., Chiaia, B.M. and Fantilli, A.P. (2009), "A practical equation for elastic modulus of concrete", ACI Struct. J., 106(5), 690-696.
  27. Paliwal, G. and Marua, S. (2017), "Effect of fly ash and plastic waste on mechanical and durability properties of concrete", Adv. Concrete Constr., 5(6), 575-586. https://doi.org/10.12989/acc.2017.5.6.575.
  28. Radain, T.A., Samman, T.A. and Wafa, F.F. (1993), "Mechanical properties of high-strength concrete", Proceedings of the Third International Symposium on Utilization of High-Strength Concrete, 2, Lillehammer, Norway.
  29. Ren, W., Sneed, L.H., Yang, Y. and He, R. (2014), "Numerical simulation of prestressed precast concrete bridge deck panels using damage plasticity model", Int. J. Concrete Struct. Mater., 9(1), 45-54. https://doi.org10.1007/s40069-014-0091-2.
  30. Rimal, S., Kidd, B., Tazarv, M., Seo, J. and Wehbe, N. (2021), "Methodology for load rating of damaged double-tee girder bridges", J. Bridge Eng., 26(1), 04020110. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001651.
  31. Sethuraman V.S., Suguna K. and Raghunath P.N. (2017), "Numerical analysis of high strength concrete beams using ABAQUS", Int. J. Appl. Envir. Sci., 12(1), 201-210.
  32. Singh, A.K. (2014), "Evaluation of live-load distribution factors (LLDFs) of NEXT beam bridges", Master Thesis of Philosophy, University of Massachusetts.
  33. SIWRP (Southern Institute for Water Resources Planning) (2011), "Mekong Delta water resources assessment studies", Vietnam-Netherlands Mekong Delta Masterplan Project, Draft report.
  34. TCVN-10380:2014 (2014), Rural Roads-Specifications for Design. (in Vietnamese)
  35. TCVN-9346:2012 (2012), Concrete and Reinforced Concrete Structures-Requirement of Protection from Corrosion in Marine Environment. (in Vietnamese)
  36. Tejchman, J. and Bobinski, J. (2013), Continuous and Discontinuous Modelling of Fracture in Concrete Using FEM, Springer Heidelberg New York Dordrecht London.
  37. Thorenfeldt, E., Tomaszewicz, A. and Jensen, J.J. (1987), "Mechanical properties of high-strength concrete and application in design", Symposium Proceeding, Utilization of High-Strength Concrete, Norway.
  38. World Bank Document (2016), "Results-based operation for local bridge construction and road asset management", Program Appraisal Document, WB-P155086.
  39. Zoubek, B., Fahjan, Y., Fischinger, M. and Isakovic. T. (2014), "Nonlinear finite element modelling of centric dowel connections in precast buildings", Comput. Concrete, 14(4), 463-477. http://doi.org/10.12989/cac.2014.14.4.463.