Structural Engineering and Mechanics

  • 제81권6호
  • /
  • Pages.751-767
  • /
  • 2022
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Lateral-torsional buckling resistance of composite steel beams with corrugated webs

  • Shaheen, Yousry B.I. (Civil Engineering Department, Faculty of Engineering, Menoufia University) ;
  • Mahmoud, Ashraf M. (Civil Engineering Department, Faculty of Engineering, Modern University for Technology and Information (MTI))
  • 투고 : 2021.08.14
  • 심사 : 2021.12.30
  • 발행 : 2022.03.25
⟨ 이전 논문 다음 논문 ⟩

초록

In the hogging bending moment area, continuous composite beams are subjected to the ultimate limit state of lateral-torsional buckling (LTB), which depends on web stiffness as well as concrete slab and shear connection stiffnesses. The design of the LTB and the determination of the elastic critical moment are produced approximately, using the European Standard EN 1994-1-1:2004, for continuous composite steel beams, but is applicable only for those with a plane web steel profile. Also, and from the previous researches, the elastic critical moment of the continuous composite beams with corrugated sinusoidal web steel profiles was determined. In this paper, a finite element analysis (FEA) model was developed using the ANSYS 16 software, to determine the elastic critical moments of continuous composite steel beams with various corrugated web profiles, such as trapezoidal, zigzag, and rectangular profiles, which were evaluated against numerical data of the sinusoidal one from the literature. Ultimately, the failure load of a composite steel beam with various web profiles was predicted by studying 46 models, based on FEA modeling, and a procedure for predicting the elastic critical moment of composite beams with various web steel profiles was proposed. When compared to sinusoidal web profiles, the trapezoidal, zigzag, and rectangular web profiles required an average increase in load capacity and stiffness of 7%, 17.5%, and 28%, respectively, according to the finite element analysis. Also, the rectangular web steel profile has a greater stiffness and load capacity. In contrast, the sinusoidal web has lower values for these characteristics.

키워드

참고문헌

  1. ANSYS User Manual Release 16.0 (2015), ANSYS Inc, Canonsburg, Pennsylvania.
  2. Belis, J., Impe, R.V., Lagae, G. and Vanlaere, G. (2003), "Enhancement of the buckling strength of glass beams by means of lateral restraints", Struct. Eng. Mech., 15(5), 495-511. http://doi.org/10.12989/sem.2003.15.5.495.
  3. Cakiroglu, C., Bekdas, G., Kim, S. and Geem, Z.W. (2020), "Optimization of shear and lateral-torsional buckling of steel plate girders using Meta-Heuristic algorithms", Appl. Sci. J., 10, 2-14. https://doi.org/10.3390/app10103639.
  4. Calenzani, A.F.G., Fakury, R.H., Paula, F.A., Rodrigues, F.C., Queiroz, G. and Pimenta, R.J. (2012), "Rotational stiffness of continuous composite beams with sinusoidal-web profiles for torsional buckling", J. Constr. Steel Res., 79, 22-33. http://doi.org/10.1016/j.jcsr.2012.07.015.
  5. EN 1993-1-1, Eurocode 3 (2005), Design of Steel Structures-Part 1-1: General Rules and Rules for Buildings, European Committee for Standardization, Brussels, Belgium.
  6. EN 1994-1-1 Eurocode 4 (2004), Design of Composite Steel and Concrete Structures. Part 1-1: General Rules and Rules for Buildings, European Committee for Standardization, Brussels, Belgium.
  7. ENV 1994-1-1 Eurocode 4 (1992), Design of Composite Steel and Concrete Structures. Part 1-1: General Rules and Rules for Buildings, European Committee for Standardization, Brussels, Belgium.
  8. Feng, Y.L., Jiang, L.Z., Zhou, W.B. and Han, J.P. (2019), "Lateral-torsional buckling of box beam with corrugated steel webs", J. Central South Univ., 26(7), 1946-1957. http://doi.org/10.1007/s11717-019-4122-0.
  9. Franco, A.C.A. and Kudryavtsev, S. (2020), "Lateral-torsional buckling behavior of triangularly tapered corrugated web beam", IOP Conf. Ser.: Mater. Sci. Eng., 972(1), 012014. http://doi.org/10.1088/1757-899X/972/1/012014.
  10. Hanswille, G. (2002), "Lateral torsional buckling of composite beams-comparison of more accurate methods with Eurocode 4", Composite Construction in Steel and Concrete IV, 105-116. https://doi.org/10.1061/40616(281)10.
  11. Johnson, R.P. and Anderson, D. (2004), Designers' Guide to EN 1994-1-1: Eurocode 4: Design of Composite Steel and Concrete Structures, General Rules and Rules for Buildings, Thomas Telford.
  12. Kasiviswanathan, M. and Anbarasu, M. (2021), "Simplified approach to estimate the lateral torsional buckling of GFRP channel beams", Struct. Eng. Mech., 77(4), 523-533. http://doi.org/10.12989/sem.2021.77.4.523.
  13. Kudryavtsev, S. (2019), "Lateral-torsional buckling behaviour of triangularly corrugated web beam", IOP Conf. Ser.: Mater. Sci. Eng., 471(5), 052016. https://doi.org/10.1088/1757-899X/471/5/052016.
  14. Maali, M. (2019), "Experimental and numerical prediction of torsional behavior of steel beam with sinusoidal web", Iran. J. Sci. Technol., 44(1), 1-10. https://doi.org/10.1007/s40996-019-00304-9.
  15. Oliveira, J.P.S., Calenzani, A.F.G., Fakury, R.H. and Ferreira, W.G. (2016), "Elastic critical moment of continuous composite beams with a sinusoidal-web steel profile for lateral-torsional buckling", Eng. Struct., 113, 121-132. https://doi.org/10.1016/j.engstruct.2016.01.021.
  16. Roik, K., Hanswille, G. and Kina, J. (1990), "Solution for the lateral torsional buckling problem of composite beams", Stahlbau, 59(11), 327-332. (in German)
  17. Sedlacek, G. and Collin, P. (2003), "Composite bridge design for small and medium spans", ECSC Steel RTD Programme Report 20583, European Union (EU), Luxembourg.
  18. Shukry, M., Sharaf, T., Elsabbagh, A. and ELGhandour, M. (2020), "Parametric study on steel girders with corrugated webs", Port Said Eng. Res. J., 24(2), 86-96. http://doi.org/10.21608/pserj.2020.17735.1010.
  19. SP 294.1325800.2017 (2017), Steel Structures. Design Rules, Ministry of Construction of Russia. (in Russian)
  20. Zhu, J., Chen, J.K. and Ren, C. (2014), "Numerical study on the moment capacity of zed-section purlins under uplift loading", Struct. Eng. Mech., 49(2), 147-161. http://doi.org/10.12989/sem.2014.49.2.147.
  21. Ziane, N., Meftah, S.A., Ruta, G., Tounsi, A. and Bedia, E.A. (2015), "Simplified approach to estimate the lateral torsional buckling of GFRP channel beams", Struct. Eng. Mech., 54(3), 579-595. http://doi.org/10.12989/sem.2015.54.3.579.