Geomechanics and Engineering

  • 제28권6호
  • /
  • Pages.559-571
  • /
  • 2022
  • /
  • 2005-307X(pISSN)
  • /
  • 2092-6219(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Laboratory analysis of loose sand mixed with construction waste material in deep soil mixing

  • Alnunu, Mahdi Z. (Department of Civil Engineering, Engineering Faculty, Eastern Mediterranean University) ;
  • Nalbantoglu, Zalihe (Department of Civil Engineering, Engineering Faculty, Eastern Mediterranean University)
  • 투고 : 2021.02.19
  • 심사 : 2022.01.14
  • 발행 : 2022.03.25
⟨ 이전 논문 다음 논문 ⟩

초록

Deep soil mixing, DSM technique has been widely used to improve the engineering properties of problematic soils. Due to growing urbanization and the industrial developments, disposal of brick dust poses a big problem and causes environmental problems. This study aims to use brick dust in DSM application in order to minimize the waste in brick industry and to evaluate its effect on the improvement of the geotechnical properties. Three different percentages of cement content: (10, 15 and 20%) were used in the formation of soil-cement mixture. Unlike the other studies in the literature, various percentages of waste brick dust: (10, 20 and 30%) were used as partial replacement of cement in soil-cement mixture. The results indicated that addition of waste brick dust into soil-cement mixture had positive effect on the inherent strength and stiffness of loose sand. Cement replaced by 20% of brick dust gave the best results and reduced the final setting time of cement and resulted in an increase in unconfined compressive strength, modulus of elasticity and resilient modulus of sand mixed with cement and brick dust. The findings were also supported by the microscopic images of the specimens with different percentages of waste brick dust and it was observed that waste brick dust caused an increase in the interlocking between the particles and resulted in an increase in soil strength. Using waste brick dust as a replacement material seems to be promising for improving the geotechnical properties of loose sand.

키워드

참고문헌

  1. Al-Bared, M.A., Harahap, I.S., Marto, A., Mohamad, H., Abad, S. V.A.N.K. and Mustaffa, Z. (2020), "Cyclic behavior of RT-cement treated marine clay subjected to low and high loading frequencies", Geomech. Eng., 21(5), 433-445. https://doi.org/10.12989/gae.2020.21.5.433.
  2. Al-Tabba, A., Ayotamuno, M.J. and Martin, R.J. (2000), "Soil mixing of stratified contaminated sands", J. Hazard. Mater., 72(1), 53-75. https://doi.org/10.1016/S0304-3894(99)00158-2.
  3. Arasan, S., Isik, F., Akbulut, R.K., Zaimoglu, A.S. and Nasirpur, O. (2015), "Rapid stabilization of sands with deep mixing method using polyester", Periodica Polytechnica Civil Eng., 59(3), 405-411. https://doi.org/10.3311/PPci.7956.
  4. Arulrajah, A., Yaghoubi, M., Disfani, M.M., Horpibulsuk, S., Bo, M.W. and Leong, M. (2018), "Evaluation of fly ash-and slag-based geopolymers for the improvement of a soft marine clay by deep soil mixing", Soils Found., 58(6), 1358-1370. https://doi.org/10.1016/j.sandf.2018.07.005.
  5. ASTM C188-09. (2014), Standard Test Method for Density of Hydraulic Cement, ASTM International, West Conshohocken, USA. www.astm.org.
  6. ASTM C191-19. (2019), Standard Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle, ASTM International, West Conshohocken, USA. www.astm.org.
  7. ASTM C204-07. (2011), Standard Test Methods for Fineness of Hydraulic Cement by Air-Permeability Apparatus, ASTM International, West Conshohocken, USA. www.astm.org.
  8. ASTM D1556-07. (2015), Standard Test Method for Density and Unit Weight of Soil in Place by the Sand-Cone Method, ASTM International, West Conshohocken, USA. www.astm.org.
  9. ASTM D1633-17. (2017), Standard Test Methods for Compressive Strength of Molded Soil-Cement Cylinders 1, ASTM International, West Conshohocken, USA. www.astm.org.
  10. ASTM D4254-00. (2017), Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density, ASTM International, West Conshohocken, USA. www.astm.org.
  11. ASTM D6913 / D6913M-17. (2017), Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis, ASTM International, West Conshohocken, USA. www.astm.org.
  12. ASTM D7348-21. (2021), Standard Test Methods for Loss on Ignition (LOI) of Solid Combustion Residues, ASTM International, West Conshohocken, USA. www.astm.org.
  13. ASTM D7382-20. (2020), Standard Test Methods for Determination of Maximum Dry Unit Weight of Granular Soils Using a Vibrating Hammer, ASTM International, West Conshohocken, USA. www.astm.org.
  14. ASTM D854-14. (2016), Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer, ASTM International, West Conshohocken, USA. www.astm.org.
  15. Brasse, K., Tracz, T., Zdeb, T. and Rychlewski, P. (2018), "Influence of soil-cement composition on its selected properties", Proceeding of the 8th Scientific-Technical Conference on Material Problems in Civil Engineering. https:/doi.org/10.1051/matecconf/201816306006.
  16. Bredenberg, H. (2017), Dry Mix Methods for Deep Soil Stabilization, Routledge, London, UK. http://dx.doi.org/10.1201/9781315141466.
  17. Bruce, D.A. and Bruce, M.E.C. (2002), "The practitioner's guide to deep mixing", Geotech. Special Publication, 1, 474-488. https://doi.org/10.1061/40663(2003)22.
  18. Canakci, H., Gullu, H. and Dwle, M.I.K. (2018), "Effect of glass powder added grout for deep mixing of marginal sand with clay", Arabian J. Sci. Eng., 43(4), 1583-1595. https://doi.org/10.1007/s13369-017-2655-3.
  19. Chang, M., Mao, T.W. and Huang, R.C. (2016), "A study on the improvements of geotechnical properties of in-situ soils by grouting", Geomech. Eng., 10(4), 527-546. https://doi.org/10.12989/gae.2016.10.4.527.
  20. Chenari, R.J., Fatahi, B., Ghorbani, A. and Alamoti, M.N. (2018), "Evaluation of strength properties of cement stabilized sand mixed with EPS beads and fly ash", Geomech. Eng., 14(6), 533-544. https://doi.org/10.12989/gae.2018.14.6.533.
  21. Chhun, K.T., Choo, H., Kaothon, P. and Yune, C.Y. (2020), "Experimental study on the strength behavior of cement-stabilized sand with recovered carbon black", Geomech. Eng., 23(1), 31-38. https://doi.org/10.12989/gae.2020.23.1.031.
  22. Cristelo, N., Glendinning, S. and Teixeira Pinto, A. (2011), "Deep soft soil improvement by alkaline activation", Proceedings of the Institution of Civil Engineers-Ground Improvement, 164(2), 73-82. https://doi.org/10.1680/grim.900032.
  23. Demir, I., Yaprak, H.A.S.B.I. and Simsek, O. (2011), "Performance of cement mortars replaced by ground waste brick in different aggressive conditions", Ceramics-Silikaty, 55(3), 268-275.
  24. Egorova, A.A., Rybak, J., Stefaniuk, D. and Zajaczkowski, P. (2017), "Basic aspects of deep soil mixing technology control", Proceedings of the IOP Conference Series: Materials Science and Engineering, Moscow, Russia. https://doi.org/10.1088/1757-899X/245/2/022019.
  25. Esmaeili, M., Astaraki, F. and Khajehei, H. (2020), "Laboratory investigation on the effect of microsilica additive on mechanical properties of deep soil mixing columns in loose sandy soils", Eur. J. Environ. Civil Eng., 24(3), 321-335. https://doi.org/10.1080/19648189.2017.1382394.
  26. Esmaeili, M., Gharouni-Nik, M. and Khajehei, H. (2014), "Evaluation of deep soil mixing efficiency in stabilizing loose sandy soils using laboratory tests", Geotech. Test. J., 37(5), 817-827. https://doi.org/10.1520/GTJ20130099.
  27. EuroSoilStab. (2002), "Development of design and construction methods to stabilize soft organic soils: Design guide soft soil stabilization", CT97-0351, Project No. BE 96-3177.
  28. Fang, Y.S., Chung, Y.T., Yu, F.J. and Chen, T.J. (2001), "Properties of soil-cement stabilised with deep mixing method", Proceedings of the Institution of Civil Engineers-Ground Improvement, 5(2), 69-74. https://doi.org/10.1680/grim.2001.5.2.69.
  29. Farouk, A. and Shahien, M.M. (2013), "Ground improvement using soil-cement columns: Experimental investigation", Alexandria Eng. J., 52(4), 733-740. https://doi.org/10.1016/j.aej.2013.08.009.
  30. Fatahi, B. and Khabbaz, H. (2012), "Mechanical characteristics of soft clay treated with fibre and cement", Geosynthetics Int., 19(3), 252-262. https://doi.org/10.1680/gein.12.00012.
  31. Ge, Z., Gao, Z., Sun, R. and Zheng, L. (2012), "Mix design of concrete with recycled clay-brick-powder using the orthogonal design method", Constr. Build. Mater., 31, 289-293. https://doi.org/10.1016/j.conbuildmat.2012.01.002.
  32. Ge, Z., Wang, Y., Sun, R., Wu, X. and Guan, Y. (2015), "Influence of ground waste clay brick on properties of fresh and hardened concrete", Constr. Build. Mater., 98, 128-136. https://doi.org/10.1016/j.conbuildmat.2015.08.100.
  33. George, K.P. (2004), "Prediction of resilient modulus from soil index properties", Research Report No. FHWA/MS-DOT-RD04-172; The Mississippi Department of Transportation and US Department of Transportation-federal Highway Adminstration, Australia.
  34. Gullu, H., Canakci, H. and Al Zangana, I.F. (2017), "Use of cement based grout with glass powder for deep mixing", Constr. Build. Mater., 137, 12-20. https://doi.org/10.1016/j.conbuildmat.2017.01.070.
  35. Gupta, D. and Kumar, A. (2017), "Stabilized soil incorporating combinations of rice husk ash, pond ash and cement", Geomech. Eng., 12(1), 85-109. https://doi.org/10.12989/gae.2017.12.1.085.
  36. Haakeel, M.S.S., Ramzi, M.Z.M. and Nasvi, M.C.M. (2019), "Compressibility behaviour of peat reinforced with single and Multiple Deep Soil Mixing (DSM) columns", Engineer: J. Inst. Engineers, 52(3). https://doi.org/10.4038/engineer.v52i3.7360.
  37. Hasheminezhad, A. and Bahadori, H. (2020), "On the deep soil mixing method in the mitigation of liquefaction-induced bearing capacity degradation of shallow foundations", Geomech. Geoeng., 1-13. http://dx.doi.org/10.1080/17486025.2020.1755460.
  38. Heidari, A. and Hasanpour, B. (2013), "Effects of waste bricks powder of gachsaran company as a pozzolanic material in concrete", Asian J. Civil Eng.(Building and Housing), 14, 755-763.
  39. Horpibulsuk, S., Miura, N., Koga, H. and Nagaraj, T.S. (2004), "Analysis of strength development in deep mixing: a field study", Proceedings of the Institution of Civil Engineers-Ground Improvement, 8(2), 59-68. https://doi.org/10.1680/grim.2004.8.2.59.
  40. Huang, J., Kelly, R. and Sloan, S.W. (2015), "Stochastic assessment for the behaviour of systems of dry soil mix columns", Comput. Geotech., 66, 75-84. https://doi.org/10.1016/j.compgeo.2015.01.016.
  41. Jacobson, J.R., Filz, G.M. and Mitchell, J.K. (2003), Factors affecting strength gain in lime-cement columns and development of a laboratory testing procedure, Research Report No. 57565; Virginia Center for Transportation Innovation and Research, Virginia, USA.
  42. Jung, C., Ceglarek, R., Clauvelin, T., Ayeldeen, M. and Kim, D. (2020), "Deep Soil Mixing in Sabkha Soils for Foundation Support in United Arab Emirates", Int. J. Geosynthetics Ground Eng., 6(1), 1-15. https://doi.org/10.1007/s40891-020-0188-4.
  43. Karpisz, I., Pyda, J., Cichy, L. and Sobala, D. (2018), "Study of the effect of cement amount on the soil-cement sample strength", Proceedings of the IOP Conference Series: Materials Science and Engineering, Wroclaw, Poland. https:/doi.org/10.1088/1757-899X/365/4/042061.
  44. Khan, M.N.A., Liaqat, N., Ahmed, I., Basit, A., Umar, M. and Khan, M.A. (2018), "Effect of Brick Dust on Strength and Workability of Concrete", Proceedings of the IOP Conference Series: Materials Science and Engineering, Pakistan. http://doi:10.1088/1757-899X/414/1/012005.
  45. Kim, Y.S., Seo, S.G., Ko, H.W. and Kim, J. (2018), "Implementation of porous material through eco-tech for deep cement-soil mixing", Mar. Georesour. Geotech., 36(8), 931-939. https://doi.org/10.1080/1064119X.2017.1399944.
  46. Le Kouby, A., Guimond-Barrett, A., Reiffsteck, P., Pantet, A., Mosser, J.F. and Calon, N. (2020), "Improvement of existing railway subgrade by deep mixing", Eur. J. Environ. Civil Eng., 24(8), 1229-1244. http://dx.doi.org/10.1080/19648189.2018.1456977.
  47. Lee, C., Nam, H., Lee, W., Choo, H. and Ku, T. (2019), "Estimating UCS of cement-grouted sand using characteristics of sand and UCS of pure grout", Geomech. Eng., 19(4), 343-352. https://doi.org/10.12989/gae.2019.19.4.343.
  48. Li, Y.P., Chen, L.Z. and Wang, Y.H. (2005), "Experimental research on pre-cracked marble under compression", Int. J. Solid. Struct., 42(9-10), 2505-2516. https://doi.org/10.1016/j.ijsolstr.2004.09.033.
  49. Liu, Y., Jiang, Y.J., Xiao, H. and Lee, F.H. (2017), "Determination of representative strength of deep cement-mixed clay from core strength data", Geotechnique, 67(4), 350-364. https://doi.org/10.1680/jgeot.16.P.105.
  50. Lorenzo, G.A. and Bergado, D.T. (2006), "Fundamental characteristics of cement-admixed clay in deep mixing", J. Mater. Civil Eng., 18(2), 161-174. https://doi.org/10.1061/(ASCE)0899-1561(2006)18:2(161).
  51. Lu, Y., Liu, S., Zhang, Y., Li, Z. and Xu, L. (2020), "Freeze-thaw performance of a cement-treated expansive soil", Cold Regions Sci. Technol., 170, 102926. https://doi.org/10.1016/j.coldregions.2019.102926.
  52. Ma, S.J., Li, M.Y., Guo, Y.C. and Safaei, B. (2020), "Field test and research on shield cutting pile penetrating cement soil single pile composite foundation", Geomech. Eng., 23(6), 513. https://doi.org/10.12989/gae.2020.23.6.513.
  53. Madhyannapu, R.S., Puppala, A.J., Nazarian, S. and Yuan, D. (2009), "Quality assessment and quality control of deep soil mixing construction for stabilizing expansive subsoils", J. Ggeotech. Geoenviron. Eng., 136(1), 119-128. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000188.
  54. Mann, M.F. (2017), "Effect of Deep-Soil Mixed Soil Reinforced Panels on Reducing Seismic Amplification on Soft ClayComparison Between the Rigid Wall and Laminar Containers", California State University, Fullerton, USA.
  55. Nazzal, M.D. and Mohammad, L.N. (2010), "Estimation of resilient modulus of subgrade soils for design of pavement structures", J. Mater. Civil Eng., 22(7), 726-734. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000073.
  56. O'Farrell, M., Sabir, B.B. and Wild, S. (2006), "Strength and chemical resistance of mortars containing brick manufacturing clays subjected to different treatments", Cement Concrete Compos., 28(9), 790-799. https://doi.org/10.1016/j.cemconcomp.2006.05.014.
  57. Onal, O. and Sariavci, C. (2019), "Stabilization of Meles Delta soils using cement and lime mixtures", Geomech. Eng., 19(6), 543-554. https://doi.org/10.12989/gae.2019.19.6.533.
  58. Park, D.W., Vo, H.V. and Lim, Y. (2014), "Recycling of dredged soil waste using air-foam stabilization method as highway construction material". In Innovative and Sustainable Use of Geomaterials and Geosystems, 41-48. https://doi.org/10.1061/9780784478455.006.
  59. Patterson, J. and Wilk, C.M. (2019), "Estimating Sustainability Benefits from Use of Blended Cements and Slag Cement at Geotechnical Projects", In IAEG/AEG Annual Meeting Proceedings, San Francisco, California, 4 (111-115). Springer, Cham. http://dx.doi.org/10.1007/978-3-319-93133-3_15.
  60. Rahim, A.M. (2005), "Subgrade soil index properties to estimate resilient modulus for pavement design", Int. J. Pavement Eng., 6(3), 163-169. https://doi.org/10.1080/10298430500140891.
  61. Rakhimova, N.R. and Rakhimov, R.Z. (2015), "Alkali-activated cements and mortars based on blast furnace slag and red clay brick waste", Mater. Design, 85, 324-331. https://doi.org/10.1016/j.matdes.2015.06.182.
  62. Rashid, A.S.A., Kueh, A.B.H. and Mohamad, H. (2017), "Behaviour of soft soil improved by floating soil-cement columns", Int. J. Phys. Model. Geotech., 18(2), 95-116. https://doi.org/10.1680/jphmg.15.00041.
  63. Ribeiro, D., Neri, R. and Cardoso, R. (2016), "Influence of water content in the UCS of soil-cement mixtures for different cement dosages", Procedia Eng., 143, 59-66. https://doi.org/10.1016/j.proeng.2016.06.008.
  64. Rogers, S.B. (2011), "Evaluation and testing of brick dust as a pozzolanic additive to lime mortars for architectural conservation", Master's Thesis; University of Pennsylvania, Philadelphia, PA.
  65. Rosato, D.V. (2003), Plastics engineered product design. Elsevier.
  66. Saberian, M., Moradi, M., Vali, R. and Li, J. (2018), "Stabilized marine and desert sands with deep mixing of cement and sodium bentonite", Geomech. Eng., 14(6), 553-562. https://doi.org/10.12989/gae.2018.14.6.553.
  67. Sas, W., Gluchowski, A. and Szymanski, A. (2012), "Determination of the Resilient modulus MR for the lime stabilized clay obtained from the repeated loading CBR tests", Annals of Warsaw University of Life Sciences-SGGW. Land Reclamation, 44(2). https://doi.org/10.2478/v10060-011-0070-0.
  68. Seifan, M., Mendoza, S. and Berenjian, A. (2020), "Mechanical properties and durability performance of fly ash based mortar containing nano-and micro-silica additives", Constr. Build. Mater., 252, 119121. https://doi.org/10.1016/j.conbuildmat.2020.119121.
  69. Sukontasukkul, P. and Jamsawang, P. (2012), "Use of steel and polypropylene fibers to improve flexural performance of deep soil-cement column", Constr. Build. Mater., 29, 201-205. https://doi.org/10.1016/j.conbuildmat.2011.10.040.
  70. Tang, C., Shi, B., Gao, W., Chen, F. and Cai, Y. (2007), "Strength and mechanical behavior of short polypropylene fiber reinforced and cement stabilized clayey soil", Geotext. Geomembranes, 25(3), 194-202. https://doi.org/10.1016/j.geotexmem.2006.11.002.
  71. Thompson, M.R. (1965), Shear strength and elastic properties of lime-soil mixtures, Transportation research board, USA.
  72. Timoney, M.J., McCabe, B.A. and Bell, A.L. (2012), "Experiences of dry soil mixing in highly organic soils", Proceedings of the Institution of Civil Engineers-Ground Improvement, 165(1), 3-14. https://doi.org/10.1680/grim.2012.165.1.3.
  73. Tong, B., Schaefer, V., Liu, Y. and Han, B. (2019), "Optimization of deep mixing design for seismic liquefaction mitigation of Caisson walls", Geomatics, Natural Hazards and Risk, 10(1), 287-313. https://doi.org/10.1080/19475705.2018.1521879.
  74. Venkatesh, N., Heeralal, M. and Pillai, R. J. (2018), "Resilient and permanent deformation behaviour of clayey subgrade soil subjected to repeated load triaxial tests", Eur. J. Environ. Civil Eng., 1-16. https://doi.org/10.1080/19648189.2018.1472041.
  75. Wang, J.H., Xu, Z.H. and Wang, W.D. (2009), "Wall and ground movements due to deep excavations in Shanghai soft soils", J. Geotech. Geoenviron. Eng., 136(7), 985-994. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000299.
  76. Wang, Y., Li, L., Li, J. and Sun, D.A. (2020), "Jet-grouting in ground improvement and rotary grouting pile installation: Theoretical analysis", Geomech. Eng., 21(3), 279-288. https://doi.org/10.12989/gae.2020.21.3.279.
  77. Wong, C.L., Mo, K.H., Yap, S.P., Alengaram, U.J. and Ling, T.C. (2018), "Potential use of brick waste as alternate concrete-making materials: A review", J. Cleaner Oroduction, 195, 226-239. https://doi.org/10.1016/j.jclepro.2018.05.193.
  78. Wong, J.K.H., Kok, S.T. and Wong, S.Y. (2020), "Cementitious, pozzolanic and filler materials for DSM binders", Civil Eng. J., 6(2), 402-417. https://doi.org/10.28991/cej-2020-03091479.
  79. Yadav, J.S., Hussain, S., Tiwari, S.K. and Garg, A. (2019), "Assessment of the load-deformation behaviour of rubber fibre-reinforced cemented clayey soil", T. Infrastruct. Geotech., 6(2), 105-136. https://doi.org/10.1007/s40515-019-00073-y
  80. Yang, S.Q., Dai, Y.H., Han, L.J. and Jin, Z.Q. (2009), "Experimental study on mechanical behavior of brittle marble samples containing different flaws under uniaxial compression", Eng. Fract. Mech., 76(12), 1833-1845. https://doi.org/10.1016/j.engfracmech.2009.04.005.
  81. Yang, S.R., Lin, H.D., Kung, J.H. and Huang, W.H. (2008), "Suction-controlled laboratory test on resilient modulus of unsaturated compacted subgrade soils", J. Geotech. Geoenviron. Eng., 134(9), 1375-1384. https://doi.org/10.1061/(asce)1090-0241(2008)134:9(1375).
  82. Yapage, N.N.S., Liyanapathirana, D.S., Kelly, R.B., Poulos, H.G. and Leo, C. J. (2014), "Numerical modeling of an embankment over soft ground improved with deep cement mixed columns: case history", J. Geotech. Geoenviron. Eng., 140(11), 04014062. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001165.
  83. Yi, Y., Liu, S., Puppala, A.J. and Jing, F. (2019), "Variable-diameter deep mixing column for multi-layered soft ground improvement: Laboratory modeling and field application", Soils Found., 59(3), 633-643. https://doi.org/10.1016/j.sandf.2019.01.009.
  84. Yilmaz, Y., Eun, J. and Goren, A. (2018), "Individual and combined effect of Portland cement and chemical agents on unconfined compressive strength for high plasticity clayey soils", Geomech. Eng., 16(4), 375-384. https://doi.org/10.12989/gae.2018.16.4.375.
  85. Yoobanpot, N., Jamsawang, P. and Horpibulsuk, S. (2017), "Strength behavior and microstructural characteristics of soft clay stabilized with cement kiln dust and fly ash residue", Appl. Clay Sci., 141, 146-156. https://doi.org/10.1016/j.clay.2017.02.028.
  86. Zhang, F., Zhang, L., Yang, L., Feng, T., Chen, L. and Zhong, X. (2018), "The cement content measurement of cement mixing piles with EDTA titration method", KSCE J. Civil Eng., 1-10. https://doi.org/10.1007/s12205-018-1215-z.