Advances in concrete construction

  • 제13권 2호
  • /
  • Pages.163-181
  • /
  • 2022
  • /
  • 2287-5301(pISSN)
  • /
  • 2287-531X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Numerical analysis and eccentric bearing capacity of steel reinforced recycled concrete filled circular steel tube columns

  • Ma, Hui (School of Civil Engineering and Architecture, Xi'an University of Technology) ;
  • Liu, Fangda (School of Civil Engineering and Architecture, Xi'an University of Technology) ;
  • Wu, Yanan (School of Civil Engineering and Architecture, Xi'an University of Technology) ;
  • Cui, Hang (School of Civil Engineering and Architecture, Xi'an University of Technology) ;
  • Zhao, Yanli (Research and Design Institute of water conservancy and hydropower, Xi'an University of Technology)
  • 투고 : 2020.04.24
  • 심사 : 2022.02.18
  • 발행 : 2022.02.25
⟨ 이전 논문 다음 논문 ⟩

초록

To study the mechanical properties of steel reinforced recycled concrete (SRRC) filled circular steel tube columns under eccentric compression loads, this study presents a finite element model which can simulate the eccentrically compressed columns using ABAQUS software. The analytical model was established by selecting the reasonable nonlinear analysis theory and the constitutive relationship of materials in the columns. The influences of design parameters on the eccentric compressive performance of columns were also considered in detail, such as the diameter-thickness ratio of circular steel tube, replacement percentage of recycled coarse aggregate (RCA), slenderness ratio, eccentricity, recycled aggregate concrete (RAC) strength and steel strength and so on. The deformation diagram, stress nephogram and load-displacement curves of the eccentrically compressed columns were obtained and compared with the test results of specimens. The results show that although there is a certain error between the calculation results and the test results, the error is small, which shows the rationality on the numerical model of eccentrically compressed columns. The failure of the columns is mainly due to the symmetrical bending of the columns towards the middle compression zone, which is a typical compression bending failure. The eccentric bearing capacity and deformation capacity of columns increase with the increase of the strength of steel tube and profile steel respectively. Compared with profile steel, the strength of steel tube has a greater influence on the eccentric compressive performance of columns. Improving the strength of RAC is beneficial to the eccentric bearing capacity of columns. In addition, the eccentric bearing capacity and deformation capacity of columns decrease with the increase of replacement percentage of RCA. The section form of profile steel has little influence on the eccentric compression performance of columns. On this basis, the calculation formulas on the nominal eccentric bearing capacity of columns were also put forward and the results calculated by the proposed formulas are in good agreement with the test values.

키워드

과제정보

The research was financially supported by the National Natural Science Foundation of China P.R. (No. 5140848), The Project Supported by Natural Science Basic Research Plan in Shaanxi Province of China (No. No. 2022JM-258, 2021JM-332), which is gratefully acknowledged.

참고문헌

  1. Abed, M. and Nemes, R. (2019), "Long-term durability of self-compacting high-performance concrete produced with waste materials", Constr. Build. Mater., 212(7), 350-361. https://doi.org/10.1016/j.conbuildmat.2019.04.004.
  2. Cai, S.H. (1989), "Calculation and Application of CFST Structure", China Construction and Industry Press, Beijing. (In Chinese)
  3. Cardoso, R., Silva, R.V., De Brito, J. and Dhir, R.K. (2016), "Use of recycled aggregates from construction and demolition waste in geotechnical applications: A literature review", Waste Manag., 49(3), 131-145. https://doi.org/10.1016/j.wasman.2015.12.021.
  4. Chitawadagi, M.V., Narasimhan, M.C. and Kulkarni, S.M. (2010), "Axial strength of circular concrete-filled steel tube columnsDOE approach", J. Constr. Steel. Res., 66(10), 1248-1260. https://doi.org/10.1016/j.jcsr.2010.04.006.
  5. Choi, W.C. and Yun, H.D. (2012), "Compressive behavior of reinforced concrete columns with recycled aggregate under uniaxial loading", Eng. Struct., 41(8), 285-293. https://doi.org/10.1016/j.engstruct.2012.03.037.
  6. Ding, F.X., Fu, L. and Yu, Z.W. (2017), "Behaviors of axially loaded square concrete-filled steel tube (CFST) Stub columns with notch in steel tube', Thin Wall. Struct., 115(6), 196-204. https://doi.org/10.1016/j.tws.2017.02.018.
  7. Djelloul, O.K., Menadi, B., Wardeh, G. and Kenai, S. (2018), "Performance of self-compacting concrete made with coarse and fine recycled concrete aggregates and ground granulated blast-furnace slag", Adv. Concrete Constr., 6(2), 103-121. https://doi.org/10.12989/acc.2018.6.2.103.
  8. Ellobody, E. (2013), "Nonlinear behaviour of eccentrically loaded FR concrete-filled stainless steel tubular columns", J. Constr. Steel. Res., 90(11), 1-12. https://doi.org/10.1016/j.jcsr.2013.07.018.
  9. Etxeberria, M., Vazquez, E., Mari, A. and Barra, M. (2007), "Influence of amount of recycled coarse aggregates and production process on properties of recycled aggregate concrete", Cement Concrete Res., 37(5), 735-742. https://doi.org/10.1016/j.cemconres.2007.02.002.
  10. Guo, Z.H. and Wang, C.Z. (1991), "Investigation of strength and failure criterion of concrete under multi-axial stresses", China Civ. Eng. J., 24(3), 1-14. (In Chinese)
  11. Han, L.H. (2007) "Concrete filled steel tubular structures", Science Press, Beijing. (In Chinese)
  12. Kadhim, I.T. and Guneyisi, E.M. (2018), "Code based assessment of load capacity of steel tubular columns infilled with recycled aggregate concrete under compression", Constr. Build. Mater., 168(4), 715-731. https://doi.org/10.1016/j.conbuildmat.2018.02.088.
  13. Lai, Y.Y., Yeh, L.H., Chen, P.F., Sung, P.H. and Lee, Y.M. (2016), "Management and recycling of construction waste in Taiwan", Proc. Envir. Sci., 35, 723-730. https://doi.org/10.1016/j.proenv.2016.07.077.
  14. Levy, S.M. and Helene, P. (2004), "Durability of recycled aggregates concrete: a safe way to sustainable development", Waste Manag., 34(11), 1975-1980. https://doi.org/10.1016/j.cemconres.2004.02.009.
  15. Liu, C.Q., Fang, D.J. and Zhao, L.J. (2021), "Reflection on earthquake damage of buildings in 2015 Nepal earthquake and seismic measures for post-earthquake reconstruction", Struct., 30(4), 647-658. https://doi.org/10.1016/j.istruc.2020.12.089.
  16. Liu, Y.C., Lyu, F., Ding, F.X., Wang, E., Xu, Y.L., Yuan, T., Deng, C. and Luo, C. (2021), "Numerical study on confinement effect and efficiency of concentrically loaded RACFRST stub columns", Front. Mater., 8, 630774. https://doi.org/10.3389/fmats.2021.630774.
  17. Ma, H., Dong, J., Hu, G.B. and Liu, Y.H. (2019), "Axial compression performance of composite short columns composed of RAC-filled square steel tube and profile steel", J. Constr. Steel. Res., 153(2), 416-430. https://doi.org/10.1016/j.jcsr.2018.10.018.
  18. Ma, H., Dong, J., Liu, Y.H. and Guo, T.T. (2018), "Compressive behavior of composite columns composed of RAC-filled circular steel tube and profile steel under axial loading", J. Constr. Steel. Res., 143(4), 72-82. https://doi.org/10.1016/j.jcsr.2017.12.020.
  19. Ma, H., Jia, C.J., Xi, J.C., Dong, J., Zhang, X.C. and Zhan, Y.L. (2021), "Cyclic loading test and nonlinear analysis on composite frame consisting of steel reinforced recycled concrete columns and steel beams", Eng. Struct., 241(8), 112480. https://doi.org/10.1016/j.engstruct.2021.112480.
  20. Ma, H., Xi, J.C., Zhao, Y.L. and Dong, J.K. (2021), "Mechanical behaviour of composite columns composed of RAC-filled square steel tube and profile steel under eccentric compression loads", Steel Compos. Struct., 38(1), 103-120. https://doi.org/10.12989/scs.2021.38.1.103.
  21. Manzi, S., Mazzotti, C. and Bignozzi, M.C. (2013) "Short and long-term behavior of structural concrete with recycled concrete aggregate", Cement Concrete Compos., 37(3), 312-318. https://doi.org/10.1016/j.cemconcomp.2013.01.003.
  22. Mefteh, H., Kebaili, O., Oucief, H., Berredjem, L. and Arabi, N. (2013), "Influence of moisture conditioning of recycled aggregates on the properties of fresh and hardened concrete", J. Clean. Prod., 54(9), 282-288. https://doi.org/10.1016/j.jclepro.2013.05.009.
  23. Silva, R.V., De Brito, J. and Dhir, R.K. (2014), "Properties and composition of recycled aggregates from construction and demolition waste suitable for concrete production", Constr. Build. Mater., 65(10), 201-217. https://doi.org/10.1016/j.conbuildmat.2014.04.117.
  24. Silva, R.V., Neves, R., De Brito, J. and Dhir, R.K. (2015), "Carbonation behaviour of recycled aggregate concrete", Cement Concrete Compos., 62(9), 22-32. https://doi.org/10.1016/j.cemconcomp.2015.04.017.
  25. Tam, V.W.Y., Soomro, M. and Evangelista, A.C.J. (2018), "A review of recycled aggregate in concrete applications (2000-2017)", Constr. Build. Mater., 172(3), 272-292. https://doi.org/10.1016/j.conbuildmat.2018.03.240.
  26. Tang, Y.C., Li, L.J., Feng, W.X., Liu, F. and Zhu, M. (2018), "Study of seismic behavior of recycled aggregate concrete-filled steel tubular columns", J. Constr. Steel. Res., 148(9), 1-15. https://doi.org/10.1016/j.jcsr.2018.04.031.
  27. Verian, K.P, Ashraf, W. and Cao, Y. (2018) "Properties of recycled concrete aggregate and their influence in new concrete production", Res., Conserv. Recycl., 133(6), 30-49. https://doi.org/10.1016/j.resconrec.2018.02.005.
  28. Verma, S.K. and Ashish, D.K. (2017), "Mechanical behavior of concrete comprising successively recycled concrete aggregates", Adv. Concrete Constr., 5(4), 303-311. https://doi.org/10.12989/acc.2017.5.4.303.
  29. Xiao, J.Z. (2008), "Recycled concrete", China Architecture and Building Press, Beijing. (In Chinese)
  30. Xiao, J.Z. and Lan, Y. (2006), "Experimental study on uniaxial tensile properties of recycled concrete", J. Build. Mater., 9(2), 154-158. (In Chinese) https://doi.org/10.3969/j.issn.1007-9629.2006.02.005
  31. Xiao, J.Z., Huang, X. and Shen, L.M. (2012), "Seismic behavior of semi-precast column with recycled aggregate concrete", Constr. Build. Mater., 35, 988-1001. https://doi.org/10.1016/j.conbuildmat.2012.04.062.
  32. Xiao, J.Z., Li, J.B. and Zhang, C. (2005), "Mechanical properties of recycled aggregate concrete under uniaxial loading", Cement Concrete Res., 35(6), 1187-1194. https://doi.org/10.1016/j.cemconres.2004.09.020.
  33. Xu, J.J., Chen, Z.P., Ozbakkaloglu, T., Zhao, X.Y. and Demartino, C. (2018), "A critical assessment of the compressive behavior of reinforced recycled aggregate concrete columns", Eng. Struct., 161(4), 161-175. https://doi.org/10.1016/j.engstruct.2018.02.003.
  34. Xu, J.J., Chen, Z.P., Zhao, X.Y., Demartino, C., Ozbakkaloglu, T. and Xue, J.Y. (2019), "Seismic performance of circular recycled aggregate concrete-filled steel tubular columns: FEM modelling and sensitivity analysis", Thin Wall. Struct., 141(8), 509-525. https://doi.org/10.1016/j.tws.2019.04.016.
  35. Yang, Y.F. and Han, L.H. (2006), "Experimental behavior of recycled aggregate concrete filled steel tubular columns", J. Constr. Steel. Res., 62(12), 1310-1324. https://doi.org/10.1016/j.jcsr.2006.02.010.
  36. Zhang, J.H., Liu, X.G., Wu, Z.Y., Yu, H.F. and Fang, Q. (2022), "Fracture properties of steel fiber reinforced concrete: Size effect study via mesoscale modelling approach", Eng. Fract. Mech., 260(2), 108193. https://doi.org/10.1016/j.engfracmech.2021.108193.
  37. Zhao, D.Z. (2003), "Study on mechanical properties of steel reinforced high strength concrete-filled steel tube composite columns", College of Civil Engineering and Water Conservancy, Dalian University of technology. (In Chinese)