Advances in concrete construction

  • 제13권1호
  • /
  • Pages.35-43
  • /
  • 2022
  • /
  • 2287-5301(pISSN)
  • /
  • 2287-531X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

An experimental and analytical study into the strength of hooked-end steel fiber reinforced HVFA concrete

  • Shariq, M. (Department of Civil Engineering, Z.H. College of Engineering and Technology, Aligarh Muslim University) ;
  • Pal, S. (Department of Civil Engineering, Delhi Technological University) ;
  • Chaubey, R. (Department of Civil Engineering, Gautam Budh University) ;
  • Masood, A. (Department of Civil Engineering, Z.H. College of Engineering and Technology, Aligarh Muslim University)
  • 투고 : 2020.04.08
  • 심사 : 2021.12.28
  • 발행 : 2022.01.25
⟨ 이전 논문 다음 논문 ⟩

초록

The experimental investigations into hooked-end round steel fibers (HSF) effect on the age-dependent strengths of high volume fly ash (HVFA) concrete is studied. The concrete was prepared with class F fly ash used as partial cement replacement varied from 0% to 70% on an equal weight basis. Two percentages of HSF (i.e., 0.5% and 1.5% by volume fraction) of 50 mm length were added in plain, and 50% fly ash concrete mixes. The compressive and flexural tensile strength was determined at 7, 28, 56, and 90 days. The strength results of fly ash concrete mixes with and without steel fibers were compared with the plain concrete strength. The test results indicated that the strength of fly ash concrete is comparable with the plain concrete strength and further increases with an increase in the percentage of steel fibers. The maximum flexure strength of HVFA concrete is found with 0.5% steel fibers. It is concluded that the HVFA concrete with steel fibers of 50 mm length can effectively be used in concrete construction. The analytical models are proposed to predict the age-dependent compressive and flexural tensile strength of HVFA concrete with and without HSF. The compressive and tensile strength of HVFA concrete with HSF can be predicted using these models when the 28-day compressive strength of plain concrete is known. The present study will be helpful in the design and construction of reinforced and pre-stressed concrete structures made with HVFA and HSF.

키워드

참고문헌

  1. Alberti, M.G., Enfedaque, A., Galvez, J.C., Canovas, M.F. and Osorio, I.R. (2014), "Polyolefin fiber-reinforced concrete enhanced with steel-hooked fibers in low proportions", Mater. Des., 60, 57-65. https://doi.org/10.1016/j.matdes.2014.03.050.
  2. Atis, C.D. and Karahan, O. (2009), "Properties of steel fibre reinforced fly ash concrete", Constr. Build. Mater., 23, 392-399. https://doi.org/10.1016/j.conbuildmat.2007.11.002.
  3. Chore, H.S. and Joshi, M.P. (2015), "Strength evaluation of concrete with fly ash and GGBFS as cement replacing materials", Adv. Concrete Constr., 3(3), 223-236. http://doi.org/10.12989/acc.2015.3.3.223.
  4. Colombo, M. and Felicetti, R. (2007), "New NDT techniques for the assessment of fire-damaged concrete structures", Fire Saf. J., 42, 461-472. https://doi.org/10.1016/j.firesaf.2006.09.002.
  5. Cunha, V.M., Barros, J.A. and Sena-Cruz, J.M. (2010), "Pullout behavior of steel fibers in self-compacting concrete", J. Mater. Civil Eng., 22(1), 1-9. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000001.
  6. Dong, S., Dong, X., Ashour, A., Han, B. and Ou, J. (2020), "Fracture and self-sensing characteristics of super-fine stainless wire reinforced reactive powder concrete", Cement Concrete Compos., 105, 103427. https://doi.org/10.1016/j.cemconcomp.2019.103427.
  7. Dong, S., Han, B., Yu, X. and Ou, J. (2019b), "Constitutive model and reinforcing mechanisms of uniaxial compressive property for reactive powder concrete with super-fine stainless wire", Compos. B Eng., 166, 298-309. https://doi.org/10.1016/j.compositesb.2018.12.015.
  8. Dong, S., Wang, Y., Ashour, A., Han, B. and Ou, J. (2021), "Uniaxial compressive fatigue behavior of ultra-high performance concrete reinforced with super-fine stainless wires", Int. J. Fatigue, 142, 105959. https://doi.org/10.1016/j.ijfatigue.2020.105959.
  9. Dong, S., Zhou, D., Ashour, A., Han, B. and Ou, J. (2019a), "Flexural toughness and calculation model of super-fine stainless wire reinforced reactive powder concrete", Cement Concrete Compos., 104, 103367. https://doi.org/10.1016/j.cemconcomp.2019.103367.
  10. Dragas, J., Tosic, N., Ignjatovic, I. and Marinkovic, S. (2016), "Mechanical and time-dependent properties of high-volume fly ash concrete for structural use", Mag. Concrete Res., 68(12), 632-645. https://doi.org/10.1680/jmacr.15.00384.
  11. Dura'n-Herrera, A., Jua'rez, C.A., Valdez, P. and Bentz, D.P. (2011), "Evaluation of sustainable high-volume fly ash concretes", Cement Concrete Compos., 33, 39-45. https://doi.org/10.1016/j.cemconcomp.2010.09.020.
  12. Faris, M.A., Abdullah, M.M.A.B., Muniandy, R., Abu Hashim, M.F., Bloch, K., Jez, B., Garus, S., Palutkiewicz, P., Mohd Mortar, N.A. and Ghazali, M.F. (2021), "Comparison of hook and straight steel fibers addition on Malaysian fly ash-based geopolymer concrete on the slump, density, water absorption and mechanical properties", Mater., 14(5), 1310. https://doi.org/10.3390/ma14051310.
  13. Feng, J., Sun, W.W., Wang, X.M. and Shi, X.Y. (2014), "Mechanical analyses of hooked fiber pullout performance in ultra-high-performance concrete", Constr. Build. Mater., 69, 403-410. https://doi.org/10.1016/j.conbuildmat.2014.07.049.
  14. Gholampour, A. and Ozbakkaloglu, T. (2017), "Performance of sustainable concretes containing very high volume class-F fly ash and ground granulated blast furnace slag", J. Clean. Prod., 162, 1407-1417. https://doi.org/10.1016/j.jclepro.2017.06.087.
  15. Goriparthi, M.R. and Rao, G.T.D. (2017), "Effect of fly ash and GGBS combination on mechanical and durability properties of GPC", Adv. Concrete Constr., 5(4), 313-330. https://doi.org/10.12989/acc.2017.5.4.313.
  16. Hashmi, A.F., Shariq, M. and Baqi, A. (2020), "Flexural performance of high volumefly ash reinforced concrete beams and slabs", Struct., 25, 868-880. https://doi.org/10.1016/j.istruc.2020.03.071.
  17. Hassan, A., Arif, M. and Shariq, M. (2019), "Effect of curing condition on the mechanical properties of fly ash-based geopolymer concrete", SN Appl. Sci., 1, 1694. https://doi.org/10.1007/s42452-019-1774-8.
  18. Huang, C., Lin, S., Chang, C. and Chen, H. (2013), "Mix properties and mechanical properties of concrete containing very high-volume of Class F flyash", Constr. Build. Mater., 46, 71-78. https://doi.org/10.1016/j.conbuildmat.2013.04.016.
  19. Ignjatovic, I., Sas, Z., Dragas, J., Somlai, J. and Kovacs, T. (2017), "Radiological and material characterization of high volume fly ash concrete", J. Env. Radioact., 168, 38-45. https://doi.org/10.1016/j.jenvrad.2016.06.021.
  20. Iqbal, S., Ali, I., Room, S., Khan, S.A. and Ali, A. (2019), "Enhanced mechanical properties of fiber reinforced concrete using closed steel fibers", Mater. Struct., 52(3), 56. https://doi.org/10.1617/s11527-019-1357-6.
  21. IS 10262 (2009), Recommended Guidelines for Concrete Mix Design, Bureau of Indian Standards, New Delhi, India.
  22. IS 2386 (1990), Methods of Test for Aggregates for Concrete, Bureau of Indian Standards, New Delhi, India.
  23. IS 3812 (part-1) (1999), Specification for Fly Ash for Use as Pozzolana and Admixture, Bureau of Indian Standards, New Delhi, India.
  24. IS 383 (2002), Specification for Coarse and Fine Aggregate from Natural Sources for Concrete (second revision), Bureau of Indian Standards, New Delhi, India.
  25. IS 4031 (1999), Methods of Physical Tests for Hydraulic Cement, Bureau of Indian Standards, New Delhi, India.
  26. IS 456 (2000), Plain and Reinforced Concrete-Code of Practice, Bureau of Indian Standards, New Delhi, India.
  27. IS 516 (2004), Methods of Tests for Strength of Concrete, Bureau of Indian Standards, New Delhi, India.
  28. IS 8112 (1989), 43 Grade Ordinary Portland Cement-Specifications, Bureau of Indian Standards, New Delhi, India.
  29. Mehta, P.K. (2004), "High-performance, high-volume fly ash concrete for sustainable development", Proceedings of International workshop on sustainable development and concrete technology, Ames.
  30. Mengxiao, S., Qiang, W. and Zhikai, Z. (2015), "Comparison of the properties between high-volume fly ash concrete and high-volume steel slag concrete under temperature matching curing condition", Constr. Build. Mater., 98, 649-655. https://doi.org/10.1016/j.conbuildmat.2015.08.134.
  31. Nikhil, T.R. (2014), "Use of high volume fly ash in concrete pavements for sustainable development", Int. J. Sci. Res., 3(1), 131-133. https://doi.org/10.15373/22778179/JAN2014/43
  32. Pajak, M. and Ponikiewski, T. (2013), "Flexural behavior of selfcompacting concrete reinforced with different types of steel fibers", Constr. Build. Mater., 47, 397-408. https://doi.org/10.1016/j.conbuildmat.2013.05.072.
  33. Pal, S., Shariq, M., Abbas, H. Pandit, A.K. and Masood, A. (2020), "Strength characteristics and microstructure of hooked-end steel fiber reinforced concrete containing fly ash, bottom ash and their combination", Const. Build. Mater., 247, 118530. https://doi.org/10.1016/j.conbuiltmat.2020.118530.
  34. Paliwal, G. and Maru, S. (2017), "Effect of fly ash and plastic waste on mechanical and durability properties of concrete", Adv. Concrete Constr., 5(6), 575-586. https://doi.org/10.12989/acc.2017.5.6.575.
  35. Parande, A.K. (2013), "Role of ingredients for high strength and high performance concrete-A review", Adv. Concrete Constr., 1(2), 151-162. http://doi.org/10.12989/acc.2013.1.2.151.
  36. Parveen and Singhal, D. (2017), "Development of mix design method for geopolymer concrete", Adv. Concrete Constr., 5(4), 377-390. https://doi.org/10.12989/acc.2017.5.4.377.
  37. Patel, I. and Modhera, C.D. (2010), "Study basic properties on fiber reinforced high volume fly ash concrete", J. Eng. Res. Stud., 9(9), 60-70.
  38. Patel, I. and Modhera, C.D. (2013), "Experimental investigation to study effect of polyester fiber on durability of HVFA concrete through RCPT", IOSR J. Eng., 3(6), 22-27. https://doi.org/10.9790/3021-03622227.
  39. Rashad, A.M. (2015), "A brief on high-volume Class F fly ash as cement replacement-A guide for Civil Engineer", Int. J. Sustain. Built. Env., 4, 278-306. https://doi.org/10.1016/j.ijsbe.2015.10.002.
  40. Robins, P., Austin, S. and Jones, P. (2002), "Pull-out behaviour of hooked steel fibres", Mater. Struct., 35(7), 434-442. https://doi.org/10.1007/BF02483148.
  41. Shaikh, F., Kerai, S. and Kerai, S. (2015), "Effect of micro-silica on mechanical and durability properties of high volume fly ash recycled aggregate concretes(HVFA-RAC)", Adv. Concrete Constr., 3(4), 317-331. https://doi.org/10.12989/acc.2015.3.4.317.
  42. Siddique, R. (2004), "Properties of concrete incorporating high volumes of class F fly ash and san fibers", Cement Concrete Res., 34, 37-42. https://doi.org/10.1016/S0008-8846(03)00192-3.
  43. Siddique, R. (2008), "Fracture toughness and impact strength of high volume Class-F fly ash concrete reinforced with natural san fibres", Leonardo Electron. J. Pract. Tech., 12, 25-36.
  44. Siddique, R., Kapoor, K., Kadri, V. and Bennacer, R. (2012), "Effect of polyester fibres on the compressive strength and abrasion resistance of HVFA concrete", Constr. Build. Mater., 29, 270-278. https://doi.org/10.1016/j.conbuildmat.2011.09.011.
  45. Sofi, A., Swathy, K. and Srija, G. (2013), "Toughness study on fly ash based fiber reinforced concrete", Int. J. Adv. Struct. Eng., 5(17), 1-4. https://doi.org/10.1186/2008-6695-5-17.
  46. Sounthararajan, V.M. and Sivakumar, A. (2013), "Performance evaluation of metallic fibers on the low and high volume Class F fly ash based cement concrete", Int. J. Eng. Tech., 5(2), 606-619.
  47. Wang, X.Y. and Park, K.B. (2015), "Analysis of compressive strength development of concrete containing high volume fly ash", Constr. Build. Mater., 98, 810-819. https://doi.org/10.1016/j.conbuildmat.2015.08.099.
  48. Wang, X.Y. and Park, K.B. (2016), "Analysis of compressive strength development and carbonation depth of high-volume fly ash cement pastes", ACI Mater. J., 113(2), 151-161.
  49. Zile, E. and Zile, O. (2013), "Effect of the fiber geometry on the pullout response of mechanically deformed steel fibers", Cement Concrete Res., 44, 18-24. https://doi.org/10.1016/j.cemconres.2012.10.014.