Steel and Composite Structures

  • 제42권2호
  • /
  • Pages.161-172
  • /
  • 2022
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Studies on CFST column to steel beam joints using endplates and long bolts under central column removal

  • Gao, Shan (Shaanxi Key Laboratory of safety and durability of concrete structures, Xijing University) ;
  • Yang, Bo (School of Civil Engineering, Chongqing University) ;
  • Guo, Lanhui (School of Civil Engineering, Harbin Institute of Technology) ;
  • Xu, Man (School of Civil Engineering, Northeast Forestry University) ;
  • Fu, Feng (School of Mathematics, Computer Science & Engineering, University of London)
  • 투고 : 2019.03.25
  • 심사 : 2021.12.24
  • 발행 : 2022.01.25
⟨ 이전 논문 다음 논문 ⟩

초록

In this paper, four specimens of CFST column joints with endplates and long bolts are tested in the scenario of progressive collapse. Flush endplate and extended endplate are both adopted in this study. The experimental results show that increasing the thickness of the endplate could improve the behavior of the joint, but delay the mobilization of catenary action. The thickness of the endplate should not be relatively thick in comparison to the diameter of the bolts, otherwise catenary action would not be mobilized or work effectively. Effective bending deformation of the endplate could help the formation and development of catenary action in the joints. The performance of flexural action in the joint would affect the formation of catenary action in the joint. Extra middle-row bolts set at the endplates and structural components set below the bottom beam flange should be used to enhance the robustness of joints. A special weld access hole between beam and endplate should be adopted to mitigate the chain damage potential of welds. It is suggested that the structural components of joints should be independent of each other to enhance the robustness of joints. Based on the component method, a formula calculating the stiffness coefficient of preloaded long bolts was proposed whose results matched well with the experimental results.

키워드

과제정보

The project is supported by National Natural Science Foundation of China (NO. 51908085), Natural Science Foundation of Chongqing (cstc2020jcyj-msxmX0010), Fundamental Research Funds for the Central Universities (2020CDJ-LHZZ-013), and the Youth Innovation Team of Shaanxi Universities (21JP138) which are gratefully acknowledged.

참고문헌

  1. Demonceau J.F. and Jaspart J.P. (2010), "Experimental test simulating a column loss in a composite frame", Adv. Steel Construct., 6, 891-913. http://hdl.handle.net/2268/30645.
  2. Department of Defense U.S. (2013), Unified Facilities Criteria: Design of Building to Resist Progressive Collapse, UFC 4-023-03, U.S.A.
  3. Elghazouli, A.Y., Magala-Chuquitaype, C., Castro J.M. and Orton A.H. (2009), "Experimental monotonic and cyclic behavior of blind-bolted angle connections", Eng. Struct., 31, 2540-2553. https://doi.org/10.1016/j.engstruct.2009.05.021.
  4. EN 1994-1-1, European Committee for Strandardization - CEN (2005), Eurocode 4: Design of Composite Seel and Concrete Structures. Part 1.1, General rules and rules for buildings, Brussels.
  5. EN1993-1-8, European Committee for Strandardization - CEN (2005), Eurocode 3: Design of Steel Structures. Part 1.8, Design of Joints, Brussels.
  6. Faella, C., Piluso, V. and Rizzano G. (1998), "Experimental analysis of bolted connections: snug versus preloaded bolts", J. Struct. Eng., 124, 764-744. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:7(765).
  7. Federal Emergency Management Agency (2000), FEMA-350: Recommended Seismic Design Criteria for New Steel Moment-Frame Buildings, U.S.A.
  8. Gao, S., Guo., Fu, F. and Zhang, S.M. (2017), "Capacity of semi-rigid composite joints in accommodating column loss", J. Constra. Steel Res., 139, 288-301. https://doi.org/10.1016/j.jcsr.2017.09.029.
  9. GB50017-2017 (2017), Code for Design of Steel Structures. Beijing, China.
  10. GB50936-2014 (2014), Technical Code for Concrete Filled Steel Tubular Structures. Beijing, China.
  11. General Services Administration U.S. (2003), Progressive Collapse Analysis and Design Guidelines for New Federal Office Buildings and Major Modernization Projects, Washington D.C.
  12. Hoang, V.L., Jaspart J.P. and Demonceau J.F. (2015), "Extended end-plate to concrete-filled rectangular column joint using long bolts", J. Construct. Steel Res., 113, 156-168. https://doi.org/10.1016/j.jcsr.2015.06.001.
  13. Hoffman, S.T. and Fahnestock, L.A. (2011), "Behavior of multi-story steel buildings under dynamic column loss scenarios", Steel Compos. Struct., 11(2), 149-168. https://doi.org/10.12989/scs.2011.11.2.149
  14. Huang, Z., Jiang, L.Z., Zhou, W.B. and Chen, S. (2016), "Studies on restoring force model of concrete filled steel tubular lace column to composite box-beam connections", Steel Compos. Struct., 22(6), 1217-1238. https://doi.org/10.12989/scs.2016.22.6.1217
  15. Izzuddin, B.A., Vlassis, A.G., Elghazouli, A.Y. and Nethercot, D.A. (2008), "Progressive collapse of multi-storey buildings due to sudden column loss-Part 1: Simplified assessment framework", Eng. Struct., 30(5), 1308-1318. https://doi.org/10.1016/j.engstruct.2007.07.011.
  16. Khaloo, A. and Omidi, H. (2018), "Evaluation of vierendeel peripheral frame as supporting structural element for prevention of progressive collapse", Steel Compos. Struct., 26(5), 549-556. https://doi.org/10.12989/scs.2018.26.5.549.
  17. Li, W. and Han, L.H. (2011), "Seismic performance of CFST column to steel beam joints with RC slab: Analysis", J. Constrcut. Steel Res., 67(1), 127-139. https://doi.org/10.1016/j.jcsr.2010.07.002.
  18. Mashhadi, J. and Saffari, H. (2017), "Dynamic increase factor based on residual strength to assess progressive collapse", Steel Compos. Struct., 25(5), 617-624. https://doi.org/10.12989/scs.2017.25.5.617.
  19. Mirtaheri, M. and Zoghi, M.A. (2016), "Design guides to resist progressive collapse for steel structures", Steel Compos. Struct., 20(2), 357-378. https://doi.org/10.12989/scs.2016.20.2.357.
  20. Sadek, F., Main, J.A., Lew, H.S. and Bao, Y.H. (2011), "Testing and analysis of steel and concrete beam-column assemblies under a column removal scenario", J. Struct. Eng., 9, 881-892. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000422.
  21. Simoes da Silva, L., Lima, L.R.O., Vellasco, P.C.G. and Andrade S.A.L. (2004), "Behaviour of flush end-plate beam-to-column joints under bending and axial force", Steel Compos. Struct., 4(2). 77-94. https://doi.org/10.12989/scs.2004.4.2.077
  22. Stylianidis, P.M. and Nethercot, D.A. (2015), "Modelling of connection behaviour for progressive collapse analysis", J. Constr. Steel Res., 113, 169-184. https://doi.org/10.1016/j.jcsr.2015.06.008.
  23. Tartaglia, R., D'Aniello, M., Zimbru, M. and Landolfo, R. (2018), "Finite element simulations on the ultimate response of extended stiffened end-plate joints", Steel Compos. Struct., 27(6), 727-745. https://doi.org/10.12989/scs.2018.27.6.727.
  24. Thai, H.T. and Uy, B. (2016), "Rotational stiffness and moment resistance of bolted endplate joints with hollow or CFST columns", J. Constr. Steel Res., 126, 139-152. https://doi.org/10.1016/j.jcsr.2016.07.005.
  25. Wang, J.F. and Chen, L.P. (2012), "Experimental investigation of extended end plate joints to concrete-filled steel tubular columns", J. Constr. Steel Res., 79, 56-70. https://doi.org/10.1016/j.jcsr.2012.07.016.
  26. Xu, M., Gao, S., Zhang, S. and Li, H. (2018), "Experimental study on bolted CFST-column joints with different configurations in accommodating column-loss", J. Constr. Steel Res., 151, 122-131. https://doi.org/10.1016/j.jcsr.2018.09.021.
  27. Yang, B. and Tan, K.H. (2012), "Numeircal analyses of steel beam-column joints subjected to catenary action", J. Constr. Steel Res., 70, 1-11. https://doi.org/10.1016/j.jcsr.2011.10.007.