Geomechanics and Engineering

  • 제28권2호
  • /
  • Pages.117-133
  • /
  • 2022
  • /
  • 2005-307X(pISSN)
  • /
  • 2092-6219(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

2D numerical study of the mechanical behaviour of non-persistent jointed rock masses under uniaxial and biaxial compression tests

  • 투고 : 2021.05.17
  • 심사 : 2021.12.01
  • 발행 : 2022.01.25
⟨ 이전 논문 다음 논문 ⟩

초록

Determination of the mechanical behaviour of jointed rock masses has been a challenge for rock engineers for decades. This problem is more pronounced for non-persistent jointed rock masses due to complicated interaction of rock bridges on the overall behaviour. This paper aims to study the effect of a non-persistent joint set configuration on the mechanical behaviour of rock materials under both uniaxial and biaxial compression tests using a discrete element code. The numerical simulation of biaxial compressive strength of rock masses has been challenging in the past due to shortcomings of bonded particle models in reproducing the failure envelope of rock materials. This problem was resolved in this study by employing the flat-joint contact model. The validity of the numerical model was investigated through a comprehensive comparative study against physical uniaxial and biaxial compression experiments. Good agreement was found between numerical and experimental tests in terms of the recorded peak strength and the failure mode in both loading conditions. Studies on the effect of joint orientation on the failure mode showed that four zones of intact, transition to block rotation, block rotation and transition to intact failure occurs when the joint dip angle varies from 0° to 90°. It was found that the applied confining stress can significantly alter the range of these zones. It was observed that the minimum strength occurs at the joint dip angle of around 45 degrees under different confining stresses. It was also found that the joint orientation can alter the post peak behaviour and the lowest brittleness was observed at the block rotation zone.

키워드

참고문헌

  1. Asadizadeh, M., Moosavi M. and Hossaini M.F. (2018), "Investigation of mechanical behaviour of non-persistent jointed blocks under uniaxial compression", Geomech. Eng., 14(1), 29-42. http://doi.org/10.12989/gae.2018.14.1.029.
  2. Bahaaddini, M. (2014), "Numerical study of the mechanical behaviour of rock joints and non-persistent jointed rock masses", Ph.D. thesis, University of New South Wales, Australia.
  3. Bahaaddini, M. and Rahimi, M. (2018), "Distinct element modelling of the mechanical behaviour of intact rocks using voronoi tessellation model", Int. J. Min. Geo-Eng., 52(1), 61-68. https://doi.org/10.22059/ijmge.2017.240741.594694.
  4. Bahaaddini, M., Hagan, P.C. Mitra, R. and Hebblewhite, B.K. (2015), "Parametric study of smooth joint parameters on the shear behaviour of rock joints", Rock Mech. Rock Eng., 48, 923-940. https://doi.org/10.1007/s00603-014-0641-6.
  5. Bahaaddini, M., Sharrock, G. and Hebblewhite, B.K. (2011), "A comparison of physical and numerical experiments on artificial jointed rock masses using PFC3D", Proceedings of the 2th International FLAC/DEM Symposium, Melbourne, Australia.
  6. Bahaaddini, M., Sharrock, G. and Hebblewhite, B.K. (2013), "Numerical investigation of the effect of joint geometrical parameters on the mechanical properties of a non-persistent jointed rock mass under uniaxial compression", Comput. Geotech., 49, 206-225. https://doi.org/10.1016/j.compgeo.2012.10.012.
  7. Bahaaddini, M., Sharrock, G., Hebblewhite, B.K. and Mitra, R. (2012a), "Direct shear tests to model the shear behavior of rock joints by PFC2D", Proceedings of the 46th US Rock Mechanics/Geomechanics Symposium, American Rock Mechanics Association.
  8. Bahaaddini, M., Sharrock, G., Hebblewhite, B.K. and Mitra, R. (2012b), "Statistical analysis of the effect of joint geometrical parameters on the mechanical properties of non-persistent jointed rock masses", Proceedings of the 46th US Rock Mechanics/Geomechanics Symposium, Chicago, USA, American Rock Mechanics Association.
  9. Bahaaddini, M., Sheikhpourkhani, A.M. and Mansouri, H. (2019), "Flat-joint model to reproduce the mechanical behaviour of intact rocks", Eur. J. Environ. Civil Eng., 1-22. https://doi.org/10.1080/19648189.2019.1579759.
  10. Bobet, A. and Einstein, H.H. (1998), "Fracture coalescence in rock-type materials under uniaxial and biaxial compression", Int. J. Rock Mech. Min. Sci., 35(7), 863-888. https://doi.org/10.1016/S0148-9062(98)00005-9.
  11. Brown, E.T. (2008), "Estimating the mechanical properties of rock masses", Paper presented at the Proceedings of the First Southern Hemisphere International Rock Mechanics Symposium, Perth, 16-19. September.
  12. Cao, R.H. and Lin, H. (2017), "Experimental and numerical study of failure behavior and energy mechanics of rock-like materials containing multiple joints", Adv. Mater. Sci. Eng., 2017, https://doi.org/10.1155/2017/6460150.
  13. Chen, X., Liao, Z. and Peng, X. (2012), "Deformability characteristics of jointed rock masses under uniaxial compression", Int. J. Min. Sci. Technol., 22(2), 213-221. https://doi.org/10.1016/j.ijmst.2011.08.012.
  14. Cho, N., Martin, C.D. and Sego, D.C. (2007), "A clumped particle model for rock", Int. J. Rock Mech. Min. Sci., 44(7), 997-1010. https://doi.org/10.1016/j.ijrmms.2007.02.002.
  15. Cording, E. and Jamil, M. (1997), "Slide geometries on rock slopes and walls", Proceedings of the 4th South American Congress on Rock Mechanics, Santiago.
  16. Cundall, P.A. (2000), "Numerical experiments on rough joints in shear using a bonded particle model", Proceedings of the Aspects of Tectonic Faulting: In Honour of Georg Mandl, Springer Berlin Heidelberg, Berlin, Heidelberg, https://doi.org/10.1007/978-3-642-59617-9_1.
  17. Elmo, D., Donati, D. and Stead, D. (2018), "Challenges in the characterisation of intact rock bridges in rock slopes", Eng. Geology, 245, 81-96. https://doi.org/10.1016/j.enggeo.2018.06.014.
  18. Fan, X., Kulatilake, P.H.S.W. and Chen, X. (2015), "Mechanical behavior of rock-like jointed blocks with multi-non-persistent joints under uniaxial loading: a particle mechanics approach", Eng. Geology, 190, 17-32. https://doi.org/10.1016/j.enggeo.2015.02.008.
  19. Han, G., Jing, H., Jiang, Y., Liu, R., Su, H. and Wu, J. (2018), "The effect of joint dip angle on the mechanical behavior of infilled jointed rock masses under uniaxial and biaxial compressions", Processes, 6(5), 49. https://doi.org/10.3390/pr6050049.
  20. Itasca Consulting Group. Inc, (2015), "PFC (particle flow code is 2 and 3 dimensions)", version 5 user's manual, Minneapolis, Minnesota.
  21. Jamil, S.M. (1992), "Strength of non-persistent rock joints", PhD Thesis, University of Illinois.
  22. Jennings, J. (1970), "A mathematical theory for the calculation of the stability of slopes in open cast mines", In: Planning Open Pit Mines, Proceedings, Johannesburg, AA Balkema Cape Town, 21, 87-102.
  23. Kachanov, M. (1987), "Elastic solids with many cracks: a simple method of analysis", Int. J. Solid. Struct., 23(1), 23-43. https://doi.org/10.1016/0020-7683(87)90030-8.
  24. Mas Ivars, D., Pierce, M.E., Darcel, C., Reyes-Montes, J., Potyondy, D.O., Paul Young, R. and Cundall, P.A. (2011), "The synthetic rock mass approach for jointed rock mass modelling", Int. J. Rock Mech. Min. Sci., 48(2), 219-244. https://doi.org/10.1016/j.ijrmms.2010.11.014.
  25. Mughieda, O.S. (1997), "Failure mechanisms and strength of non-persistent rock joints", PhD Thesis, University of Illinois.
  26. Park, C.H. and Bobet, A. (2009), "Crack coalescence in specimens with open and closed flaws: A comparison", Int. J. Rock Mech. Min. Sci., 46(5), 819-829. https://doi.org/10.1016/j.ijrmms.2009.02.006.
  27. Park, C.H. and Bobet, A. (2010), "Crack initiation, propagation and coalescence from frictional flaws in uniaxial compression", Eng. Fract. Mech., 77(14), 2727-2748. https://doi.org/10.1016/j.engfracmech.2010.06.027.
  28. Pierce, M., Cundall, P.A. Potyondy, D.O. and Mas Ivars, D. (2007), "A synthetic rock mass model for jointed rock", In: Rock mechanics: meeting society's challenges and demands, 341-349.
  29. Potyondy, D.O. (2011), "Parallel-bond refinements to match macroproperties of hard rock", Proceedings of the 2nd International FLAC/DEM Symposium: Continuum and distinct element modeling in Geomechanics.
  30. Potyondy, D.O. (2012), "A flat-jointed bonded-particle material for hard rock", Proceedings of the 46th US rock mechanics/geomechanics symposium, American Rock Mechanics Association.
  31. Potyondy, D.O. (2015), "The bonded-particle model as a tool for rock mechanics research and application: current trends and future directions", Geosyst. Eng., 18(1), 1-28. https://doi.org/10.1080/12269328.2014.998346.
  32. Potyondy, D.O. and Cundall, P.A. (2004), "A bonded-particle model for rock", Int. J. Rock Mech. Min. Sci., 41(8), 1329-1364. https://doi.org/10.1016/j.ijrmms.2004.09.011.
  33. Prudencio, M. (2009), "Study of the strength and failure mode of rock mass with non-persistent joints", PhD Thesis, Catholic University of Chile.
  34. Prudencio, M. and Van Sint Jan, M. (2007), "Strength and failure modes of rock mass models with non-persistent joints", Int. J. Rock Mech. Min. Sci., 44(6), 890-902. https://doi.org/10.1016/j.ijrmms.2007.01.005.
  35. Renani, H.R., Martin, C.D. and Cai, M. (2019), "An analytical model for strength of jointed rock masses", Tunn. Undergr. Sp. Tech., 94, 103159. https://doi.org/10.1016/j.tust.2019.103159.
  36. Shemirani, A.B., Haeri H., Sarfarazi V. and Hedayat A. (2017), "A review paper about experimental investigations on failure behaviour of non-persistent joint", Geomech. Eng., 13(4), 535-570. http://doi.org/10.12989/gae.2017.13.4.535.
  37. Tian, W.L. and Yang S.Q. (2017), "Experimental and numerical study on the fracture coalescence behavior of rock-like materials containing two non-coplanar filled fissures under uniaxial compression", Geomech. Eng., 12(3), 541-560. http://doi.org/10.12989/gae.2017.12.3.541.
  38. Vergara, M.R., Jan, M.V.S. and Lorig, L. (2016), "Numerical model for the study of the strength and failure modes of rock containing non-persistent joints", Rock Mech. Rock Eng., 49, 1211-1226. https://doi.org/10.1007/s00603-015-0824-9.
  39. Wong, R.H. and Chau, K. (1998), "Crack coalescence in a rocklike material containing two cracks", Int. J. Rock Mech. Min. Sci., 35(2), 147-164. https://doi.org/10.1016/S0148-9062(97)00303-3.
  40. Wu, S. and Xu, X. (2016), "A study of three intrinsic problems of the classic discrete element method using flat-joint model", Rock Mech. Rock Eng., 49, 1813-1830. https://doi.org/10.1007/s00603-015-0890-z.
  41. Yang, S.Q. and Jing, H.W. (2011), "Strength failure and crack coalescence behavior of brittle sandstone samples containing a single fissure under uniaxial compression", Int. J. Fracture, 168, 227-250. https://doi.org/10.1007/s10704-010-9576-4.
  42. Yang, S.Q., Huang, Y.H. and Ranjith, P. (2018), "Failure mechanical and acoustic behavior of brine saturated-sandstone containing two pre-existing flaws under different confining pressures", Eng. Fract. Mech., 193, 108-121. https://doi.org/10.1016/j.engfracmech.2018.02.021.
  43. Yang, X.X., Jing, H.W. Tang, C.A. and Yang, S.Q. (2017), "Effect of parallel joint interaction on mechanical behavior of jointed rock mass models", Int. J. Rock Mech. Min. Sci., 92, 40-53. https://doi.org/10.1016/j.ijrmms.2016.12.010.
  44. Yin, P., Wong, R. and Chau, K. (2014), "Coalescence of two parallel pre-existing surface cracks in granite", Int. J. Rock Mech. Min. Sci., 68, 66-84. https://doi.org/10.1016/j.ijrmms.2014.02.011.
  45. Zhang, Y., Jiang, Y., Shi, X., Yin, Q. and Chen, M. (2020), "Shear failure and mechanical behavior of flawed specimens containing opening and joints", Geomech. Eng., 23(6), 587-600. http://doi.org/10.12989/gae.2020.23.6.587.
  46. Zhao, W., Huang, R. and Yan, M. (2015), "Mechanical and fracture behavior of rock mass with parallel concentrated joints with different dip angle and number based on PFC simulation", Geomech. Eng., 8(6), 757-767. http://dx.doi.org/10.12989/gae.2015.8.6.757.
  47. Zhou, C., Xu, C., Karakus, M. and Shen, J. (2018), "A systematic approach to the calibration of micro-parameters for the flat-jointed bonded particle model", Geomech. Eng., 16(5), 471-482. http://doi.org/10.12989/gae.2018.16.5.471.