Geomechanics and Engineering

  • 제28권1호
  • /
  • Pages.25-33
  • /
  • 2022
  • /
  • 2005-307X(pISSN)
  • /
  • 2092-6219(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Dynamic response of free-end rod with consideration of wave frequency

  • Kim, Sang Yeob (Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign) ;
  • Lee, Jong-Sub (School of Civil, Environmental and Architectural Engineering, Korea University) ;
  • Tutumluer, Erol (Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign) ;
  • Byun, Yong-Hoon (School of Agricultural Civil & Bio-Industrial Engineering, Kyungpook National University)
  • 투고 : 2021.07.22
  • 심사 : 2021.11.23
  • 발행 : 2022.01.10
⟨ 이전 논문 다음 논문 ⟩

초록

The energy transferred on drill rods by dynamic impact mainly determines the penetration depth for in-situ tests. In this study, the dynamic response and transferred energy of drill rods are determined from the frequency of the stress waves. AW-type drill rods of lengths 1 to 3 m are prepared, and strain gauges and an accelerometer are installed at the head and tip of the connected rods. The drill rods are hung on strings, allowing free vibration, and then impacted by a pendulum hammer with fixed potential energy. Increasing the rod length L increases the wave roundtrip time (2L/c, where c is the wave velocity), and hence the transferred energy at the rod head. At the rod tip, the first velocity peak is higher than the first force peak because a large and tensile stress wave is reflected, and the transferred energy converges to zero. The resonant frequency increases with rod length in the waveforms measured by the strain gauges, and fluctuates in the waveforms measured by the accelerometer. In addition, the dynamic response and transferred energy are perturbed when the cutoff frequency is lower than 2 kHz. This study implies that the resonant frequency should be considered for the interpretation of transferred energy on drill rods.

키워드

과제정보

This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIT) (No. NRF-2021R1A5A1032433).

참고문헌

  1. Abou-matar, H. and Goble, G.G. (2004), "SPT dynamic analysis and measurements", In Current Practices and Future Trends in Deep Foundations, 441-462.
  2. ASTM D1586 (2011), Test Method for Standard Penetration Test (SPT) and Split-Barrel Sampling of Soils; ASTM International: West Conshohocken, PA, USA. https://doi.org/10.1520/d1586-11
  3. ASTM D4633 (2011), Standard Test Method for Energy Measurement for Dynamic Penetrometers, ASTM International, West Conshohocken, PA, USA.
  4. ASTM D6951 (2011), Standard Test Method for Use of the Dynamic Cone Penetrometer in Shallow Pavement Applications, ASTM International, West Conshohocken, PA, USA.
  5. Bajaj, K. and Anbazhagan, P. (2019), "Seismic site classification and correlation between VS and SPT-N for deep soil sites in Indo-Gangetic Basin", Appl. Geophys., 163, 55-72. https://doi.org/10.1016/j.jappgeo.2019.02.011.
  6. Byun, Y.H. and Lee, J.S. (2013), "Instrumented dynamic cone penetrometer corrected with transferred energy into a cone tip: a laboratory study", Geotech. Test. J., 36(4), 533-542. https://doi.org/10.1520/gtj20120115.
  7. Byun, Y.H., Yoon, H.K., Kim, Y.S., Hong, S.S. and Lee, J.S. (2014), "Active layer characterization by instrumented dynamic cone penetrometer in Ny-Alesund, Svalbard", Cold Reg. Sci. Technol., 104, 45-53. https://doi.org/10.1016/j.coldregions.2014.04.003.
  8. Daniel, C.R., Howie, J.A., Jackson, R.S. and Walker, B. (2005), "Review of standard penetration test short rod corrections", J. Geotech. Geoenviron. Eng., 131(4), 489-497. https://doi.org/10.1061/(asce)1090-0241(2005)131:4(489).
  9. Du, Y.J., Jiang, N.J., Liu, S.Y., Horpibulsuk, S. and Arulrajah, A. (2016), "Field evaluation of soft highway subgrade soil stabilized with calcium carbide residue", Soils Found., 56, 301-314. https://doi.org/10.1016/j.sandf.2016.02.012
  10. Gabr, M.A., Hopkins, K., Coonse, J. and Hearne, T. (2000), "DCP criteria for performance evaluation of pavement layers", J. Perform. Constr. Fac., 14(4), 141-148. https://doi.org/10.1061/(asce)0887-3828(2000)14:4(141)
  11. Hong, W.T., Byun, Y.H., Kim, S.Y. and Lee, J.S. (2016), "Cone penetrometer incorporated with dynamic cone penetration method for investigation of track substructures", Smart Struct. Syst., 18(2), 197-216. https://doi.org/10.12989/sss.2016.18.2.197.
  12. Howie, J.A., Daniel, C.R., Jackson, R.S. and Walker, B. (2003), "Comparison of energy measurement methods in the standard penetration test", Report prepared for the US Bureau of Reclamation, Geotechnical Research Group, Department of Civil Engineering, The University of British Columbia, Vancouver, Canada.
  13. Kim, S.Y., Hong, W.T. and Lee, J.S. (2019), "Role of the coefficient of uniformity on the California bearing ratio, penetration resistance, and small strain stiffness of coarse arctic soils", Cold Reg. Sci. Technol., 160, 230-241. https://doi.org/10.1016/j.coldregions.2019.02.012
  14. Kim, S.Y. and Lee, J.S. (2020), "Energy correction of dynamic cone penetration index for reliable evaluation of shear strength in frozen sand-silt mixtures", Acta Geotech., 15(4), 947-961. https://doi.org/10.1007/s11440-019-00812-y.
  15. Kleyn, E.G. (1975), "The Use of the Dynamic Cone Penetrometer (DCP)", Transvaal Roads Department, Report Number L2/74, Pretoria.
  16. Kovacs, W.D. (1979), "Velocity measurement of free-fall SPT hammer", J. Geotech. Geoenviron. Eng., 105(1), 1-10. https://doi.org/10.1061/ajgeb6.0000748.
  17. Kodicherla, S.P.K. and Nandyala, D.K. (2016), "Use of CPT and DCP based correlations in characterization of subgrade of a highway in Southern Ethiopia Region", Int. J. Geo-Eng., 7(1), 1-15. https://doi.org/ 10.1186/s40703-016-0025-8.
  18. Langton, D.D. (1999), "The Panda lightweight penetrometer for soil investigation and monitoring material compaction", Ground Engineering.
  19. Lee, C., Lee, J.S., An, S. and Lee, W. (2010), "Effect of secondary impacts on SPT rod energy and sampler penetration", J. Geotech. Geoenviron. Eng., 136(3), 522-526. https://doi.org/10.1061/(asce)gt.1943-5606.0000236.
  20. Lee, J.S. and Byun, Y.H. (2020), "Instrumented cone penetrometer for dense layer characterization", Sensors, 20(20), 5782. https://doi.org/10.3390/s20205782.
  21. Lee, J.S., Kim, S.Y., Hong, W.T. and Byun, Y.H. (2019), "Assessing subgrade strength using an instrumented dynamic cone penetrometer", Soils Found., 59(4), 930-941. https://doi.org/10.1016/j.sandf.2019.03.005.
  22. Mir, M., Bouafia, A., Rahmani, K. and Aouali, N. (2017), "Analysis of load-settlement behaviour of shallow foundations in saturated clays based on CPT and DPT tests", Geomech. Eng., 13(1), 119-139. https://doi.org/10.12989/gae.2017.13.1.119.
  23. Mohammadi, S.D., Nikoudel, M.R., Rahimi, H. and Khamehchiyan, M. (2008), "Application of the Dynamic Cone Penetrometer (DCP) for determination of the engineering parameters of sandy soils", Eng. Geol., 101(3-4), 195-203. https://doi.org/10.1016/j.enggeo.2008.05.006.
  24. Morgano, C.M. and Liang, R. (1992), "Energy transfer in SPT-Rod length effect", In International conference on the application of stress-wave theory to piles, 121-127.
  25. Odebrecht, E., Schnaid, F., Rocha, M.M. and de Paula Bernardes, G. (2005), "Energy efficiency for standard penetration tests", J. Geotech. Geoenviron. Eng., 131(10), 1252-1263. https://doi.org/10.1061/(asce)1090-0241(2005)131:10(1252).
  26. Sancio, R.B. and Bray, J.D. (2005), "An assessment of the effect of rod length on SPT energy calculations based on measured field data", Geotech. Test. J., 28(1), 22-30. https://doi.org/10.1520/gtj11959.
  27. Scala, A.J. (1956), "Simple methods of flexible pavement design using cone penetrometers", New Zealand Eng., 11(2), 34-44.
  28. Seed, H.B., Tokimatsu, K., Harder, L.F. and Chung, R.M. (1985), "Influence of SPT procedures in soil liquefaction resistance evaluations", J. Geotech. Eng., 111(12), 1425-1445. https://doi.org/10.1061/(asce)0733-9410(1985)111:12(1425).
  29. Skempton, A.W. (1986), "Standard penetration test procedures and the effects in sands of overburden pressure, relative density, particle size, ageing and overconsolidation", Geotechnique, 36(3), 425-447. https://doi.org/10.1680/geot.1986.36.3.425.
  30. Sujatha, E.R., Geetha, A.R., Jananee, R. and Karunya, S.R. (2018), "Strength and mechanical behaviour of coir reinforced lime stabilized soil", Geomech. Eng., 16(6), 627-634. https://doi.org/10.12989/gae.2018.16.6.627.
  31. Webster, S.L., Grau, R.H. and Williams, T.P. (1992), "Description and Application of Dual Mass Dynamic Cone Penetrometer", Instruction Report GL-92-3, Department of the Army, US Army Corp of Engineers, Washington, DC.
  32. Youd, T.L. and Idriss, I.M. (2001), "Liquefaction resistance of soils: summary report from the 1996 NCEER and 1998 NCEER/NSF workshops on evaluation of liquefaction resistance of soils", J. Geotech. Geoenviron. Eng., 127(4), 297-313. https://doi.org/10.1061/(asce)1090-0241(2001)127:4(297).
  33. Sy, A. and Campanella, R.G. (1993), "Standard penetration test energy measurements using a system based upon the personal computer", Can. Geotech. J., 30, 876-882. https://doi.org/10.1139/t93-078