Computers and Concrete

  • 제28권4호
  • /
  • Pages.369-378
  • /
  • 2021
  • /
  • 1598-8198(pISSN)
  • /
  • 1598-818X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

A hybrid artificial neural network-based identification system for fine-grained composites

  • 투고 : 2020.10.01
  • 심사 : 2021.10.23
  • 발행 : 2021.10.25
⟨ 이전 논문 다음 논문 ⟩

초록

Recent interest in the development of innovative building materials has brought about the need for a detailed assessment of their mechanical fracture properties. The parameters for these need to be acquired, and one of the possible ways of doing so is to obtain them indirectly - based on a combination of fracture testing and inverse analysis. The paper describes a method for the identification of selected parameters of mortars and other fine-grained brittle matrix composites. The cornerstone of the method is the use of an artificial neural network, which is utilized as a surrogate model of the inverse relation between the measured specimen response parameters and the sought material parameters. Due to the potentially wide range of composite mixtures and hence the wide range of experimental responses likely to be gained from individual specimens, an ensemble of artificial neural networks was created. It allows the entire range of variants to be covered and provides resulting parameter values with sufficient precision. Such a system is also easy to expand if a composite with properties outside the current range is tested. The capabilities of the proposed identification system are demonstrated on two selected types of fine-grained composites with different specimen responses. The first group of specimens was made of composite based on alkali-activated slag with standardized and natural sand investigated within the time interval of 3 to 330 days of aging. The second tested composite contained alkali-activated fly ash matrix, and the effect of the addition of natural fibers on fracture response was investigated.

키워드

과제정보

The authors would like to express their thanks for the support provided from the Czech Science Foundation project MUFRAS No. 19-09491S and the specific university research project No. FAST-J-20-6413 granted by Brno University of Technology. We also address special thanks to Barbara Kucharczykova from Brno University of Technology for conducting the fracture tests whose results were used in the applications section of this paper.

참고문헌

  1. Bui, H.D. (1997), "Inverse problems in the mechanics of materials", Editions of the University of Karadanga.
  2. Cervenka, V., Jendele, L. and Cervenka, J. (2000), "ATENA Program Documentation-Part 1", Cervenka Consulting sro.
  3. Cochocki, A. and Unbehauen, R. (1993), Neural Networks for Optimization and Signal Processing, John Wiley and Sons, Inc..
  4. Cincotto, M.A., Melo, A.A. and Repette, W.L. (2003), "Effect of different activators type and dosages and relation with autogenous shrinkage of activated blast furnace slag cement", Proceedings of 11th International Congress on the Chemistry of Cement, 1878-1888, Durban, May.
  5. Daskiran, E.G., Daskiran, M.M. and Gencoglu, M. (2016), "Development of fine grained concretes for textile reinforced cementitious composites", Comput. Concrete, 18(2), 279-295. https://doi.org/10.12989/cac.2016.18.2.279.
  6. Durrett, R. (2010), Probability: Theory and Examples, Cambridge University Press, New York.
  7. Hordijk, D.A. (1991), "Local approach to fatigue of concrete", Ph.D. Dissertation of Philosophy, Delft University of Technology.
  8. Karihaloo, B.L. (1995), Fracture Mechanics and Structural Concrete, Longman Scientific and Technical, New York, USA.
  9. Lehky, D., Kersner, Z. and Novak, D. (2014), "FraMePID-3PB software for material parameters identification using fracture test and inverse analysis", Adv. Eng. Softw., 72, 147-154. https://doi.org/10.1016/j.advengsoft.2013.10.001.
  10. Lehky, D. and Somodikova, M. (2017), "Reliability calculation of time-consuming problems using a small sample artificial neural network-based response surface method", Neur. Comput. Appl., 28(6), 1249-1263. https://doi.org/10.1007/s00521-016-2485-3.
  11. Li, B., Chen, M. Cheng, F. and Liu, L. (2004), "The mechanical properties of polypropylene fiber reinforced concrete", J. Wuhan Univ. Tech. Mater. Sci. Ed., 19(3), 68-71. https://doi.org/10.1007/BF02835065.
  12. Maier, G., Bocciarelli, M., Bolzon, G. and Fedele, R. (2006), "Inverse analyses in fracture mechanics", Int. J. Fract., 138(1), 47-73. https://doi.org/10.1007/s10704-006-7153-7.
  13. McKay, M.D., Beckman, R.J. and Conover, W.J. (2000), "A comparison of three methods for selecting values of input variables in the analysis of output from a computer code", Technometrics, 42(1), 55-61. https://doi.org/10.1080/00401706.2000.10485979
  14. Menetrey, P. and Willam K.J. (1995), "Triaxial failure criterion for concrete and its generalization", ACI Struct. J., 92(3), 311-318.
  15. Nedeljkovic, M., Lukovic, M., Van Breguel, K., Hordijk, D. and Ye, G. (2018), "Development and application of an environmentally friendly ductile alkali-activated composite", J. Clean. Prod., 180, 524-538. https://doi.org/10.1016/j.jclepro.2018.01.162.
  16. Novak, D. and Lehky, D. (2006), "ANN inverse analysis based on stochastic small-sample training set simulation", Eng. Appl. Artif. Intel., 19(7), 731-740. https://doi.org/10.1016/j.engappai.2006.05.003.
  17. Novak, D., Vorechovsky, M. and Teply, B. (2014), "FReET: Software for the statistical and reliability analysis of engineering problems and FReET-D: Degradation module", Adv. Eng. Softw., 72, 179-192. https://doi.org/10.1016/j.advengsoft.2013.06.011.
  18. Provis, J.L. and Van Deventer, J.S. (2013), Alkali Activated Materials: State-of-the-Art Report, RILEM TC 224-AAM, 13, Springer Science and Business Media.
  19. Ravikumar, C.S., Ramasamy, V. and Thandava-Moorthy, T.S. (2015), "Effect of fibres in concrete composites", Int. J. Appl. Eng. Res., 10(1), 419-430.
  20. Recommendation, R.D. (1985), "Determination of the fracture energy of mortar and concrete by means of three-point bend tests on notched beams", Mater. Struct., 18(106), 285-290. https://doi.org/10.1007/BF02472917
  21. Stavroulakis, G.E. (2001), Inverse and Crack Identification Problems in Engineering Mechanics, Springer Science and Business Media.
  22. Stebbings, T.F., Chandler, H.W., Henderson, R.J. and MacPhee, D.E. (2002), "Enhancing the toughness of high performance cement systems", Innov. Dev. Concrete Mater. Constr., 269-279.
  23. Simonova, H., Dragas, J., Kucharczykova, B., Kersner, Z., Ignjatovic, I., Komljenovic, M. and Nikolic, V. (2018), "Fracture Behaviour of Geopolymer Mortars Reinforced with Hemp Fibres", fib 2018-Better, Smarter, Stronger, 13, 583-578.
  24. Simonova, H., Kucharczykova, B., Bilek, V., Jr. and Kocab, D. (2020), "Mechanical fracture characterization of alkali-activated slag mortars with standardized and natural sand", MATEC Web of Conferences, SPACE 2019, 310, 00021. https://doi.org/10.1051/matecconf/202031000021.
  25. Ye, H., Cartwright, CH., Rajabipour, F. and Radlinska, A. (2017), "Understanding the drying shrinkage performance of alkali-activated slag mortars", Cement Concrete Compos., 76, 13-24. https://doi.org/10.1016/j.cemconcomp.2016.11.010.
  26. Zhou, Z.H., Wu, J. and Tang, W. (2002), "Ensembling neural networks: many could be better than all", Artif. Intel., 137(1-2), 239-263. https://doi.org/10.1016/S0004-3702(02)00190-X.
  27. Zimmermann, T., Strauss, A., Lehky, D., Novak, D. and Kersner, Z. (2014), "Stochastic fracture-mechanical characteristics of concrete based on experiments and inverse analysis", Constr. Build. Mater., 73, 535-543. https://doi.org/10.1016/j.conbuildmat.2014.09.087.
  28. Zimmermann, T. and Lehky, D. (2015), "Fracture parameters of concrete C40/50 and C50/60 determined by experimental testing and numerical simulation via inverse analysis", Int. J. Fract., 192(2), 179-189. https://doi.org/10.1007/s10704-015-9998-0.