Smart Structures and Systems

  • 제28권4호
  • /
  • Pages.567-578
  • /
  • 2021
  • /
  • 1738-1584(pISSN)
  • /
  • 1738-1991(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

A hybrid nondestructive testing method for detecting cavities behind the retaining wall

  • Yu, Jung-Doung (School of Civil, Environmental, and Architectural Engineering, Korea University) ;
  • Lee, Jong-Sub (School of Civil, Environmental, and Architectural Engineering, Korea University) ;
  • Kim, Hyun-Ki (Department of Civil and Environmental Engineering, Kookmin University)
  • 투고 : 2021.02.10
  • 심사 : 2021.09.06
  • 발행 : 2021.10.25
⟨ 이전 논문 다음 논문 ⟩

초록

This study proposes a combination of nondestructive testing methods for detecting soil cavities behind retaining walls, which adversely affect the stability of the sloping ground or retaining structures. An experimental study is conducted using a soil chamber filled with dry sands retained by a concrete wall plate. A hemispherical soil cavity is simulated just behind the wall plate, and elastic wave reflections of impacts on the wall are measured using accelerometers. The measured elastic waves are analyzed using the signal energy in time domain and predominant frequency and mobility spectrum in frequency domain. In addition, spatiotemporal changes in the surface of the wall during heating and cooling sequences are monitored using infrared thermography. The captured thermal image is then used for identifying the cavity. Experimental results show that the cavity leads to increases in the signal energy, predominant frequency, and flexibility in the mobility spectrum. The contrasts in the thermal images effectively reveal the shapes and locations of the soil cavity. This study demonstrates that the hybrid testing method that conducts a careful inspection by elastic waves on areas suspected in the preliminary scanning by the infrared thermography can be competitive and effective for detecting soil cavities.

키워드

과제정보

This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIT) (No. 2019R1A2C1088527).

참고문헌

  1. Al-Kassir, A.R., Fernandez, J., Tinaut, F. and Castro, F. (2005), "Thermographic study of energetic installations", Appl. Therm. Eng., 25(2-3), 183-190. https://doi.org/10.1016/j.applthermaleng.2004.06.013
  2. ASTM C1740 (2016), Standard Practice for Evaluating the Condition of Concrete Plates Using the Impulse-response Method, ASTM International, West Conshohocken, PA, USA.
  3. Avdelidis, N.P., Gan, T.H., Ibarra-Castanedo, C. and Maldague, X.P.V. (2011), "Infrared thermography as a nondestructive tool for materials characterisation and assessment", Proceedings of SPIE, Orlando, FL, USA, May.
  4. Bogue, R. (2013), "Sensors for condition monitoring: A review of technologies and applications", Sens. Rev., 33(4), 295-299. https://doi.org/10.1108/SR-05-2013-675
  5. Brooks, H. (2010), Basics of Retaining Wall Design: A Design Guide for Earth Retaining Structure, BHA Publication, Inc., Corona del Mar, CA, USA.
  6. Callister, W.D. and Rethwisch, D.G. (2007), Materials Science and Engineering: An Introduction, John Wiley & Sons, Inc., Hoboken, NJ, USA.
  7. Ching, F.D.K. and Winkel, S.R. (2018), Building Codes Illustrated: A Guide to Understanding the 2018 International Building Code, John Wiley & Sons, Inc., Hoboken, NJ, USA.
  8. Cho, N.J., Cha, W. and Kim, H.K. (2016), "Non-destructive detection of underground cavities using thermal images", Electron. J. Geotech. Eng., 21(16), 5465-5476.
  9. Choudhury, D. and Chatterjee, S. (2006), "Dynamic active earth pressure on retaining structures", Sadhana, 31(6), 721-730. https://doi.org/10.1007/BF02716891
  10. Davis, A.G. (2003), "The nondestructive impulse response test in North America: 1985-2001", NDT & E Int., 36(4), 185-193. https://doi.org/10.1016/S0963-8695(02)00065-8
  11. Davis, A.G. and Dunn, C.S. (1974), "From theory to field experience with the non-destructive vibration testing of piles", Proceedings of the Institution of Civil Engineers, 57(4), 571-593. https://doi.org/10.1680/iicep.1974.3895
  12. Embacher, R., Schultz, A. and Snyder, M. (2001), "Condition and durability of segmental concrete block retaining walls along roadways in Minnesota", Research Report No. MN/RC-2001-16; Minnesota Department of Transportation.
  13. Finno, R.J. and Chao, H. (2005), "Guided waves in embedded concrete pile", J. Geotech. Geoenviron., 131(1), 11-19. https://doi.org/10.1061/(ASCE)1090-0241(2005)131:1(11)
  14. Frodella, W., Morelli, S., Gigli, G. and Casagli, N. (2014), "Contribution of infrared thermography to the slope instability characterization", Proceedings of World Landslide Forum, Beijing, China, June.
  15. Gazetas, G. (1983), "Analysis of machine foundation vibration: State of the art", Soil Dyn. Earthq. Eng., 2(1), 1-42. https://doi.org/10.1016/0261-7277(83)90025-6
  16. Grandt, A.F. (2004), Fundamentals of Structural Integrity: Damage Tolerant Design and Nondestructive Evaluation, John Wiley & Sons, Inc., Hoboken, NJ, USA.
  17. Guerin, A., Jaboyedoff, M., Collins, B.D., Derron, M.H., Stock, G.M., Matasci, B., Lefeuvre, C. and Podladchikov, Y.Y. (2019), "Detection of rock bridges by infrared thermal imaging and modeling". Sci. Rep., 9(1), 1-19. https://doi.org/10.1038/s41598-019-49336-1
  18. Guo, X. and Vavilov, V. (2013), "Crack detection in aluminum parts by using ultrasound-excited infrared thermography", Infrared Phys. Technol., 61, 149-156. https://doi.org/10.1016/j.infrared.2013.08.003
  19. Hugenschmidt, J. and Kalogeropoulos, A. (2009), "The inspection of retaining walls using GPR", J. Appl. Geophy., 67(4), 335-344. https://doi.org/10.1016/j.jappgeo.2008.09.001
  20. Hui, T.H.H. and Sun, H.W. (2005), "Trial application of thermal infra-red image and seismic sympathetic vibration techniques for slope investigation", GEO Technical Note No. TN1/200; Civil Engineering and Development Department, The Government of the Hong Kong Special Administrative Region.
  21. Ibarra-Castanedo, C., Tarpani, J.R. and Maldague, X.P. (2013), "Nondestructive testing with thermography", Eur. J. Phys., 34(6), S91. https://doi.org/10.1088/0143-0807/34/6/S91
  22. KDS 14 20 72 (2021), Korean Design Standard - Design Standard for Concrete Wall, Korea Construction Standards Center, Gyeonggi-do, Republic of Korea.
  23. Kee, S.H., Oh, T., Popovics, J.S., Arndt, R.W. and Zhu, J. (2012), "Nondestructive bridge deck testing with air-coupled impact-echo and infrared thermography", J. Bridge Eng., 17(6), 928-939. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000350
  24. Koerner, R.M. and Soong, T.Y. (2001), "Geosynthetic reinforced segmental retaining walls", Geotext. Geomembr., 19(6), 359-386. https://doi.org/10.1016/S0266-1144(01)00012-7
  25. Lin, C.S., Chen, S.H., Chang, C.M. and Shen, T.W. (2019), "Crack detection on a retaining wall with an innovative, ensemble learning method in a dynamic imaging system", Sensors, 14, 12305-12348. https://doi.org/10.3390/s19214784
  26. Lo, T.Y. and Choi, K.T.W. (2004), "Building defects diagnosis by infrared thermography", Struct. Surv., 22(5), 259-263. https://doi.org/10.1108/02630800410571571
  27. McCavitt, N., Yates, M.R. and Forde, M.C. (1992), "Dynamic stiffness analysis of concrete pavement slabs", J. Transp. Eng., 118(4), 540-556. https://doi.org/10.1061/(ASCE)0733-947X(1992)118:4(540)
  28. Nazarian, S. and Reddy, S. (1996), "Study of parameters affecting impulse response method", J. Transp. Eng., 122(4), 308-315. https://doi.org/10.1061/(ASCE)0733-947X(1996)122:4(308)
  29. Nazarian, S., Reddy, S. and Baker, M. (1994), "Determination of voids under rigid pavements using impulse response method", In: Nondestructive Testing of Pavements and Backcalculation of Moduli: Second Volume, ed. Bush, A., Von, H.Q. and Baladi, G., ASTM International, West Conshohocken, PA, USA, pp. 473-487. https://doi.org/10.1520/STP18165S
  30. Obe, R.K.D., Brito, J., Mangabhai, R. and Lye, C.Q. (2017), Sustainable Construction Materials: Copper Slag, Woodhead Publishing, Cambridge, MA, USA.
  31. Ottosen, N.S., Ristinmaa, M. and Davis, A.G. (2004), "Theoretical interpretation of impulse response tests of embedded concrete structures", J. Eng. Mech., 130(9), 1062-1071. https://doi.org/10.1061/(ASCE)0733-9399(2004)130:9(1062)
  32. Padhye, R.D. and Ullagaddi, P.B. (2008), "Case study of failure of a R.C.C. counterfort retaining wall", Proceedings of the 6th International Conference on Case Histories in Geotechnical Engineering, Arlington, VA, USA, August.
  33. Papazafeiropoulos, G., Psarropoulos, P.N. and Tsompanakis, Y. (2009), "Retaining wall-soil-structure interaction effects due to seismic excitation", Proceedings of the 17th International Coference on Soil Mechanics & Geotechnical Engineering, Alexandria, Egypt, October.
  34. Park, J.Y., Jang, E., Kim, H.J. and Ihm, M.H. (2017), "Classification of ground subsidence factors for prediction of ground subsidence risk (GSR)", J. Eng. Geol., 27(2), 153-164. https://doi.org/10.9720/kseg.2017.2.153 [In Korean]
  35. Prasad, S.K., Jagadeesh, N.M. and Yadunandan, C.N. (2014), "Case studies on failure of retaining walls", i-Manager's J. Civil Eng., 3(2), 29-34. https://doi.org/10.26634/jste.3.2.3019.
  36. Rainieri, C., Fabbrocino, G. and Magistris, F.S. (2013), "An integrated seismic monitoring system for a full-scale embedded retaining wall", Geotech. Test. J., 36(1), 1-14. https://doi.org/10.1520/GTJ20120067
  37. Rizzo, P., Bartoli, I., di Scalea., F.L., Coccia, S. and Fateh, M. (2005), "High-speed defect detection in rails by non-contact guided ultrasonic testing", Proceedings of SPIE - The International Society for Optical Engineering, San Diego, CA, USA, December.
  38. Santamarina, J.C., Klein, K.A. and Fam, M.A. (2001), Soils and Waves, John Wiley & Sons, Inc., Hoboken, NJ, USA.
  39. Seo, H.J., Zhao, Y. and Wang, J. (2019), "Monitoring of retaining structures on an open excavation site with 3D laser scanning", International Conference on Smart Infrastructure and Construction 2019 (ICSIC) Driving Data-informed Decision-making, Churchill College, Cambridge, UK, July.
  40. Shinoda, M., Nakajima, S., Abe, K., Ehara, T. and Kubota, Y. (2013), "Stability inspection method for existing retaining walls", Q. Rep. RTRI, 54(3), 159-165. https://doi.org/10.2219/rtriqr.54.159
  41. Staron, D.L. (1988), "Concrete deterioration inspection system for extending the operating life of nuclear power plants", Ph.D. Dissertation, Virginia Polytechnic Institute and State University, Blacksburg, VA, USA.
  42. Tajari, M. (2010), "Use of microphone directivity for the localization of sound sources", Ph.D. Dissertation; University of Pittsburgh, Pittsburgh, PA, USA.
  43. Unnporsson, R. (2013), "Hit detection and determination in ae bursts", In: Acoustic Emission: Research and Aapplications, (ed. Sikorski, W.), IntechOpen, London, UK, pp. 1-19.
  44. Usamentiaga, R., Venegas, P., Guerediaga, J., Vega, L., Molleda, J. and Bulnes, F.G. (2014), "Infrared thermography for temperature measurement and non-destructive testing", Sensors, 14, 12305-12348. https://doi.org/10.3390/s140712305
  45. Veletsos, A.S. and Younan, A.H. (1994), "Dynamic modeling and response of soil-wall systems", J. Geotech. Geoenviron., 120(12), 2155-2179. https://doi.org/10.1061/(ASCE)0733-9410(1994)120:12(2155)
  46. Washer, G., Fenwick, R., Bolleni, N. and Harper, J. (2009), "Effects of environmental variables on infrared imaging of subsurface features of concrete bridges", Transp. Res. Rec., 2108(1), 107-114. https://doi.org/10.3141/2108-12
  47. Wu, J.H., Lin, H.M., Lee, D.H. and Fang, S.C. (2005), "Integrity assessment of rock mass behind the shotcreted slope using thermography", Eng. Geol., 80(1), 164-173. https://doi.org/10.1016/j.enggeo.2005.04.005
  48. Yang, H., Koopialipoor, M., Armaghani, D.J., Gordan, B., Khorami, M. and Tahir, M.M. (2019), "Intelligent design of retaining wall structures under dynamic conditions", Steel Compos. Struct., Int. J., 31(6), 629-640. http://dx.doi.org/10.12989/scs.2019.31.6.629
  49. Yoo, S. (2017), "Engineering application of infrared image for stability evaluation on concrete retaining wall", Master's Thesis; Kookmin University, Seoul, Korea.
  50. Yoo, C. and Jung, H.Y. (2006), "Case history of geosynthetic reinforced segmental retaining wall failure", J. Geotech. Geoenviron., 132(12), 1538-1548. https://doi.org/10.1061/(ASCE)1090-0241(2006)132:12(1538)
  51. Zabin, A., Khalil, B., Ali, T., Abdalla, J.A. and Elaksher, A. (2020), "A semi-automated method for integrating textural and material data into as-built BIM using TIS", Adv. Comput. Des., Int. J., 5(2), 127-146. http://dx.doi.org/10.12989/acd.2020.5.2.127