Smart Structures and Systems

  • 제28권4호
  • /
  • Pages.553-566
  • /
  • 2021
  • /
  • 1738-1584(pISSN)
  • /
  • 1738-1991(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Hybrid fragility curve derivation of buildings based on post-earthquake reconnaissance data

  • Lee, Sangmok (Department of Urban and Environmental Engineering, Ulsan National Institute of Science and Technology (UNIST)) ;
  • Moon, Do-Soo (Department of Civil Engineering, University of Hawaii at Manoa) ;
  • Kim, Byungmin (Department of Urban and Environmental Engineering, Ulsan National Institute of Science and Technology (UNIST)) ;
  • Kim, Jeongseob (Department of Urban and Environmental Engineering, Ulsan National Institute of Science and Technology (UNIST)) ;
  • Lee, Young-Joo (Department of Urban and Environmental Engineering, Ulsan National Institute of Science and Technology (UNIST))
  • 투고 : 2021.01.08
  • 심사 : 2021.05.28
  • 발행 : 2021.10.25
⟨ 이전 논문 다음 논문 ⟩

초록

This study proposes a new hybrid method that uses both of post-earthquake reconnaissance data and numerical analysis results based on a finite element (FE) model. As the uncertainty of a capacity threshold for a structural damage state needs to be estimated carefully, in the proposed method, the probabilistic distribution parameters of capacity thresholds are evaluated based on post-earthquake reconnaissance data. Subsequently, the hybrid fragility curves were derived for several damage states using the updated distribution parameters of capacity thresholds. To illustrate the detailed process of the proposed hybrid method, it was applied to piloti-type reinforce concrete (RC) buildings which were affected by the 2017 Pohang earthquake, Korea. In the example, analytical fragility curves were derived first, and then hybrid fragility curves were obtained using the distribution parameters of capacity thresholds which were updated based on actual post-earthquake reconnaissance data about the Pohang city. The results showed that the seismic fragility estimates approached to the empirical failure probability at 0.27 g PGA, corresponding to the ground motion intensity of the Pohang earthquake. To verify the proposed method, hybrid fragility curves were derived with the hypothetical reconnaissance data sets created based on assumed distribution parameters with errors of 10% and 1%. As a result, it was identified that the distribution parameters accurately converged to the assumed parameters and the case of 1% error had better convergence than that of 10% error.

키워드

과제정보

This research was supported by a grant (2020-MOIS31-013) of Fundamental Technology Development Program for Extreme Disaster Response funded by Ministry of Interior and Safety (MOIS, Korea).

참고문헌

  1. Ang, A.H.-S. and Tang, W.H. (2007), Probability Concepts in Engineering: Emphasis on Applications to Civil and Environmental Engineering, (2nd Edition), John Wiley & Sons, Hoboken, NJ, USA.
  2. Askan, A. and Yucemen, M.S. (2010), "Probabilistic methods for the estimation of potential seismic damage: Application to reinforced concrete buildings in Turkey", Struct. Saf., 32(4), 262-271. https://doi.org/10.1016/j.strusafe.2010.04.001
  3. Barbato, M., Gu, Q. and Conte, J.P. (2010), "Probabilistic pushover analysis of structural and soil-structure systems", J. Struct. Eng., 136(11), 1330-1341. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000231
  4. Der Kiureghian, A. (2005), First- and Second-Order Reliability Methods, Engineering Design Reliability Handbook, (edited by Nikolaidis, E., Ghiocel, D.M. and Singhal, S.), Chapter 14, CRC Press, Boca Raton, FL, USA.
  5. Dolsek, M. (2012), "Simplified method for seismic risk assessment of buildings with consideration of aleatory and epistemic uncertainty", Struct. Infrastruct. Eng., 8(10), 939-953. https://doi.org/10.1080/15732479.2011.574813
  6. Ellingwood, B.R., Celik, O.C. and Kinali, K. (2007), "Fragility assessment of building structural systems in Mid-America", Earthq. Eng. Struct. Dyn., 36(13), 1935-1952. https://doi.org/10.1002/eqe.693
  7. Elnashai, A.S., Papanikolaou, V.K. and Lee, D. (2010), "ZEUS NL - A System for Inelastic Analysis of Structures", User's manual; Mid-America Earthquake (MAE) Center, Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, Urbana, IL, USA.
  8. Federal Emergency Management Agency (FEMA) (2013), "Hazus-MH 2.1: Technical manual. Multi-hazard loss estimation methodology, earthquake model".
  9. Giordano, N., De Luca, F., Sextos, A., Cortes, F.R., Ferreira, C.F. and Wu, J. (2021), "Empirical seismic fragility models for Nepalese school buildings", Nat. Hazards, 105, 339-362. https://doi.org/10.1007/s11069-020-04312-1
  10. Guneyisi, E.M. and Altay, G. (2008), "Seismic fragility assessment of effectiveness of viscous dampers in R/C buildings under scenario earthquakes", Struct. Saf., 30(5), 461-480. https://doi.org/10.1016/j.strusafe.2007.06.001
  11. Haukaas, T. (2003), "Finite element reliability and sensitivity methods for performance-based engineering", Ph.D. Dissertation; University of California, Berkeley, CA, USA.
  12. Hueste, M.B.D. and Bai, J.W. (2007), "Seismic retrofit of a reinforced concrete flat-slab structure: Part II-Seismic fragility analysis", Eng. Struct., 29(6), 1178-1188. https://doi.org/10.1016/j.engstruct.2006.07.022
  13. Jaiswal, K.S., Aspinall, W., Perkins, D., Wald, D. and Porter, K.A. (2012), "Use of expert judgment elicitation to estimate seismic vulnerability of selected building types", Proceedings of the 15th World Conference on Earthquake Engineering, Lisbon, Portugal, September.
  14. Ji, J., Elnashai, A.S. and Kuchma, D.A. (2009), "Seismic fragility relationships of reinforced concrete high-rise buildings", Struct. Des. Tall Spec., 18(3), 259-277. https://doi.org/10.1002/tal.408
  15. Kang, S., Kim, B., Bae, S., Lee, H. and Kim, M. (2019), "Earthquake-induced ground deformations in the low-seismicity region: a case of the 2017 M5.4 Pohang, South Korea, earthquake", Earthq. Spectra, 35, 1235-1260. https://doi.org/10.1193/062318EQS160M
  16. Kappos, A.J., Stylianidis, K.C. and Pitilakis, K. (1998), "Development of seismic risk scenarios based on a hybrid method of vulnerability assessment", Nat. Hazards, 17(2), 177- 192, https://doi.org/10.1023/A:1008083021022
  17. Kappos, A.J., Panagopoulos, G., Panagiotopoulos, C. and Penelis, G. (2006), "A hybrid method for the vulnerability assessment of R/C and URM buildings", B. Earthq. Eng., 4(4), 391-413. https://doi.org/10.1007/s10518-006-9023-0
  18. Kim, H., Sim, S.-H., Lee, J., Lee, Y.-J. and Kim, J.-M. (2017), "Flood fragility analysis for bridges with multiple failure modes", Adv. Mech. Eng., 9(3), 1-11. https://doi.org/10.1177/1687814017696415
  19. Kim, T., Chu, Y., Kim, S.R. and Bhandari, D. (2018), "Seismic behavior of domestic piloti-type buildings damaged by 2017 Pohang earthquake", J. Earthq. Eng. Soc. Korea, 22(3), 161- 168, (in Korean), https://doi.org/10.5000/EESK.2018.22.3.161
  20. Kim, B., Ji, Y., Kim, M., Lee, Y.-J., Kang, H., Yun, N.-R., Kim, H. and Lee, J. (2020a), "Building damage caused by the 2017 M5.4 Pohang, South Korea, earthquake, and effects of ground conditions", J. Earthq. Eng., 1-19. https://doi.org/10.1080/13632469.2020.1785585
  21. Kim, H.-S., Kim, M., Baise, L.G. and Kim, B. (2020b), "Local and regional evaluation of liquefaction potential index and liquefaction severity number for liquefaction-induced sand boils in Pohang, South Korea", Soil Dyn. Earthq. Eng., 106459. https://doi.org/10.1016/j.soildyn.2020.106459
  22. Kircher, C.A., Whitman, R.V. and Holmes, W.T. (2006), "HAZUS earthquake loss estimation methods", Nat. Hazards Rev., 7(2), 45-59. https://doi.org/10.1061/(ASCE)1527-6988(2006)7:2(45)
  23. Kwon, O.-S. and Elnashai, A. (2006), "The effect of material and ground motion uncertainty on the seismic vulnerability curves of RC structure", Eng. Struct., 28(2), 289-303. https://doi.org/10.1016/j.engstruct.2005.07.010
  24. Lee, Y.-J. and Moon, D.-S. (2014), "A new methodology of the development of seismic fragility curves", Smart Struct. Syst., Int. J., 14(5), 847-867. http://dx.doi.org/10.12989/sss.2014.14.5.847
  25. Lee, Y.-J. and Song, J. (2012), "Finite-element-based system reliability analysis of fatigue-induced sequential failures", Reliab. Eng. Syst. Safe., 108, 131-141. https://doi.org/10.1016/j.ress.2012.05.007
  26. Lee, Y.-J., Song, J. and Tuegel, E. (2008), "Finite element system reliability analysis of a wing torque box", Proceedings of the 10th AIAA Nondeterministic Approaches Conference, Schaumburg, IL, USA, April.
  27. Lee, J., Lee, Y.-J., Kim, H., Sim, S.-H. and Kim, J.-M. (2016), "A new methodology development for flood fragility curve derivation considering structural deterioration for bridges", Smart Struct. Syst., Int. J., 17(1), 149-165. http://dx.doi.org/10.12989/sss.2016.17.1.149
  28. Li, L.-X., Li, H.-N. and Li, C. (2018), "Seismic fragility assessment of self-centering RC frame structures considering maximum and residual deformations", Struct. Eng. Mech., Int. J., 68(6), 677-689. https://doi.org/10.12989/sem.2018.68.6.677
  29. Liu, Z. and Zhang, Z. (2017), "Fragility analysis of concrete-filled steel tube arch bridge subjected to near-fault ground motion considering the wave passage effect", Smart Struct. Syst., Int. J., 19(4), 415-429. https://doi.org/10.12989/sss.2017.19.4.415
  30. Martinez, A., Hube, M.A. and Rollins, K.M. (2017), "Analytical fragility curves for non-skewed highway bridges in Chile", Eng. Struct., 141, 530-542. https://doi.org/10.1016/j.engstruct.2017.03.041
  31. Montiel, M.A. and Ruiz, S.E. (2007), "Influence of structural capacity uncertainty on seismic reliability of buildings under narrow-band motions", Earthq. Eng. Struct. Dyn., 36(13), 1915- 1934. https://doi.org/10.1002/eqe.711
  32. Moon, D.-S., Lee, Y.-J. and Lee, S. (2018), "Fragility analysis of space reinforced concrete frame structures with structural irregularity in plan", J. Struct. Eng., 144(8), 04018096. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002092
  33. Moradloo, J., Naserasadi, K. and Zamani, H. (2018), "Seismic fragility evaluation of arch concrete dams through nonlinear incremental analysis using smeared crack model", Struct. Eng. Mech., Int. J., 68(6), 747-760. https://doi.org/10.12989/sem.2018.68.6.747
  34. Mosleh, A. and Apostolakis, G. (1986), "The assessment of probability distributions from expert opinions with an application to seismic fragility curves", Risk Anal., 6(4), 447-461. https://doi.org/10.1111/j.1539-6924.1986.tb00957.x
  35. Paik, I.-Y., Shim, C.-S., Chung, Y.-S. and Sang, H.-J. (2011), "Statistical properties of material strength of concrete, re-bar and strand used in domestic construction site", J. Korea Concr. Inst., 23(4), 421-430. [In Korean] https://doi.org/10.4334/JKCI.2011.23.4.421
  36. Park, Y.-J. and Ang, A.H.-S. (1985), "Mechanistic seismic damage model for reinforced concrete", J. Struct. Eng., 111(4), 722-739. https://doi.org/10.1061/(ASCE)0733-9445(1985)111:4(722)
  37. Pitilakis, K., Crowley, H. and Kaynia, A.M. (2014), "SYNER-G: typology definition and fragility functions for physical elements at seismic risk", Geotec. Geol. Earthq. Eng., 27, 1-28. https://doi.org/10.1007/978-94-007-7872-6
  38. Ramamoorthy, S.K., Gardoni, P. and Bracci, J.M. (2006), "Probabilistic demand models and fragility curves for reinforced concrete frames", J. Struct. Eng., 132(10), 1563-1572. https://doi.org/10.1061/(ASCE)0733-9445(2006)132:10(1563)
  39. Razzaghi, M.S., Safarkhanlou, M., Mosleh, A. and Hosseini, P. (2018), "Fragility assessment of RC bridges using numerical analysis and artificial neural networks", Earthq. Struct., Int. J., 15(4), 431-441. http://dx.doi.org/10.12989/eas.2018.15.4.431
  40. Rossetto, T. and Elnashai, A. (2003), "Derivation of vulnerability functions for European-type RC structures based on observational data", Eng. Struct., 7(3), 1241-1263. https://doi.org/10.1016/S0141-0296(03)00060-9
  41. Rosti, A., Rota, M. and Penna, A. (2020), "Empirical fragility curves for Italian URM buildings", Bull. Earthq. Eng., 19(8), 3057-3076. https://doi.org/10.1007/s10518-020-00845-9
  42. Silva, V., Crowley, H., Varum, H., Pinho, R. and Sousa, R. (2014), "Evaluation of analytical methodologies used to derive vulnerability functions", Earthq. Eng. Struct. Dyn., 43(2), 181-204. https://doi.org/10.1002/eqe.2337
  43. Sim, C., Laughery, L., Chiou, T.C. and Weng, P.-W. (2018), 2017 Pohang Earthquake - Reinforced Concrete Building Damage Survey. https://datacenterhub.org/resources/14728
  44. Singhal, A. and Kiremidjian, A.S. (1998), "Bayesian updating of fragilities with application to RC frames", J. Struct. Eng., 124(8), 922-929. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:8(922)
  45. Steelman, J., Song, J. and Hajjar, J.F. (2007), "Integrated data flow and risk aggregation for consequence-based risk management of seismic regional loss", Mid-America Earthquake Center, University of Illinois at Urbana-Champaign, Urbana, IL, USA, November.
  46. Vamvatsikos, D. and Cornell, C.A. (2002), "Incremental dynamic analysis", Earthq. Eng. Struct. Dyn., 31(3), 491-514. https://doi.org/10.1002/eqe.141
  47. Wen, Y.K., Ellingwood, B.R. and Bracci, J.M. (2004), "Vulnerability function framework for consequence-based engineering", MAE Center Report 04-04.
  48. Yoon, S., Lee, Y.-J. and Jung, H.-J. (2018), "A comprehensive framework for seismic risk assessment of urban water transmission", Int. J. Disast. Risk Re., 31, 983-994. https://doi.org/10.1016/j.ijdrr.2018.09.002
  49. Yu, X., Lu, D. and Li, B. (2016), "Estimating uncertainty in limit state capacities for reinforced concrete frame structures through pushover analysis", Earthq. Struct., Int. J., 10(1), 141-161. https://doi.org/10.12989/eas.2016.10.1.141