DOI QR코드

DOI QR Code

Experimental study on cold-formed lipped channel stub columns reinforced by steel bars or steel strips

  • Chen, Jian-Feng (School of Civil Engineering, Chang'an University) ;
  • Chen, Ming-Qi (School of Civil Engineering, Chang'an University) ;
  • Shen, Yong-Kang (School of Urban Planning and Municipal Engineering, Xi'an Polytechnic University) ;
  • Shao, Jian-Hua (Experimental Center of School of Civil Engineering and architecture, Jiangsu University of Science and Technology) ;
  • Yang, Xin-Xin (School of Civil Engineering, Chang'an University)
  • 투고 : 2020.12.18
  • 심사 : 2021.05.31
  • 발행 : 2021.08.10

초록

In this paper, the axial compressive properties of cold-formed steel lipped channel stub columns strengthened by rebars or steel strips are experimentally studied. The experiment included two sections. A kind of columns with local buckling is reinforced longitudinally by steel strips at the web. The other is the columns with distorted buckling, which is reinforced longitudinally by steel bars at the curling edge. The failure mode, deformation characteristics, ultimate bearing capacity and load displacement curve of the specimen are obtained through the experiment. On the basis of the experiment, the calculation results of theoretical axial bearing capacity of cold-formed steel lipped channel stub columns in Chinese, North American and Australian code are compared and analyzed. Research indicates: First, the cold-formed steel lipped channel stub columns strengthened by steel bars or steel strips can effectively improve the compressive bearing capacity of the specimen. Secondly, when the initial stress ratio of specimen is less than 0.3, the reinforcement effect is ideal. Thirdly, the three standards don't stipulate the calculation of theoretical bearing capacity of the specimen strengthened after loading, so there is a large deviation between the theoretical calculation value and the test value.

키워드

과제정보

The authors are sincerely appreciated to the financial support as following: 1. The Fundamental Research Funds for the Central Universities, CHD (Program No. 300102289104) 2. The Natural Science Foundation of Shaanxi Province China (Program No. 2019JM-522).

참고문헌

  1. Anbarasu, M. and Murugapandian, G. (2016), "Experimental study on cold-formed steel web stiffened lipped channel columns undergoing distortional-global interaction", Mater. Struct., 49(4), 1433-1442. http://doi.org/10.1617/s11527-015-0586-6.
  2. AS/NZS 4600-2018. (2018), "Cold-formed steel structures", Sydney-Wellington, Standards of Australia and Standards of New Zealand.
  3. Chen, B., Roy, K., Uzzaman, A., Raftery, G. and Lim, J.B.P. (2020), "Axial strength of back-to-back cold-formed steel channels with edge-stiffened holes, un-stiffened holes, and plain webs", J. Constr. Steel Res., 174, 106313. http://doi.org/10.1016/j.jcsr.2020.106313.
  4. Chen, B., Roy, K., Uzzaman, A., Raftery, G., Nash, D., Clifton, G.C., Pouladi, P. and Lim, J.B.P. (2019), "Effects of edge-stiffened web openings on the behaviour of cold-formed steel channel sections under compression", Thin Wall. Struct., 144:106307-106307. http://doi.org/10.1016/j.tws.2019.106307.
  5. Chen, M.T., Young, B., Andre, Dias. Martins., Camotim, D. and Dinis, P.B. (2020) "Experimental investigation on cold-formed steel stiffened lipped channel columns undergoing local-distortional interaction", Thin Wall. Struct., 150, 106682. http://doi.org/10.1016/j.tws.2020.106682.
  6. Chen, S.F. (2002), "Local Interactive Bucking and Distortional Buckling of Lipped Channels", J. Build. Struct., 23(1), 27-32. http://doi.org/10.1007/BF02960786.
  7. Chen, S.F. (2004), "Guide for the Design of Steel Structure Stability", China Building Industry Press, Bei Jing, BJ, China.
  8. Cheng, Y. (2012), "Cold-formed steel flexural member with edge stiffened holes: Behavior, optimization, and design", J. Constr. Steel Res., 71, p.210-218. http://doi.org/10.1016/j.jcsr.2011.09.008.
  9. GB/T 228.1-2010. (2011), "Metallic materials-tensile testing method of test at ambient temperature", Bei Jing, BJ, China.
  10. GB50018-2002. (2002), "Technical code of cold-formed thin-wall steel structures", Bei Jing, BJ, China.
  11. Li, Y.Q., Liu, X., Shen, Z.Y., Yao, X.Y. and Qin, Y.F. (2010), "Experimental Study on Distortional Buckling Control for High-strength Cold-formed Thin-walled Steel Lipped Channel Columns Subject to Axial Compression", J. Build. Struct., 31(11), 10-16.
  12. Lu, W., Ling, Z., Geng, Q., Liu, W., Yang, H. and Yue, K. (2015), "Study on flexural behaviour of glulam beams reinforced by Near Surface Mounted (NSM) CFRP laminates", Constr. Build. Mater., 91, 23-31. http://doi.org/10.1016/j.conbuildmat.2015.04.050.
  13. Lu, W., Wang, L. and Wu, J. (2016), "Behavior of Glulam Columns Reinforced by Near-Surface-Mounted CFRP Laminates under Eccentric Compression Loading", J. Struct. Eng., 142(11), 04016109.1-04016109.13. http://doi.org/10.1061/(ASCE)ST.1943-541X.0001585.
  14. Lu, Y., Li, W., Zhou, T. and Wu, H. (2017), "Novel local buckling formulae for cold-formed Lipped channel columns considering end condition effect", Thin. Wall. Struct., 116, 265-276. http://doi.org/10.1016/j.tws.2017.02.034.
  15. Manikandan, P. and Arun, N. (2016) "Numerical Investigation on Cold-Formed Steel Lipped Channel Columns with Intermediate Web Stiffeners", J. Inst. Eng., 97(1), 1-7. http://doi.org/10.1007/s40030-016-0148-0.
  16. Martins, A.D., Dinis, P.B. and Camotim, D. (2016), "On the influence of local-distortional interaction in the behaviour and design of cold-formed steel web-stiffened lipped channel columns", Thin Wall. Struct., 101, 181-204. http://doi.org/10.1016/j.tws.2015.11.021.
  17. North American Specification. (2016), "North American Specification for the Design of Cold-Formed Steel Structural Members: 2016 Edition", Washington, D.C. American Iron and Steel Institute.
  18. Phan, D.K. and Rasmussen, K.J.R. (2019), "Flexural rigidity of cold-formed steel built-up members", Thin Wall. Struct., 140, 438-449. http://doi.org/10.1016/j.tws.2019.03.051.
  19. Roy, K., Chen, B., Fang, Z., Uzzaman, A., Chen, X. and Lim, J.B.P. (2021), "Local and distortional buckling behaviour of back-to-back built-up aluminium alloy channel section columns", Thin Wall. Struct., 163, 107713. http://doi.org/10.1016/j.tws.2021.107713.
  20. Schafer, BW. (2002), "Local, distortional, and Euler buckling in thin-walled columns", J. Struct. Eng. (N Y N Y), 128(3), 289-299. http://doi.org/10.1061/(ASCE)0733-9445(2002)128:3(289).
  21. Selvaraj, S. and Madhavan, M. (2019), "Structural Design of Cold-formed Steel face-to-face Connected Built-up beams using Direct Strength Method", J. Constr. Steel Res., 160, 613-628. http://doi.org/10.1016/j.jcsr.2019.05.053.
  22. Shahraki, M., Sohrabi, M.R., Azizyan, G. and Narmashiri, K. (2019), "Strengthening of deficient steel SHS columns under axial compressive loads using CFRP", Steel Compos. Struct., 30(1), 69-79. http://doi.org/10.12989/scs.2019.30.1.069.
  23. Silvestre, N. (2006), "Local-Plate and Distortional Postbuckling Behavior of Cold-Formed Steel Lipped Channel Columns with Intermediate Stiffeners", J. Struct. Eng., 132(4), 529-540. http://doi.org/10.1061/(ASCE)0733-9445(2006)132:4(529).
  24. Szymczak, C. and Kujawa, M. (2016), "On local buckling of cold-formed channel members", Thin Wall. Struct., 106, 93-101. http://doi.org/10.1016/j.tws.2016.04.017.
  25. Yao, X.Y. and Li, Y.Q. (2014), "Distortional Buckling Controlling of Cold-formed Thin-walled Steel Members with Lipped Channel Section", J. Build. Struct., 35(6), 93-101. 10.6052/j.issn.1000-4750.2013.04.0308.
  26. Zhou, X.H., Mo, T., Zhou, Q.S. and Liu, Y. (2002), "Study on the Plate-assembly Effects on Edge-stiffened Plate Elements in Design Approach of Effective Width-to-thickness Ratio", J. Build. Struct., 2002(3), 38-44. http://doi.org/10.1007/BF02960786.