Advances in nano research

  • 제11권1호
  • /
  • Pages.101-113
  • /
  • 2021
  • /
  • 2287-237X(pISSN)
  • /
  • 2287-2388(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Assessment of microstructure and surface effects on vibrational characteristics of public transportation

  • Alsultan, Abdulmajeed S. (Prince Sattam Bin Abdulaziz University, College of Engineering, Department of Civil Engineering)
  • 투고 : 2020.01.04
  • 심사 : 2021.06.29
  • 발행 : 2021.07.25
⟨ 이전 논문 다음 논문 ⟩

초록

This study analyzes the influence of surface effects on transportation vibrational properties. The evaluation of vibration impacts was done in accordance with the standards laid out in ISO 2631-1 for convenience on public transport (bus). The QCM (Quarter Car Model) with a quarter vehicle mass and variable was evaluated on exchange force between paving and three vehicle typologies (car, bus, and truck) using Matlab. The driver's, passengers in the center section, and passengers in the rear overhang's comfort is evaluated. The ten-degree oscillatory bus model has been designed for analytical requirements. First, the vibration propagation effects of different bus types are examined. Numerical methods are next briefly addressed to vibration propagation modeling inside the path and in the soil. Then a detailed discussion on the development of numerical models with an examination of the appropriateness of various modeling techniques for vehicle impact analysis will be given. Bus excitation has been created by using the asphalt-concrete road roughness power-spectral density as stated in the H. Braun model. This article illustrates how this dynamic overcharge might be predetermined according to the deterioration of the pavements'surface. This is a valuable resource for the design and maintenance of road pavements.

키워드

과제정보

This project was supported by the Deanship of Scientific Research at Prince Sattam Bin Abdulaziz University under the research project No. 2020/01/17088.

참고문헌

  1. Afsar Dizaj, E., Fanaie, N. and Zarifpour, A. (2018), "Probabilistic seismic demand assessment of steel frames braced with reduced yielding segment buckling restrained braces", Adv. Struct. Eng. 21(7), 1002-1020. https://doi.org/10.1177/1369433217737115.
  2. Afshar, A., Jahandari, S., Rasekh, H., Shariati, M., Afshar, A. and Shokrgozar, A. (2020), "Corrosion resistance evaluation of rebars with various primers and coatings in concrete modified with different additives", Constr. Build. Mater., 262, 120034. https://doi.org/10.1016/j.conbuildmat.2020.120034.
  3. Al-Furjan, M., Habibi, M., Shan, L. and Tounsi, A. (2021), "On the vibrations of the imperfect sandwich higher-order disk with a lactic core using generalize differential quadrature method", Compos. Struct., 257, 113150. https://doi.org/10.1016/j.compstruct.2020.113150.
  4. Alperovitch Najenson, D., Santo, Y., Masharawi, Y., Katz-Leurer, M., Ushvaev, D. and Kalichman, L. (2010), "Low back pain among professional bus drivers: ergonomic and occupational-psychosocial risk factors", Israel Med. Assoc. J., 12(1), 26. https://doi.org/10.1155/2019/6793090. eCollection 2019.
  5. Arabnejad Khanouki, M.M., Ramli Sulong, N.H. and Shariati, M. (2010), "Investigation of seismic behaviour of Compos. Struct., with concrete filled square steel tubular (CFSST) column by push-over and time-history analyses", Proceedings of the 4th International Conference on Steel & Composite Structure, Sydney, Australia, July.
  6. Arabnejad Khanouki, M.M., Ramli Sulong, N.H., Shariati, M. and Tahir, M.M. (2016), "Investigation of through beam connection to concrete filled circular steel tube (CFCST) column", J. Const. Steel Res., 121, 144-162. https://doi.org/10.1016/j.jcsr.2016.01.002.
  7. Asadolahi, S.M. and Fanaie, N. (2020), "Performance of self-centering steel moment frame considering stress relaxation in prestressed cables", Adv. Struct. Eng., 23(9), 1813-1822. https://doi.org/10.1177/1369433219900940.
  8. Borowiec, M., Sen, A.K., Litak, G., Hunicz, J., Koszalka, G. and Niewczas, A. (2010), "Vibrations of a vehicle excited by real road profiles", Forschung im Ingenieurwesen, 74(2), 99-109. https://doi.org/10.1007/s10010-010-0119-y.
  9. Chen, C., Wang, X., Wang, Y., Yang, D., Yao, F., Zhang, W., Wang, B., Sewvandi, G. A., Yang, D. and Hu, D. (2020), "Additive manufacturing of piezoelectric materials", Adv. Funct. Mater., 30(52), 2005141, https://doi.org/10.1002/adfm.202005141.
  10. Daie, M., Jalali, A., Suhatril, M., Shariati, M., Arabnejad Khanouki, M.M., Shariati, A. and Kazemi-Arbat, P. (2011), "A new finite element investigation on pre-bent steel strips as damper for vibration control", Int. J. Phys. Sci., 6(36), 8044-8050. https://doi.org/10.5897/ijps11.1585.
  11. Davoodnabi, S.M., Mirhosseini, S.M. and Shariati, M. (2019), "Behavior of steel-concrete composite beam using angle shear connectors at fire condition", Steel Compos. Struct., 30(2), 141-147. https://doi.org/10.12989/scs.2019.30.2.141.
  12. Dong, H., Zhao, B. and Deng, Y. (2018), "Instability phenomenon associated with two typical high speed railway vehicles", Int. J. Nonlinear Mech., 105, 130-145. https://doi.org/10.1016/J.IJNONLINMEC.2018.06.006.
  13. Ebrahimi, F. and Daman, M. (2017), "Analytical investigation of the surface effects on nonlocal vibration behavior of nanosize curved beams", Adv. Nano Res., 5(1), 35-47. https://doi.org/10.12989/anr.2017.5.1.035.
  14. Ebrahimi, F., Habibi, M. and Safarpour, H. (2019), "On modeling of wave propagation in a thermally affected GNP-reinforced imperfect nanocomposite shell", Eng. Comput., 35(4), 1375-1389. https://doi.org/10.1007/s00366-018-0669-4.
  15. Ebrahimi, F., Hashemabadi, D., Habibi, M. and Safarpour, H. (2020), "Thermal buckling and forced vibration characteristics of a porous GNP reinforced nanocomposite cylindrical shell", Microsyst. Technol., 26(2), 461-473. https://doi.org/10.1007/s00542-019-04542-9.
  16. Fanaie, N., Aghajani, S. and Shamloo, S. (2012), "Theoretical assessment of wire rope bracing system with soft central cylinder", Proceedings of the 15th world conference on earthquake engineering, Lisbon, Portugal, September.
  17. Fanaie, N. and Shamlou, S.O. (2015), "Response modification factor of mixed structures", Steel Compos. Struct., 19(6), 1449-1466. https://doi.org/10.12989/scs.2015.19.6.1449.
  18. Fanaie, N., Kazerani, S. and Soroushnia, S. (2017a), "Numerical study of slotted web drilled flange moment frame connection", Int. J. Numer. Method Civil Eng., 1(3), 16-23. https://doi.org/10.1016/j.jcsr.2011.06.003.
  19. Fanaie, N. and Tahriri, M. (2017b), "Stability and stiffness analysis of a steel frame with an oblique beam using method of least work", J. Const. Steel Res., 137, 342-357 DOI: https://doi.org/10.1016/j.jcsr.2017.06.032.
  20. Fanaie, N., Faegh, S. S. and Partovi, F. (2019), "An improved and innovative formulation for calculating amplified elastic story drift induced by RBS connections in steel moment frames", J. Const. Steel Res., 160, 510-527. https://doi.org/10.1016/j.jcsr.2019.06.003.
  21. Ghabussi, A., Ashrafi, N., Shavalipour, A., Hosseinpour, A., Habibi, M., Moayedi, H., Babaei, B. and Safarpour, H. (2019), "Free vibration analysis of an electro-elastic GPLRC cylindrical shell surrounded by viscoelastic foundation using modified length-couple stress parameter", Mech. Based Des. Struct., 1-25. https://doi.org/10.1080/15397734.2019.1705166.
  22. Ghanbari Ghazijahani, T., Nabati, A., Azandariani, M.G. and Fanaie, N. (2020), "Crushing of steel tubes with different infills under partial axial loading", Thin Wall. Struct., 149, 106614. https://doi.org/10.1016/j.tws.2020.106614.
  23. Goudarzi, A., Ghassemieh, M., Fanaie, N., Laefer, D. F. and Baei, M. (2016), "Axial load effects on flush end-plate moment connections", Proceedings of the Institution of Civil Engineers Structures and Buildings, 170(3), 199-210. https://doi.org/10.1016/S0141-0296(97)00050-3.
  24. Habibi, M., Hashemabadi, D. and Safarpour, H. (2019), "Vibration analysis of a high-speed rotating GPLRC nanostructure coupled with a piezoelectric actuator", Eur. Phys. J. Plus., 134(6), 1-23 https://doi.org/10.1140/epjp/i2019-12742-7.
  25. Habibi, M., Safarpour, M. and Safarpour, H. (2020), "Vibrational characteristics of a FG-GPLRC viscoelastic thick annular plate using fourth-order Runge-Kutta and GDQ methods", Mech. Based Des. Struct., 1-22. https://doi.org/10.1080/15397734.2020.1779086.
  26. Hajilak, Z.E., Pourghader, J., Hashemabadi, D., Bagh, F.S., Habibi, M. and Safarpour, H. (2019), "Multilayer GPLRC composite cylindrical nanoshell using modified strain gradient theory", Mech. Based Des. Struct. https://doi.org/10.1080/15397734.2019.1566743.
  27. Hamidian, M., Shariati, M., Arabnejad, M. and Sinaei, H. (2011), "Assessment of high strength and light weight aggregate concrete properties using ultrasonic pulse velocity technique", Int. J. Phys. Sci., 6(22), 5261-5266 https://doi.org/10.5897/IJPS11.1081.
  28. Heydari, A. and Shariati, M. (2018), "Buckling analysis of tapered BDFGM nano-beam under variable axial compression resting on elastic medium", Struct. Eng. Mech., 66(6), 737-748. https://doi.org/10.12989/sem.2018.66.6.737.
  29. Hong, XC., Wang, G.Y., Liu, J., Song, L. and Wu, E.T. (2021), "Modeling the impact of soundscape drivers on perceived birdsongs in urban forests", J. Clean. Prod., 292, 125315. https://doi.org/10.1016/j.jclepro.2020.125315.
  30. Hosseinpour, E., Baharom, S., Badaruzzaman, W.H.W., Shariati, M. and Jalali, A. (2018), "Direct shear behavior of concrete filled hollow steel tube shear connector for slim-floor steel beams", Steel Compos. Struct., 26(4), 485-499. https://doi.org/10.12989/scs.2018.26.4.485.
  31. Hou, Z., Lu, H., Li, Y., Yang, L. and Gao, Y. (2021), "Direct ink writing of materials for electronics-related applications: A mini review", Front. Mater., 8, 91. https://doi.org/10.3389/fmats.2021.647229.
  32. Hu, J., Zhang, H., Li, Z., Zhao, C., Xu, Z. and Pan, Q. (2020), "Object traversing by monocular UAV in outdoor environment", Asian J. Control. https://doi.org/10.1002/asjc.2415.
  33. Huang, X., Zhang, Y., Moradi, Z. and Shafiei, N. (2021a), "Computer simulation via a couple of homotopy perturbation methods and the generalized differential quadrature method for nonlinear vibration of functionally graded non-uniform micro-tube", Eng. Comput., 1-18. https://doi.org/10.1007/s00366-021-01395-7.
  34. Huang, X., Zhu, Y., Vafaei, P., Moradi, Z. and Davoudi, M. (2021b), "An iterative simulation algorithm for large oscillation of the applicable 2D-electrical system on a complex nonlinear substrate", Eng. Comput., 1-13. https://doi.org/10.1007/S00366-021-01320-Y.
  35. Ismail, M., Shariati, M., Abdul Awal, A.S.M., Chiong, C.E., Sadeghipour Chahnasir, E., Porbar, A., Heydari, A. and Khorami, M. (2018), "Strengthening of bolted shear joints in industrialized ferrocement construction", Steel Compos. Struct., 28(6), 681-690 DOI: https://doi.org/10.12989/scs.2018.28.6.681.
  36. Jalali, A., Daie, M., Nazhadan, S.V.M., Kazemi-Arbat, P. and Shariati, M. (2012), "Seismic performance of structures with pre-bent strips as a damper", Int. J. Phys. Sci., 7(26), 4061-4072. https://doi.org/10.1002/eqe.880.
  37. Ji, X., Hou, C., Gao, Y., Xue, Y., Yan, Y. and Guo, X. (2020a), "Metagenomic analysis of gut microbiota modulatory effects of jujube (Ziziphus jujuba Mill.) polysaccharides in a colorectal cancer mouse model", Food Function. 11(1), 163-173. https://doi.org/10.1039/C9FO02171J.
  38. Ji, X., Hou, C., Shi, M., Yan, Y. and Liu, Y. (2020b), "An Insight into the research concerning Panax ginseng CA Meyer polysaccharides: A review", Food Rev. Int., 1-17. https://doi.org/10.1080/87559129.2020.1771363.
  39. Jiao, J., Ghoreishi, S.M., Moradi, Z. and Oslub, K. (2021), "Coupled particle swarm optimization method with genetic algorithm for the static-dynamic performance of the magneto-electro-elastic nanosystem", Eng. Comput., 1-15. https://doi.org/10.1007/s00366-021-01391-x.
  40. Katebi, J., Shoaei-parchin, M., Shariati, M., Trung, N.T. and Khorami, M. (2019), "Developed comparative analysis of metaheuristic optimization algorithms for optimal active control of structures", Eng. Comput., 1-20. https://doi.org/10.1007/s00366-019-00780-7.
  41. Kazerani, S., Fanaie, N. and Soroushnia, S. (2014), "Seismic behavior of drilled beam section in moment connections", Num. Methods Civil Eng., 1(2), 21-28. https://doi.org/10.1016/j.jcsr.2006.06.030.
  42. Khorami, M., Alvansazyazdi, M., Shariati, M., Zandi, Y., Jalali, A. and Tahir, M. (2017), "Seismic performance evaluation of buckling restrained braced frames (BRBF) using incremental nonlinear dynamic analysis method (IDA)", Proceedings of the 9th fib International PhD Symposium in Civil Engineering: Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany, July. http://doi.org/10.12989/eas.2017.13.6.531.
  43. Khorramian, K., Maleki, S., Shariati, M., Jalali, A. and Tahir, M. (2017), "Numerical analysis of tilted angle shear connectors in steel-concrete composite systems", Steel Compos. Struct., 23(1), 67-85. https://doi.org/10.12989/scs.2017.23.1.067.
  44. Khorramian, K., Maleki, S., Shariati, M. and Ramli Sulong, N.H. (2016), "Behavior of tilted angle shear connectors", Plos One, 11(2). https://doi.org/10.1371/journal.pone.0144288.
  45. Kompier, M.A. (1996), Bus drivers: Occupational stress and stress prevention, International Labour Office Geneva.
  46. Li, D., Toghroli, A., Shariati, M., Sajedi, F., Bui, D.T., Kianmehr, P., Mohamad, E.T. and Khorami, M. (2019), "Application of polymer, silica-fume and crushed rubber in the production of Pervious concrete", Smart Struct. Syst., 23(2), 207-214. https://doi.org/10.12989/sss.2019.23.2.207.
  47. Litak, G., Borowiec, M., Hunicz, J., Koszalka, G. and Niewczas, A. (2009), "Vibrations of a delivery car excited by railway track crossing", Chaos Soliton Fract., 42(1), 270-276. https://doi.org/10.1016/j.chaos.2008.11.020.
  48. Luo, Z., Sinaei, H., Ibrahim, Z., Shariati, M., Jumaat, Z., Wakil, K., Pham, B.T., Mohamad, E.T. and Khorami, M. (2019), "Computational and experimental analysis of beam to column joints reinforced with CFRP plates", Steel Compos. Struct., 30(3), 271-280. http://doi.org/10.12989/scs.2019.30.3.271.
  49. Ma, H. J., Xu, L. X. and Yang, G.H. (2021a), "Multiple environment integral reinforcement learning-based fault-tolerant control for affine nonlinear systems", IEEE T. Cybernet., 51. https://doi.org/10.1109/TCYB.2018.2889679.
  50. Ma, L., Liu, X. and Moradi, Z. (2021b), "On the chaotic behavior of graphene-reinforced annular systems under harmonic excitation", Eng. Comput., 1-25. https://doi.org/10.1007/s00366-020-01210-9.
  51. Mansouri, I., Shariati, M., Safa, M., Ibrahim, Z., Tahir, M. and Petkovic, D. (2019), "Analysis of influential factors for predicting the shear strength of a V-shaped angle shear connector in composite beams using an adaptive neuro-fuzzy technique", J. Intell. Manuf., 30(3), 1247-1257. https://doi.org/10.1007/s10845-017-1306-6.
  52. Mehrabi, P., Shariati, M., Kabirifar, K., Jarrah, M., Rasekh, H., Trung, N.T., Shariati, A. and Jahandari, S. (2021), "Effect of pumice powder and nano-clay on the strength and permeability of fiber-reinforced pervious concrete incorporating recycled concrete aggregate", Constr. Build. Mater., 287, 122652. https://doi.org/10.1016/j.conbuildmat.2021.122652.
  53. Milovancevic, M., Marinovic, J. S., Nikolic, J., Kitic, A., Shariati, M., Trung, N.T., Wakil, K. and Khorami, M. (2019), "UML diagrams for dynamical monitoring of rail vehicles", Physica A., 121169. https://doi.org/10.1016/j.physa.2019.121169.
  54. Mladenovic, D. (1997), "An analysis of constructions parameters impact on the oscillatory behaviour of the bus", M.Sc. Dissertation, The Faculty of Transport and Traffic Engineering, Belgrade, Serbia.
  55. Moghadam, H., Fanaei, N. and Motazedian, D. (2010), "Estimation of stress drop for some large shallow earthquakes using stochastic point source and finite fault modeling", Scientia Iranica, 17(3). https://doi.org/10.1093/gji/ggw374.
  56. Mohammadhassani, M., Nezamabadi Pour, H., Suhatril, M. and Shariati, M. (2013), "Identification of a suitable ANN architecture in predicting strain in tie section of concrete deep beams", Struct. Eng. Mech., 46(6), 853-868. http://doi.org/10.12989/sem.2013.46.6.853.
  57. Mohammadhassani, M., Akib, S., Shariati, M., Suhatril, M. and Arabnejad Khanouki, M.M. (2014a), "An experimental study on the failure modes of high strength concrete beams with particular references to variation of the tensile reinforcement ratio", Eng. Fail. Anal., 41, 73-80. https://doi.org/10.1016/j.engfailanal.2013.08.014.
  58. Mohammadhassani, M., Nezamabadi-Pour, H., Suhatril, M. and Shariati, M. (2014b), "An evolutionary fuzzy modelling approach and comparison of different methods for shear strength prediction of high-strength concrete beams without stirrups", Smart Struct. Syst., 14(5), 785-809. https://doi.org/10.12989/sss.2014.14.5.785.
  59. Mohammadhassani, M., Suhatril, M., Shariati, M. and Ghanbari, F. (2014c), "Ductility and strength assessment of HSC beams with varying of tensile reinforcement ratios", Struct. Eng. Mech., 48(6), 833-848. https://doi.org/10.12989/sem.2013.48.6.833.
  60. Naghipour, M., Niak, K.M., Shariati, M. and Toghroli, A. (2020a), "Effect of progressive shear punch of a foundation on a reinforced concrete building behavior", Steel Compos. Struct., 35(2), 279-294. https://doi.org/10.12989/scs.2020.35.2.279.
  61. Naghipour, M., Yousofizinsaz, G. and Shariati, M. (2020b), "Experimental study on axial compressive behavior of welded built-up CFT stub columns made by cold-formed sections with different welding lines", Steel Compos. Struct., 34(3), 347. https://doi.org/10.12989/scs.2020.34.3.347.
  62. Najarkolaie, K.F., Mohammadi, M. and Fanaie, N. (2017), "Realistic behavior of infilled steel frames in seismic events: experimental and analytical study", Bull. Earthq. Eng. 15(12), 5365-5392. https://doi.org/10.1007/s10518-017-0173-z.
  63. Nasrollahi, S., Maleki, S., Shariati, M., Marto, A. and Khorami, M. (2018), "Investigation of pipe shear connectors using push out test", Steel Compos. Struct., 27(5), 537-543. http://doi.org/10.12989/scs.2018.27.5.537.
  64. Nelson, C.M. and Brereton, P.F. (2005), "The European vibration directive", Ind. Health, 43(3), 472-479. https://doi.org/10.2486/indhealth.43.472.
  65. Ni, Z., Cao, X., Wang, X., Zhou, S., Zhang, C., Xu, B. and Ni, Y. (2021), "Facile synthesis of copper (I) oxide nanochains and the photo-thermal conversion performance of its nanofluids", Coatings, 11(7), 749. https://doi.org/10.3390/coatings11070749.
  66. Nosrati, A., Zandi, Y., Shariati, M., Khademi, K., Darvishnezhad Aliabad, M., Marto, A., Mu'azu, M., Ghanbari, E., Mandizadeh, M.B. and Shariati, A. (2018), "Portland cement structure and its major oxides and fineness", Smart Struct. Syst., 22(4), 425-432. https://doi.org/10.12989/sss.2018.22.4.425.
  67. Okunribido, O.O., Shimbles, S. J., Magnusson, M. and Pope, M. (2007), "City bus driving and low back pain: a study of the exposures to posture demands, manual materials handling and whole-body vibration", Appl. Ergon., 38(1), 29-38. https://doi.org/10.1016/j.apergo.2006.01.006.
  68. Paknahad, M., Shariati, M., Sedghi, Y., Bazzaz, M. and Khorami, M. (2018), "Shear capacity equation for channel shear connectors in steel-concrete composite beams", Steel Compos. Struct., 28(4), 483-494. https://doi.org/10.12989/scs.2018.28.4.483.
  69. Partovi, F. and Fanaie, N. (2020), "Controlling deflection of long steel I-shaped girder bridge using two V-shaped pre-tensioning cables", J. Cent. South Univ. T., 27(2), 566-577. https://doi.org/10.1007/s11771-020-4317-y.
  70. Peceliunas, R., Lukoseviciene, O. and Prentkovskis, O. (2003), "A mathematical model of the vibrating system equivalent to the vehicle in the mode of emergency braking", Transport, 18(3), 136-142. https://doi.org/10.1080/16483840.2003.10414082.
  71. Peceliunas, R., Prentkovskis, O., Garbincius, G., Nagurnas, S. and Pukalskas, S. (2005), "Experimental research into motor vehicle oscillations in the case of changeable deceleration", Transport, 20(5), 171-175. https://doi.org/10.1080/16484142.2005.9638016.
  72. Picu, A. (2009), "Whole body vibration analysis for bus drivers", SISoM. https://doi.org/10.1016/j.ergon.2012.10.003.
  73. Pourjabari, A., Hajilak, Z.E., Mohammadi, A., Habibi, M. and Safarpour, H. (2019), "Effect of porosity on free and forced vibration characteristics of the GPL reinforcement composite nanostructures", Comput. Math. Appl., 77(10), 2608-2626. https://doi.org/10.1016/j.
  74. Qi, C. and Fourie, A. (2019), "Cemented paste backfill for mineral tailings management: Review and future perspectives", Miner. Eng., 144, 106025. https://doi.org/10.1016/j.mineng.2019.106025.
  75. Qi, C., Spagnoli, D. and Fourie, A. (2020), "DFT-D study of single water adsorption on low-index surfaces of calcium silicate phases in cement", Appl. Surf. Sci., 518, 146255. https://doi.org/10.1016/j.apsusc.2020.146255.
  76. Qiao, Y.X., Sheng, S.L., Zhang, L.M., Chen, J., Yang, L.L., Zhou, H.L., Wang, Y.X., Li, H.B. and Zheng, Z.B. (2021), "Friction and wear behaviors of a high nitrogen austenitic stainless steel Fe-19Cr-15Mn-0.66 N", J. Min. Metall., Section B, 25-25. https://doi.org/10.2298/JMMB201026025Q.
  77. Rajaei, S., Shoaei, P., Shariati, M., Ameri, F., Musaeei, H.R., Behforouz, B. and de Brito, J. (2021), "Rubberized alkali-activated slag mortar reinforced with polypropylene fibres for application in lightweight thermal insulating materials", Constr. Build. Mater., 270, 121430. https://doi.org/10.1016/j.conbuildmat.2020.121430.
  78. Razavian, L., Naghipour, M., Shariati, M. and Safa, M. (2020), "Experimental study of the behavior of composite timber columns confined with hollow rectangular steel sections under compression", Struct. Eng. Mech., 74(1), 145-156. https://doi.org/10.12989/sem.2020.74.1.145.
  79. Rezaeian, A., Jahanbakhti, E. and Fanaie, N. (2020), "Numerical study of panel zone in a moment connection without continuity plates", J. Earthq. Eng., 1-19. http://doi.org/10.1080/13632469.2019.1695021.
  80. Sadeghipour Chahnasir, E., Zandi, Y., Shariati, M., Dehghani, E., Toghroli, A., Mohamed, E.T., Shariati, A., Safa, M., Wakil, K. and Khorami, M. (2018), "Application of support vector machine with firefly algorithm for investigation of the factors affecting the shear strength of angle shear connectors", Smart Struct. Syst., 22(4), 413-424. http://doi.org/10.12989/sss.2018.22.4.413.
  81. Safa, M., Shariati, M., Ibrahim, Z., Toghroli, A., Baharom, S.B., Nor, N.M. and Petkovic, D. (2016), "Potential of adaptive neuro fuzzy inference system for evaluating the factors affecting steel-concrete composite beam's shear strength", Steel Compos. Struct., 21(3), 679-688. https://doi.org/10.12989/scs.2016.21.3.679.
  82. Safa, M., Maleka, A., Arjomand, M.A., Khorami, M. and Shariati, M. (2019), "Strain rate effects on soil-geosynthetic interaction in fine-grained soil", Geomech. Eng., 19(6), 533-542. https://doi.org/10.5539/jsd.v10n2p238.
  83. Safa, M., Sari, P.A., Shariati, M., Suhatril, M., Trung, N.T., Wakil, K. and Khorami, M. (2020), "Development of neuro-fuzzy and neuro-bee predictive models for prediction of the safety factor of eco-protection slopes", Physica A. 124046. https://doi.org/10.1016/j.physa.2019.124046.
  84. Safarpour, H., Hajilak, Z.E. and Habibi, M. (2019), "A size-dependent exact theory for thermal buckling, free and forced vibration analysis of temperature dependent FG multilayer GPLRC composite nanostructures restring on elastic foundation", Int. J. Mech. Mater. Des., 15(3), 569-583. http://doi.org/10.1007/s10999-018-9431-8.
  85. Sajedi, F. and Shariati, M. (2019), "Behavior study of NC and HSC RCCs confined by GRP casing and CFRP wrapping", Steel Compos. Struct., 30(5), 417-432. https://doi.org/10.12989/scs.2019.30.5.417.
  86. Sedghi, Y., Zandi, Y., Shariati, M., Ahmadi, E., Moghimi Azar, V., Toghroli, A., Safa, M., Tonnizam Mohamad, E., Khorami, M. and Wakil, K. (2018), "Application of ANFIS technique on performance of C and L shaped angle shear connectors", Smart Struct. Syst., 22(3), 335-340. https://doi.org/10.12989/sss.2018.22.3.335.
  87. Shah, S., Ramli Sulong, N.H., Shariati, M., Khan, R. and Jumaat, M. (2016a), "Behavior of steel pallet rack beam-to-column connections at elevated temperatures", Thin Wall. Struct., 106, 471-483. https://doi.org/10.1016/j.tws.2016.05.021.
  88. Shah, S., Sulong, N.R., Jumaat, M. and Shariati, M. (2016b), "State-of-the-art review on the design and performance of steel pallet rack connections", Eng. Fail. Anal., 66, 240-258. https://doi.org/10.1016/j.engfailanal.2016.04.017.
  89. Shah, S., Sulong, N.R., Khan, R., Jumaat, M. and Shariati, M. (2016c), "Behavior of industrial steel rack connections", Mech. Syst. Signal Pr. 70, 725-740. http://doi.org/10.1016/j.ymssp.2015.08.026.
  90. Shah, S., Sulong, N.R., Shariati, M. and Jumaat, M. (2015), "Steel rack connections: Identification of most influential factors and a comparison of stiffness design methods", Plos One, 10(10), e0139422. http://doi.org/10.1371/journal.pone.0139422.
  91. Shahabi, S., Ramli Sulong, N.H., Shariati, M. and Shah, S. (2016), "Performance of shear connectors at elevated temperatures-A review", Steel Compos. Struct., 20(1), 185-203. https://doi.org/10.12989/scs.2016.20.1.185.
  92. Shao, H.M., Shen, X.Y., Li, X.T., Cui, Y., Zhang, W., Shao, Z.C. and Zhai, Y.C. (2021), "Growth mechanism and photocatalytic evaluation of flower-like ZnO micro-structures prepared with SDBS assistance", Int. J. Miner. Metall. Mater., 28(4), 729-737. https://doi.org/10.1007/s10854-015-4051-7.
  93. Shariati, A., Mohammad-Sedighi, H., Zur, K.K., Habibi, M. and Safa, M. (2020), "On the vibrations and stability of moving viscoelastic axially functionally graded nanobeams", Materials, 13(7), 1707. https://doi.org/10.3390/ma13071707.
  94. Sinaei, H., Jumaat, M.Z. and Shariati, M. (2011), "Numerical investigation on exterior reinforced concrete Beam-Column joint strengthened by composite fiber reinforced polymer (CFRP)", Int. J. Phys. Sci., 6(28), 6572-6579. https://doi.org/10.5897/IJPS11.1225
  95. Sinaei, H., Shariati, M., Abna, A.H., Aghaei, M. and Shariati, A. (2012), "Evaluation of reinforced concrete beam behaviour using finite element analysis by ABAQUS", Sci. Res. Essay, 7(21), 2002-2009. https://doi.org/10.5897/SRE11.1393.
  96. Suhatril, M., Osman, N., Sari, P.A., Shariati, M. and Marto, A. (2019), "Significance of surface eco-protection techniques for cohesive soils slope in Selangor, Malaysia", Geotech. Geologic. Eng., 37(3), 2007-2014. https://doi.org/10.1007/s10706-018-0740-3(0123.
  97. Tahmasbi, F., Maleki, S., Shariati, M., Ramli Sulong, N.H. and Tahir, M.M. (2016), "Shear capacity of C-shaped and L-shaped angle shear connectors", Plos One, 11(8), e0156989. https://doi.org/10.1371/journal.pone.0156989.
  98. Tan, L., Sun, Y., Wei, C., Tao, Y., Tian, Y., An, Y., Zhang, Y., Xiong, S. and Feng, J. (2021), "Design of robust, lithiophilic, and flexible inorganic-polymer protective layer by separator engineering enables dendrite-free lithium metal batteries with LiNi0.8Mn0.1Co0.1O2 cathode", Small, 17(13), 2007717. https://doi.org/10.1002/smll.202007717.
  99. Toghroli, A., Mohammadhassani, M., Suhatril, M., Shariati, M. and Ibrahim, Z. (2014), "Prediction of shear capacity of channel shear connectors using the ANFIS model", Steel Compos. Struct., 17(5), 623-639. http://doi.org/10.12989/scs.2014.17.5.623.
  100. Toghroli, A., Suhatril, M., Ibrahim, Z., Safa, M., Shariati, M. and Shamshirband, S. (2016), "Potential of soft computing approach for evaluating the factors affecting the capacity of steel-concrete composite beam", J. Intell. Manuf., 1-9. https://doi.org/10.1007/s10845-016-1217-y.
  101. Toghroli, A., Shariati, M., Karim, M.R. and Ibrahim, Z. (2017), "Investigation on composite polymer and silica fume-rubber aggregate pervious concrete", Proceedings of Fifth International Conference on Advances in Civil, Structural and Mechanical Engineering, Zurich, Switzerland, September.
  102. Toghroli, A., Shariati, M., Sajedi, F., Ibrahim, Z., Koting, S., Mohamad, E.T. and Khorami, M. (2018), "A review on pavement porous concrete using recycled waste materials", Smart Struct. Syst., 22(4), 433-440. https://doi.org/10.12989/sss.2018.22.4.433.
  103. Toghroli, A., Mehrabi, P., Shariati, M., Trung, N.T., Jahandari, S. and Rasekh, H. (2020), "Evaluating the use of recycled concrete aggregate and pozzolanic additives in fiber-reinforced pervious concrete with industrial and recycled fibers", Constr. Build. Mater., 252, 118997. https://doi.org/10.1016/j.conbuildmat.2020.118997.
  104. Trung, N.T., Shahgoli, A.F., Zandi, Y., Shariati, M., Wakil, K., Safa, M. and Khorami, M. (2019a), "Moment-rotation prediction of precast beam-to-column connections using extreme learning machine", Struct Eng. Mech., 70(5), 639-647. https://doi.org/10.12989/sem.2019.70.5.639.
  105. Trung, N.T., Alemi, N., Haido, J.H., Shariati, M., Baradaran, S. and Yousif, S.T. (2019b), "Reduction of cement consumption by producing smart green concretes with natural zeolites", Smart Struct. Syst., 24(3), 415-425. https://doi.org/10.12989/sss.2019.24.3.415.
  106. Tsai, Y.H., Wang, J., Chien, W.T., Wei, C.Y., Wang, X. and Hsieh, S.H. (2019), "A BIM-based approach for predicting corrosion under insulation", Autom. Constr., 107, 102923. https://doi.org/10.1016/j.autcon.2019.102923.
  107. Wang, M., Wang, W.X., Chen, H.S. and Li, Y.L. (2018), "Understanding micro-diffusion bonding from the fabrication of B 4 C/Ni composites", Int. J. Miner. Metall. Mater., 25(3), 365-374. https://doi.org/10.1016/j.jmatprotec.2008.06.014.
  108. Wei, X., Shariati, M., Zandi, Y., Pei, S., Jin, Z., Gharachurlu, S., Abdullahi, M.M., Tahir, M.M. and Khorami, M. (2018), "Distribution of shear force in perforated shear connectors", Steel Compos. Struct., 27(3), 389-399. http://doi.org/10.12989/scs.2018.27.3.389.
  109. Whitelegg, J. and Cross, W. (1995), "Health of professional drivers a report for transport & general workers union", Research Report No. 00715974; Transport Research Laboratory, West Drayton, U.K.
  110. Xu, M.X., Chen, Z.H. and Xu, M.Q. (2014), "Micro-mechanism of metal magnetic memory signal variation during fatigue", Int. J. Miner. Metall. Mater., 21(3), 259-265. https://doi.org/10.1007/s12206-016-0618-3.
  111. Yang, Y., Chen, H., Zou, X., Shi, X.L., Liu, W.D., Feng, L., Suo, G., Hou, X., Ye, X. and Zhang, L. (2020a), "Flexible carbon-fiber/semimetal Bi nanosheet arrays as separable and recyclable plasmonic photocatalysts and photoelectrocatalysts", ACS Appl. Mater. Interfac., 12(22), 24845-24854. https://doi.org/10.1016/j.matchemphys.2021.124990.
  112. Yang, Z., Xu, P., Wei, W., Gao, G., Zhou, N. and Wu, G. (2020b), "Influence of the crosswind on the pantograph arcing dynamics", IEEE T. Plasma Sci., 48(8), 2822-2830. https://doi.org/10.1109/TPS.2020.3010553.
  113. Yazdani, M., Kabirifar, K., Frimpong, B.E., Shariati, M., Mirmozaffari, M. and Boskabadi, A. (2020), "Improving construction and demolition waste collection service in an urban area using a simheuristic approach: A case study in Sydney, Australia", J. Clean. Prod. 280, 124138. https://doi.org/10.1016/j.jclepro.2020.124138.
  114. Yin, P.F., Han, X.Y., Zhou, C., Xia, C.H., Hu, C.L. and Sun, L.L. (2015), "Large-scale synthesis of nickel sulfide micro/nanorods via a hydrothermal process", Int. J. Miner. Metall. Mater., 22(7), 762-769. https://doi.org/10.1007/978-3-319-63215-5_20.
  115. Zandi, Y., Shariati, M., Marto, A., Wei, X., Karaca, Z., Dao, D., Toghroli, A., Hashemi, M.H., Sedghi, Y. and Wakil, K. (2018), "Computational investigation of the comparative analysis of cylindrical barns subjected to earthquake", Steel Compos. Struct., 28(4), 439-447. https://doi.org/10.12989/scs.2018.28.4.439.
  116. Zhang, B., Ji, D., Fang, D., Liang, S., Fan, Y. and Chen, X. (2019), "A novel 220-GHz GaN diode on-chip tripler with high driven power", IEEE Electr. Device L., 40(5), 780-783. https://doi.org/10.1109/LED.2019.2903430.
  117. Zhang, B., Niu, Z., Wang, J., Ji, D., Zhou, T., Liu, Y., Feng, Y., Hu, Y., Zhang, J. and Fan, Y. (2020a), "Four-hundred gigahertz broadband multi-branch waveguide coupler", IET Microw. Antennas Propag., 14(11), 1175-1179. https://doi.org/10.1049/iet-map.2020.0090.
  118. Zhang, L., Zheng, J., Tian, S., Zhang, H., Guan, X., Zhu, S., Zhang, X., Bai, Y., Xu, P. and Zhang, J. (2020b), "Effects of Al3+ on the microstructure and bioflocculation of anoxic sludge", J. Environ. Sci., 91, 212-221. https://doi.org/10.1016/j.jes.2020.02.010.
  119. Zhang, L., Zhang, M., You, S., Ma, D., Zhao, J. and Chen, Z. (2021), "Effect of Fe3+ on the sludge properties and microbial community structure in a lab-scale A2O process", Sci. Total Environ., 780, 146505. https://doi.org/10.1016/j.scitotenv.2021.146505.
  120. Zhang, X. and Zhang, Y. (2021), "Experimental study on enhanced heat transfer and flow performance of magnetic nanofluids under alternating magnetic field", Int. J. Therm. Sc., 164, 06897. https://doi.org/10.1016/j.ijthermalsci.2021.106897.
  121. Zhao, Y., Moradi, Z., Davoudi, M. and Zhuang, J. (2021), "Bending and stress responses of the hybrid axisymmetric system via state-space method and 3D-elasticity theory", Eng. Comput., 1-23. https://doi.org/10.1007/s00366-020-01242-1.
  122. Zhu, Q. and Ishitobi, M. (2004), "Chaos and bifurcations in a nonlinear vehicle model", J. Sound Vib., 275(3-5), 1136-1146. https://doi.org/10.1016/j.ijsolstr.2005.06.070.
  123. Zhu, Q. and Ishitobi, M. (2006), "Chaotic vibration of a nonlinear full-vehicle model", Int. J. Solids Struct., 43(3-4), 747-759. https://doi.org/10.1016/j.ijsolstr.2005.06.070.
  124. Zhu, H., An, Y., Shi, M., Li, Z., Chen, N., Yang, C. and Xiao, P. (2021), "Porous N-doped carbon/MnO2 nanoneedles for high performance ionic liquid-based supercapacitors", Mater. Lett., 296, 129837. https://doi.org/10.1016/j.matlet.2021.129837.
  125. Ziaei-Nia, A., Shariati, M. and Salehabadi, E. (2018), "Dynamic mix design optimization of high-performance concrete", Steel Compos. Struct., 29(1), 67-75. http://doi.org/10.12989/scs.2018.29.1.067.