Advances in concrete construction

  • 제11권5호
  • /
  • Pages.419-428
  • /
  • 2021
  • /
  • 2287-5301(pISSN)
  • /
  • 2287-531X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Influence of fly ash and GGBFS on the pH value of cement mortar in different curing conditions

  • Shafigh, Payam (Centre for Building, Construction & Tropical Architecture (BuCTA), Faculty of Built Environment, University of Malaya) ;
  • Yousuf, Sumra (Department of Civil Engineering, Faculty of Engineering, Universiti of Malaya) ;
  • Ibrahim, Zainah (Department of Civil Engineering, Faculty of Engineering, Universiti of Malaya) ;
  • Alsubari, Belal (Department of Civil Engineering, Faculty of Engineering, Miami College of Henan University) ;
  • Asadi, Iman (Centre for Building, Construction & Tropical Architecture (BuCTA), Faculty of Built Environment, University of Malaya)
  • 투고 : 2020.06.02
  • 심사 : 2021.04.29
  • 발행 : 2021.05.25
⟨ 이전 논문 다음 논문 ⟩

초록

The pH of cement-based materials (CBMs) is an important factor for their durability, sustainability, and long service life. Currently, the use of supplementary cementitious materials (SCMs) is becoming mandatory due to economic, environmental, and sustainable issues. There is a decreasing trend in pH of CBMs due to incorporation of SCMs. The determination of numerical values of pH is very important for various low and high volume SCMs blended cement mortars for the better understanding of different defects and durability issues during their service life. In addition, the effect of cement hydration and pozzolanic reaction of SCMs on the pH should be determined at initial and later ages. In this study, the effect of low and high-volume fly ash (FA) and ground granulated ballast furnace slag (GGBFS) cement mortars in different curing conditions on their pH values has been determined. Thermal gravimetric analysis (TGA) was carried out to support the findings from pH measurements. In addition, thermal conductivity (k-value) and strength activity indices of these cement mortars were discussed. The results showed that pH values of all blended cement mortars were less than ordinary Portland cement (OPC) mortar in all curing conditions used. There was a decreasing tendency in pH of all mortars with passage of time. In addition, the pH of cement mortars was not only dependent on the quantity of Ca(OH)2. The effect of adding SCMs on the pH value of cement mortar should be monitored and measured for both short and long terms.

키워드

과제정보

The authors appreciatively acknowledge the support given through the University of Malaya Postgraduate Research Grant (Project No: GPF007F-2019). The author, Sumra Yousuf, also acknowledges the Bahauddin Zakariya University for funding.

참고문헌

  1. Adesina, P.A. and Olutoge, F.A. (2019), "Structural properties of sustainable concrete developed using rice husk ash and hydrated lime", J. Build. Eng., 25, 100804. https://doi.org/10.1016/j.jobe.2019.100804.
  2. Ahmad, M.R., Chen, B., Haque, M.A. and Oderji, S.Y. (2020), "Multiproperty characterization of cleaner and energy-efficient vegetal concrete based on one-part geopolymer binder", J. Clean. Prod., 253, 119916. https://doi.org/10.1016/j.jclepro.2019.119916.
  3. Ahmad, S. (2003), "Reinforcement corrosion in concrete structures, its monitoring and service life prediction-A review", Cement Concrete Compos., 25(4), 459-471. https://doi.org/10.1016/S0958-9465(02)00086-0.
  4. Alarcon-Ruiz, L., Platret, G., Massieu, E. and Ehrlacher, A. (2005), "The use of thermal analysis in assessing the effect of temperature on a cement paste", Cement Concrete Res., 35(3), 609-613. https://doi.org/10.1016/j.cemconres.2004.06.015.
  5. Allahverdi, A., Maleki, A. and Mahinroosta, M. (2018), "Chemical activation of slag-blended Portland cement", J. Build. Eng., 18, 76-83. https://doi.org/10.1016/j.jobe.2018.03.004.
  6. Aprianti, E., Shafigh, P., Zawawi, R. and Abu Hassan, Z.F. (2016), "Introducing an effective curing method for mortar containing high volume cementitious materials", Constr. Build. Mater., 107, 365-377. https://doi.org/10.1016/j.conbuildmat.2015.12.100.
  7. Asadi, I., Shafigh, P., Abu Hassan, Z.F.B. and Mahyuddin, N.B. (2018), "Thermal conductivity of concrete-A review", J. Build. Eng., 20, 81-93. https://doi.org/10.1016/j.jobe.2018.07.002.
  8. ASTM-C150 (2004), Standard Specification for Portland Cement. Annual Book of ASTM Standards, American Society for Testing and Materials, Philadelphia, USA.
  9. Barnett, S., Soutsos, M., Millard, S. and Bungey, J. (2006), "Strength development of mortars containing ground granulated blast-furnace slag: Effect of curing temperature and determination of apparent activation energies", Cement Concrete Res., 36(3), 434-440. https://doi.org/10.1016/j.cemconres.2005.11.002.
  10. Barneyback Jr, R. and Diamond, S. (1981), "Expression and analysis of pore fluids from hardened cement pastes and mortars", Cement Concrete Res., 11(2), 279-285. https://doi.org/10.1016/0008-8846(81)90069-7.
  11. Batis, G., Pantazopoulou, P. and Routoulas, A. (2003), "Corrosion protection investigation of reinforcement by inorganic coating in the presence of alkanolamine-based inhibitor", Cement Concrete Compos., 25(3), 371-377. https://doi.org/10.1016/S0958-9465(02)00061-6.
  12. Bhattacharjee, B. and Krishnamoorthy, S. (2004), "Permeable porosity and thermal conductivity of construction materials", J. Mater. Civil Eng., 16(4), 322-330. https://doi.org/10.1061/(ASCE)0899-1561(2004)16:4(322).
  13. Bickmore, B.R., Nagy, K.L., Gray, A.K. and Brinkerhoff, A.R. (2006), "The effect of Al (OH) 4-on the dissolution rate of quartz", Geochimica et Cosmochimica Acta, 70(2), 290-305. https://doi.org/10.1016/j.gca.2005.09.017.
  14. Bui, P.T., Ogawa, Y., Nakarai, K. and Kawai, K. (2015), "A study on pozzolanic reaction of fly ash cement paste activated by an injection of alkali solution", Constr. Build. Mater., 94, 28-34. https://doi.org/10.1016/j.conbuildmat.2015.06.046.
  15. Carslaw, H.S., and Jaeger, J.C. (1959), Conduction of Heat in Solids, Clarendon Press.
  16. Chindaprasirt, P., Jaturapitakkul, C. and Sinsiri, T. (2005), "Effect of fly ash fineness on compressive strength and pore size of blended cement paste", Cement Concrete Compos., 27(4), 425-428. https://doi.org/10.1016/j.cemconcomp.2004.07.003.
  17. Chore, H. and Joshi, M. (2015), "Strength evaluation of concrete with fly ash and GGBFS as cement replacing materials", Adv. Concrete Constr., 3(3), 223. http://doi.org/10.12989/acc.2015.3.3.223
  18. D5334-08:2014, A. (2014), Standard Test Method for Determination of Thermal Conductivity of Soil and Soft Rock by Thermal Needle Probe Procedure, ASTM International, 5334, 1-8.
  19. Day, K.W., Aldred, J. and Hudson, B., (2013), Concrete Mix Design, Quality Control and Specification, CRC Press.
  20. De la Varga, I., Castro, J., Bentz, D. and Weiss, J. (2012), "Application of internal curing for mixtures containing high volumes of fly ash", Cement Concrete Compos., 34(9), 1001- 1008. https://doi.org/10.1016/j.cemconcomp.2012.06.008.
  21. Djelloul, O.K., Menadi, B., Wardeh, G. and Kenai, S. (2018), "Performance of self-compacting concrete made with coarse and fine recycled concrete aggregates and ground granulated blast-furnace slag", Adv. Concrete Constr., 6(2), 103. http://doi.org/10.12989/acc.2018.6.2.103.
  22. Dove, P.M. (1994), "The dissolution kinetics of quartz in sodium chloride solutions at 25 degrees to 300 degrees C", Am. J. Sci., 294(6), 665-712. https://doi.org/10.2475/ajs.294.6.665
  23. El-Didamony, H., Amer, A.A., Mohammed, M.S. and El-Hakim, M.A. (2019), "Fabrication and properties of autoclaved aerated concrete containing agriculture and industrial solid wastes", J. Build. Eng., 22, 528-538. https://doi.org/10.1016/j.jobe.2019.01.023.
  24. Elahi, A., Basheer, P.A.M., Nanukuttan, S.V. and Khan, Q.U.Z. (2010), "Mechanical and durability properties of high performance concretes containing supplementary cementitious materials", Constr. Build. Mater., 24(3), 292-299. https://doi.org/10.1016/j.conbuildmat.2009.08.045.
  25. Fan, C. and Miller, S.A. (2018), "Reducing greenhouse gas emissions for prescribed concrete compressive strength", Constr. Build. Mater., 167, 918-928. https://doi.org/10.1016/j.conbuildmat.2018.02.092.
  26. Fan, Y., Yin, S., Wen, Z. and Zhong, J. (1999), "Activation of fly ash and its effects on cement properties1", Cement Concrete Res., 29(4), 467-472. https://doi.org/10.1016/S0008-8846(98)00178-1.
  27. Gao, J.M., Qian, C.X., Liu, H.F., Wang, B. and Li, L. (2005), "ITZ microstructure of concrete containing GGBS", Cement Concrete Res., 35(7), 1299-1304. https://doi.org/10.1016/j.cemconres.2004.06.042.
  28. George, R.P. (2012), "Current understanding and future approaches for controlling microbially influenced concrete corrosion: a review", Concrete Res. Lett., 3(3), 491-506.
  29. He, X., Ma, M., Su, Y., Lan, M., Zheng, Z., Wang, T., . . . Zeng, S. (2018), "The effect of ultrahigh volume ultrafine blast furnace slag on the properties of cement pastes", Constr. Build. Mater., 189, 438-447. https://doi.org/10.1016/j.conbuildmat.2018.09.004.
  30. Hilal, A.A. (2016), "Microstructure of concrete", High Performance Concrete Technology and Applications, 3-24.
  31. Hobbs, D. (2001), "Concrete deterioration: causes, diagnosis, and minimising risk", Int. Mater. Rev., 46(3), 117-144. https://doi.org/10.1179/095066001101528420.
  32. Isaia, G.C., Gastaldini, A.L.G. and Moraes, R. (2003), "Physical and pozzolanic action of mineral additions on the mechanical strength of high-performance concrete", Cement Concrete Compos., 25(1), 69-76. https://doi.org/10.1016/S0958-9465(01)00057-9.
  33. Grubb, J.A., Limaye, H.S. and Kakade, A.M. (2007), "Testing pH of concrete", Concrete Int., 29(4), 78-83.
  34. KD2Pro. (2006), KD2 Pro Thermal Properties Analyzer, Operator's Manual, Version 4, Decagon Devices Inc., Pullman, Wash.
  35. Kluitenberg, G., Ham, J. and Bristow, K.L. (1993), "Error analysis of the heat pulse method for measuring soil volumetric heat capacity", Soil Sci. Soc. Am. J., 57(6), 1444-1451. https://doi.org/10.2136/sssaj1993.03615995005700060008x.
  36. Liu, X., Niu, D., Li, X., Lv, Y. and Fu, Q.J.A.S. (2018), "Pore solution pH for the corrosion initiation of rebars embedded in concrete under a long-term natural carbonation reaction", Appl. Sci., 8(1), 128. https://doi.org/10.3390/app8010128.
  37. Lizarazo-Marriaga, J., Claisse, P. and Ganjian, E. (2010), "Effect of steel slag and Portland cement in the rate of hydration and strength of blast furnace slag pastes", J. Mater. Civil Eng., 23(2), 153-160. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000149.
  38. Lo, T.Y., Tang, W.C. and Nadeem, A. (2008), "Comparison of carbonation of lightweight concrete with normal weight concrete at similar strength levels", Constr. Build. Mater., 22(8), 1648-1655. https://doi.org/10.1016/j.conbuildmat.2007.06.006.
  39. Lothenbach, B., Scrivener, K. and Hooton, R.D. (2011), "Supplementary cementitious materials", Cement Concrete Res., 41(12), 1244-1256. https://doi.org/10.1016/j.cemconres.2010.12.001.
  40. Lothenbach, B. and Winnefeld, F. (2006), "Thermodynamic modelling of the hydration of Portland cement", Cement Concrete Res., 36(2), 209-226. https://doi.org/10.1016/j.cemconres.2005.03.001.
  41. Malhotra, V.M. and Mehta, P.K. (2014), Pozzolanic and Cementitious Materials, CRC Press.
  42. Matalkah, F., Salem, T. and Soroushian, P. (2018), "Acid resistance and corrosion protection potential of concrete prepared with alkali aluminosilicate cement", J. Build. Eng., 20, 705-711. https://doi.org/10.1016/j.jobe.2018.08.001.
  43. McPolin, D., Basheer, P. and Long, A. (2009), "Carbonation and pH in mortars manufactured with supplementary cementitious materials", J. Mater. Civil Eng., 21(5), 217-225. https://doi.org/10.1061/(ASCE)0899-1561(2009)21:5(217).
  44. Meyer, C. (2009), "The greening of the concrete industry", Cement Concrete Compos., 31(8), 601-605. https://doi.org/10.1016/j.cemconcomp.2008.12.010.
  45. Mohammed, T.U., Otsuki, N. and Hamada, H. (2003), "Corrosion of steel bars in cracked concrete under marine environment", J. Mater. Civil Eng., 15(5), 460-469. https://doi.org/10.1061/(ASCE)0899-1561(2003)15:5(460).
  46. Mojumdar, S.C. and Janotka, I.J.A.P.S. (2002), "Thermophysical properties of blends from Portland and sulfoaluminate-belite cements", Acta Physica Slovaca, 52(5), 435-446.
  47. Mounanga, P., Khelidj, A., Loukili, A. and Baroghel-Bouny, V. (2004), "Predicting Ca(OH)2 content and chemical shrinkage of hydrating cement pastes using analytical approach", Cement Concrete Res., 34(2), 255-265. https://doi.org/10.1016/j.cemconres.2003.07.006.
  48. Nath, P. and Sarker, P.K. (2014), "Effect of GGBFS on setting, workability and early strength properties of fly ash geopolymer concrete cured in ambient condition", Constr. Build. Mater., 66, 163-171. https://doi.org/10.1016/j.conbuildmat.2014.05.080.
  49. Oner, A. and Akyuz, S. (2007), "An experimental study on optimum usage of GGBS for the compressive strength of concrete", Cement Concrete Compos., 29(6), 505-514. https://doi.org/10.1016/j.cemconcomp.2007.01.001.
  50. Ormellese, M., Berra, M., Bolzoni, F. and Pastore, T. (2006), "Corrosion inhibitors for chlorides induced corrosion in reinforced concrete structures", Cement Concrete Res., 36(3), 536-547. https://doi.org/10.1016/j.cemconres.2005.11.007.
  51. Otieno, M., Beushausen, H. and Alexander, M. (2014), "Effect of chemical composition of slag on chloride penetration resistance of concrete", Cement Concrete Compos., 46, 56-64. https://doi.org/10.1016/j.cemconcomp.2013.11.003.
  52. Pacheco Torgal, F., Miraldo, S., Labrincha, J.A. and De Brito, J. (2012), "An overview on concrete carbonation in the context of eco-efficient construction: evaluation, use of SCMs and/or RAC", Constr. Build. Mater., 36, 141-150. https://doi.org/10.1016/j.conbuildmat.2012.04.066.
  53. Powers, T.C. and Helmuth, R. (1953), Theory of Volume Changes in Hardened Portland-cement Paste during Freezing, Highway Research Board Proceedings.
  54. Ramezanianpour, A.A. and Malhotra, V.M. (1995), "Effect of curing on the compressive strength, resistance to chloride-ion penetration and porosity of concretes incorporating slag, fly ash or silica fume", Cement Concrete Compos., 17(2), 125-133. https://doi.org/10.1016/0958-9465(95)00005-W.
  55. Rashad, A.M. (2015), "An investigation on very high volume slag pastes subjected to elevated temperatures", Constr. Build. Mater., 74, 249-258. https://doi.org/10.1016/j.conbuildmat.2014.10.019.
  56. Roberts, D., Nica, D., Zuo, G. and Davis, J. (2002), "Quantifying microbially induced deterioration of concrete: initial studies", Int. Biodeteriorat. Biodegrad., 49(4), 227-234. https://doi.org/10.1016/S0964-8305(02)00049-5.
  57. Shehata, M.H. and Thomas, M.D.A. (2000), "The effect of fly ash composition on the expansion of concrete due to alkali-silica reaction", Cement Concrete Res., 30(7), 1063-1072. https://doi.org/10.1016/S0008-8846(00)00283-0.
  58. Siddique, R. (2004), "Performance characteristics of high-volume Class F fly ash concrete", Cement Concrete Res., 34(3), 487-493. https://doi.org/10.1016/j.cemconres.2003.09.002.
  59. Siddique, R. and Bennacer, R. (2012), "Use of iron and steel industry by-product (GGBS) in cement paste and mortar", Resour. Conserv. Recyc., 69, 29-34. https://doi.org/10.1016/j.resconrec.2012.09.002.
  60. Siler, P., Kolarova, I., Sehnal, T., Masilko, J. and Opravil, T. (2016), "The determination of the influence of pH value of curing conditions on Portland cement hydration", Procedia Eng., 151, 10-17. https://doi.org/10.1016/j.proeng.2016.07.393.
  61. Standard, B. (1881), Part-116 (1983) Method for Determination of Compressive Strength of Concrete Cubes, London.
  62. Sua-iam, G. and Makul, N. (2017), "Incorporation of high-volume fly ash waste and high-volume recycled alumina waste in the production of self-consolidating concrete", J. Clean. Prod., 159, 194-206. https://doi.org/10.1016/j.jclepro.2017.05.075.
  63. Thomas, M. (2011), "The effect of supplementary cementing materials on alkali-silica reaction: a review", Cement Concrete Res., 41(12), 1224-1231. https://doi.org/10.1016/j.cemconres.2010.11.003
  64. Tong, X.C. (2011), "Characterization methodologies of thermal management materials", Advanced Materials for Thermal Management of Electronic Packaging, Springer New York, New York, NY.
  65. Topcu, I.B. and Canbaz, M. (2007), "Effect of different fibers on the mechanical properties of concrete containing fly ash", Constr. Build. Mater., 21(7), 1486-1491. https://doi.org/10.1016/j.cemconres.2010.11.003.
  66. Wang, H.Y. (2008), "The effects of elevated temperature on cement paste containing GGBFS", Cement Concrete Compos., 30(10), 992-999. https://doi.org/10.1016/j.cemconcomp.2007.12.003.
  67. Xu, H., Liu, Y., Chen, W., Du, R.G. and Lin, C.J. (2009), "Corrosion behavior of reinforcing steel in simulated concrete pore solutions: A scanning micro-reference electrode study", Electrochimica Acta, 54(16), 4067-4072. https://doi.org/10.1016/j.electacta.2009.02.046.
  68. Yahiaoui, W., Kenai, S., Menadi, B. and Kadri, E.H. (2017), "Durability of self compacted concrete containing slag in hot climate", Adv. Concrete Constr., 5(3), 271. http://doi.org/10.12989/acc.2017.5.3.271.
  69. Younsi, A., Turcry, P., Ait-Mokhtar, A. and Staquet, S. (2013), "Accelerated carbonation of concrete with high content of mineral additions: Effect of interactions between hydration and drying", Cement Concrete Res., 43, 25-33. https://doi.org/10.1016/j.cemconres.2012.10.008.
  70. Zhang, W., Min, H., Gu, X., Xi, Y. and Xing, Y. (2015), "Mesoscale model for thermal conductivity of concrete", Constr. Build. Mater., 98, 8-16. https://doi.org/10.1016/j.conbuildmat.2015.08.106.