DOI QR코드

DOI QR Code

Seismic performance of L-shaped RC walls sustaining Unsymmetrical bending

  • Zhang, Zhongwen (Key Laboratory of Concrete and Prestressed Concrete Structures of Ministry of Education, School of Civil Engineering, Southeast University) ;
  • Li, Bing (School of Civil and Environmental Engineering, Nanyang Technological University)
  • Received : 2020.07.30
  • Accepted : 2021.02.19
  • Published : 2021.05.10

Abstract

Reinforced concrete (RC) structural walls with L-shaped sections are commonly used in RC buildings. The walls are often expected to sustain biaxial load and Unsymmetrical bending in an earthquake event. However, there currently exists limited experimental evidence regarding their seismic behaviour in these lateral loading directions. This paper makes experimental and numerical investigations to these walls behaviours. Experimental evidences are presented for four L-shaped wall specimens which were tested under simulated seismic load from different lateral directions. The results highlighted some distinct behaviour of L-shaped walls sustaining Unsymmetrical bending relating to their seismic performance. First, due to the Unsymmetrical bending, out-of-plane reaction forces occur for these walls, which contribute to accumulation of the out-of-plane deformations of the wall, especially when out-of-plane stiffness of the section is reduced by horizontal cracks in the cyclic load. Secondly, cracking was found to affect shear centre of the specimens loaded in the Unsymmetrical bending direction. The shear centre of these specimens distinctly differs in the flange in the positive and negative loading direction. Cracking of the flange also causes significant warping in the bottom part of the wall, which eventually lead to out-of-plane buckling failure.

Keywords

Acknowledgement

This work was financially supported by the National Key R&D Program of China (Grant No.2019YFC1509304) and Natural Science Foundation of Jiangsu Province (BK20190365). The authors wish to express their gratitude for these financial supports.

References

  1. Aaleti, S., Brueggen, B.L., Johnson, B., French, C.E. and Sritharan, S. (2013), "Cyclic response of reinforced concrete walls with different anchorage details: Experimental investigation", ASCE J. Struct. Eng., 139(7), 1181-1191. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000732.
  2. ACI Committee 318 (2011), Building Code Requirements for Structural Concrete (ACI 318-11) and Commentary, American Concrete Institude, Farmington Hills, MI.
  3. Behrouzi, A.A., Mock, A.W., Lehman, D.E., Lowes, L.N. and Kuchma, D.A. (2020), "Impact of bi-directional loading on the seismic performance of C-shaped piers of core walls", Eng. Struct., 225, 111289. https://doi.org/10.1016/j.engstruct.2020.111289.
  4. Boresi, A.P. Schmidt, R.J. and Sidebottom, O.M. (1993), Advanced Mechanics of Materials, John Wiley & Sons, INC., New York.
  5. Brueggen, B.L. (2009), "Performance of T-shaped reinforced concrete structural walls under multi-directional loading", Ph.D. Thesis, University OF Minnesota, Chicago.
  6. CEB-FIP Model Code 1990 (1993), Design of Concrete Structures, CEB-FIP Model Code 1990.
  7. Chang, S.T. (2004), "Shear lag effect in simply supported prestressed concrete box girder", J. Bridge Eng., 9(2), 178-184. https://doi.org/10.1061/(ASCE)1084-0702(2004)9:2(178).
  8. Constantin, R. and Beyer, K. (2016), "Behaviour of U-shaped RC walls under quasi-static cyclic diagonal loading", Eng. Struct., 106, 36-52. https://doi.org/10.1016/j.engstruct.2015.10.018.
  9. Eom, T.S. and Nam, H.S. (2017), "Load contour method for biaxial design of reinforced concrete L-shaped structural walls", Eng. Struct., 146, 148-157. https://doi.org/10.1016/j.engstruct.2017.05.049.
  10. Eurocode 2 (1991), Eurocode 2: Design of Concrete Structures: Part 1-1: General Rules and Rules for Buildings, Final Draft prEN 1998-1, European Committee for Standardization, Brussels, Belgium.
  11. Hassan, M. and El-Tawil, S. (2003), "Tension flange effective width in reinforced concrete shear walls", ACI Struct. J., 100(3), 349-356. https://doi.org/10.14359/12610.
  12. Hoult, R. and Beyer, K. (2020), "Decay of torsional stiffness in rc u-shaped walls", J. Struct. Eng., 146(9), 04020176. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002733.
  13. Hoult, R., Appelle, A., Almeida, J. and Beyer, K. (2020), "Seismic performance of slender RC U-shaped walls with a single-layer of reinforcement", Eng. Struct., 225. https://doi.org/10.1016/j.engstruct.2020.111257.
  14. Hoult, R.D. (2019), "Shear lag effects in reinforced concrete C-shaped walls", J. Struct. Eng., 145(3), 04018270. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002272.
  15. Hoult, R.D., Goldsworthy, H.M. and Lumantarna, E. (2018), "Plastic hinge length for lightly reinforced C-shaped concrete walls", J. Earthq. Eng., 1-32. https://doi.org/10.1080/13632469.2018.1453419.
  16. Inada, K., Chosa, K., Sato, H., Kono, S. and Watanabe, F. (2008,), "Seismic performance of RC L-shaped core structural walls", The 14th World Conference on Earthquake Engineering, October.
  17. Kanishchev, R. and Kvocak, V. (2019), "Local buckling of rectangular steel tubes filled with concrete", Steel Compos. Struct., 31(2), 201-216. https://doi.org/10.1201/9781315393827-26.
  18. Karamlou, A. and Kabir, M. Z. (2012), "Experimental study of L-shaped slender R-ICF shear walls under cyclic lateral loading", Eng. Struct., 36, 134-146. https://doi.org/10.1016/j.engstruct.2011.11.031.
  19. Keihani, R., Bahadori-Jahromi, A. and Goodchild, C. (2019), "The significance of removing shear walls in existing low-rise RC frame buildings - Sustainable approach", Struct. Eng. Mech., 71(5), 563-576. https://doi:10.12989/sem.2019.71.5.563.
  20. Khoshnoud, H.R. and Marsono, K (2016), "Experimental study of masonry infill reinforced concrete frames with and without corner openings", Struct. Eng. Mech., 57(4), 641-656. https://doi.org/10.12989/sem.2016.57.4.641.
  21. Kwan, A.K.H. (1996), "Shear lag in shear/core walls", J. Struct. Eng., 122(9) 1097-1104. https://doi.org/10.1061/(ASCE)0733-9445(1996)122:9(1097).
  22. Kwan, A.K.H. and Cheun, Y.K. (1994), "Analysis of coupled shear/core walls using a beam-type finite element", Eng. Struct., 16(2), 111-118. https://doi.org/10.1016/0141-0296(94)90036-1.
  23. Li, B. and Xiang, W. (2011), "Effective stiffness of squat structural walls", Journal of Structural Engineering, 137(12), 1470-1479. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000386.
  24. Luo, D., Zhang, Z. and Li, B. (2019), "Shear lag effect in steel-concrete composite beam in hogging moment", Steel Compos. Struct., 31(1), 27-41. https://doi.org/10.12989/scs.2019.31.1.027.
  25. Palermo, D. and Vecchio, F.J. (2002), "Behaviour of three-dimensional reinforced concrete shear walls", ACI Struct. J., 99(1), 81-89. https://doi.org/10.3166/isi.9.2.39-60.
  26. Pantazopoulou, S.J. and French, C.W. (2001), "Slab participation in practical earthquake design of reinforced concrete frames", ACI Struct. J., 98(7), 91-104. https://doi.org/10.14359/10291.
  27. Pantazopoulou, S.J. and Moehle, J.P. (1990), "Identification of effect of slabs on flexural behaviour of beams", J. Eng. Mech., 116(1), 91-106. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:7(853).
  28. Paulay, T. and Priestley, M.J.N. (1992), Seismic Design of Reinforced Concrete and Masonry Buildings, John Wiley & Sons, Inc., New York, NY.
  29. Ramirez, J.A., French, C.W., Adebar, P.E., Bonacci, J.F. and Collins, M.P. (1998), "Recent approaches to shear design of structural concrete", J. Struct. Eng., 124(12), 1374. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:7(853).
  30. Selby, R.G. and Vecchio, F.J. (1993), "Three-dimensional constitutive relations for reinforced concrete", Ph.D. Dissertation, Department of Civil Engineering, University of Toronto.
  31. Selby, R.G., Vecchio, F.J. and Collins, M.P. (1996), "Analysis of reinforced concrete members subject to shear and axial compression", ACI Struct. J., 93, 306-315. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:7(853).
  32. Song, Q.G. and Scordelis, A.C. (1990), "Shear-lag analysis of T-, I-, and box beams", J. Struct. Eng., 116(5), 1290-1305. https://doi.org/10.1061/(ASCE)0733-9445(1990)116:5(1290).
  33. Sritharan, S., Beyer, K., Henry, R.S., Chai, Y.H., Kowalsky, M. and Bull, D. (2014), "Understanding poor seismic performance of concrete walls and design implications", Earthq. Spectra, 30(1), 307-334. https://doi.org/10.1193/021713EQS036M.
  34. Thomsen Iv, J.H. and Wallace, J.W. (2004), "Displacement-based design of slender reinforced concrete structural walls-Experimental verification", J. Struct. Eng., 130(4), 618-630. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:4(618).
  35. TNO Diana (2008), Finite Element Analysis User's Manual-Release 9.3, TNO DIANA, Delft, The Netherlands.
  36. Trahair, N.S. (2017), "Flexural-torsional buckling of structures", Routledge.
  37. Vecchio, F.J. (1998), "Lessons from the analysis of a 3-D concrete shear wall", Struct. Eng. Mech., 6(4), 439-455. https://doi.org/10.12989/sem.1998.6.4.439.
  38. Verderame, G.M., Ricci, P. and Di Domenico, M. (2019), "Experimental vs. theoretical out-of-plane seismic response of URM infill walls in RC frames", Struct. Eng. Mech., 69(6), 677-691. https://doi.org/10.12989/sem.2019.69.6.677.
  39. Wallace, J.W. (2012), "Behaviour, design, and modeling of structural walls and coupling beams-Lessons from recent laboratory tests and earthquakes", Int. J. Concrete Struct. Mater., 6(1), 3-18. https://doi.org/10.1007/s40069-012-0001-4.
  40. Waugh, J.D. (2009), "Nonlinear analysis of T-shaped concrete walls subjected to multi-directional displacements", Ph.D. Thesis, University OF Minnesota, Chicago.
  41. Zhang, Z. and Li, B. (2016a), "Seismic performance assessment of slender T-shaped reinforced concrete walls", J. Earthq. Eng., 25, 1-28. https://doi.org/10.1080/13632469.2016.1140097.
  42. Zhang, Z. and Li, B. (2016b), "Effective stiffness of non-rectangular reinforced concrete structural walls", J. Earthq. Eng., 25, 1-22. https://doi.org/10.1080/13632469.2016.1224744.
  43. Zhang, Z., Luo, D. and Li, B. (2020), "Shear lag effect in compressive flange of RC structural walls", ACI Struct. J. (Accepted)