자원리싸이클링 (Resources Recycling)

  • 제30권2호
  • /
  • Pages.24-30
  • /
  • 2021
  • /
  • 2765-3439(pISSN)
  • /
  • 2765-3447(eISSN)
한국자원리싸이클링학회 (The Korean Institute of Resources Recycling)
권호 표지
DOI QR코드

DOI QR Code

염화주석용액을 이용한 폐인쇄회로기판으로부터 부품의 분리

Dismantling of Components from Waste Printed Circuit Boards Using Stannic Chloride Solution

  • 박유진 (한국해양대학교 에너지자원공학과) ;
  • 유경근 (한국해양대학교 에너지자원공학과)
  • Park, Yujin (Department of Energy and Resources Engineering, Korea Maritime and Ocean University) ;
  • Yoo, Kyoungkeun (Department of Energy and Resources Engineering, Korea Maritime and Ocean University)
  • 투고 : 2021.01.08
  • 심사 : 2021.03.02
  • 발행 : 2021.04.30
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

폐인쇄회로기판으로부터 부품을 분리하기 위하여 4가 주석이온 (Sn4+)을 포함한 염산용액을 이용하여 탈착실험을 진행하고, 부품탈착에 대한 교반속도, 반응온도, 4가 주석이온농도, 염산용액농도의 영향을 조사하였다. 100 rpm~300 rpm의 교반속도에서 PCB로부터 부품의 탈착속도는 큰 차이가 없었으며, 반응온도, 4가 주석이온농도, 그리고 염산용액농도를 증가시킴에 따라 탈착속도도 증가하였다. 모든 부품 탈착실험에서 탈착율이 100%에 도달하였을 때 기판에서 솔더는 관찰되지 않았으며 주석농도는 약 1,500 mg/L였다. 10,000 mg/L의 4가 주석이온을 포함한 1 mol/L의 염산용액에 폐하드디스크 PCB 1개를 투입하고, 교반속도와 반응온도를 각각 200 rpm과 90 ℃로 조정한 탈착실험에서 PCB로부터 부품의 탈착은 2시간만에 100% 완료되었다.

Dismantling tests were performed to separate components from waste printed circuit boards (PCBs) using HCl solution with Sn4+. Then, the effects of agitation speed, reaction temperature, initial Sn4+ concentration, and HCl concentration on the dismantling of components were investigated. No significant effect on the dismantling speed was observed upon changing the agitation speed from 100 to 300 rpm. However, the dismantling rate increased with increasing reaction temperature, Sn4+ concentration, and HCl concentration. In the all-component dismantling tests, when the dismantling ratio increased to 100%, no solder was observed on the boards, and the Sn4+ concentration was ~1,500 mg/L. The dismantling ratio of the components from the PCB increased to 100% within 2 h when 1 mol/L HCl solution with 10,000 mg/L Sn4+ was used at an agitation speed and temperature of 200 rpm and 90 ℃, respectively.

키워드

참고문헌

  1. KOREA ELECTRONICS ASSOCIATION, 2006 : HDD market analysis and forecast, Journal of Korean Electronics, 26(10), pp.22-24.
  2. Na, H., Yoo, K., Jha, M. K., et al., 2020 : The separation of aluminum and stainless-steel scraps using vibrating mixed-size ball bed, Metals, 10(7), pp.868. https://doi.org/10.3390/met10070868
  3. Jung, M., Yoo, K., Alorro, R. D., 2017 : Dismantling of Electric and Electronic Components from Waste Printed Circuit Boards by Hydrochloric Acid Leaching with Stannic Ions, Materials Transactions, 58, pp.1076-1080. https://doi.org/10.2320/matertrans.M2017096
  4. Tenorio, J., 1997 : Production of non-ferrous metallic concentrates from electronic scrap, EPD Congress 1997, pp.505-509.
  5. Lee, J., Kim, Y., Lee, J., et al., 2012 : Disassembly of the Mounted Electric/Electronic Components on Wasted Printed Circuit Board and their Characterizations, Journal of The Korean Society of Mineral and Energy Resources Engineers, 49(6), pp.728-735. https://doi.org/10.12972/ksmer.2012.49.6.728
  6. Huang, K., Guo, J., Xu, Z., 2009 : Recycling of waste printed circuit boards: A review of current technologies and treatment status in china, Journal of Hazardous Materials, 164(2-3), pp.399-408. https://doi.org/10.1016/j.jhazmat.2008.08.051
  7. Cayumil, R., Khanna, R., Rajarao, R., et al., 2014 : Generation of copper rich metallic phases from waste printed circuit boards, Waste Management, 34(10), pp.1783-1792. https://doi.org/10.1016/j.wasman.2014.05.004
  8. Havlik, T., Orac, D., Petranikova, M., et al., 2010 : Leaching of copper and tin from used printed circuit boards after thermal treatment, Journal of Hazardous Materials, 183(1-3), pp.866-873. https://doi.org/10.1016/j.jhazmat.2010.07.107
  9. Tickner, J., Rajarao, R., Lovric, B., et al., 2016 : Measurement of gold and other metals in electronic and automotive waste using gamma activation analysis, Journal of Sustainable Metallurgy, 2(4), pp.296-303. https://doi.org/10.1007/s40831-016-0051-y
  10. Kim, E. Y., Kim, M. S., Lee, J. C., et al., 2010 : Leaching behavior of copper using electro-generated chlorine in hydrochloric acid solution, Hydrometallurgy, 100, pp.95-102. https://doi.org/10.1016/j.hydromet.2009.10.009
  11. Kumar, M., Lee, J. C., Kim, M. S., et al., 2014 : Leaching of metals from waste printed circuit boards (wpcbs) using sulfuric and nitric acids, Environmental Engineering & Management Journal (EEMJ), 13(10), pp.2601-2607. https://doi.org/10.30638/eemj.2014.290
  12. Jinglei, Y., Williams, E., Meiting, J., 2009 : Review and prospects of recycling methods for waste printed circuit boards, 2009 IEEE International Symposium on Sustainable Systems and Technology, pp.1-5.
  13. Ilyas, S., Lee, J. C., 2014 : Biometallurgical recovery of metals from waste electrical and electronic equipment: a review, ChemBioEng Reviews, 1(4), pp.148-169. https://doi.org/10.1002/cben.201400001
  14. Chancerel, P., Meskers, C. E., Hageluken, C., et al., 2009 : Assessment of precious metal flows during preprocessing of waste electrical and electronic equipment, Journal of Industrial Ecology, 13(5), pp.791-810. https://doi.org/10.1111/j.1530-9290.2009.00171.x
  15. Lee, J., Kim, Y., Lee, J. C., 2012 : Disassembly and physical separation of electric/electronic components layered in printed circuit boards (PCB), Journal of Hazardous Materials, 241, pp.387-394. https://doi.org/10.1016/j.jhazmat.2012.09.053
  16. Ma, H., Suhling, J. C., 2009 : A review of mechanical properties of lead-free solders for electronic packaging, Journal of Materials Science, 44(5), 1141-1158. https://doi.org/10.1007/s10853-008-3125-9
  17. Yoo, K., Lee, J. C., Lee, K. S., et al., 2012 : Recovery of Sn, Ag and Cu from waste Pb-free solder using nitric acid leaching, Materials Transactions, M2012268.
  18. Kim, S. K., Lee, J. C., Yoo, K., 2016 : Leaching of tin from waste pb-free solder in hydrochloric acid solution with stannic chloride, Hydrometallurgy, 165, pp.143-147. https://doi.org/10.1016/j.hydromet.2015.09.018
  19. Chen, M., Wang, J., Chen, H., et al., 2013 : Electronic waste disassembly with industrial waste heat, Environmental Science & Technology, 47(21), pp.12409-12416. https://doi.org/10.1021/es402102t
  20. Park, S., Kim, S., Han, Y., et al., 2015 : Apparatus for electronic component disassembly from printed circuit board assembly in e-wastes, International Journal of Mineral Processing, 144, pp.11-15. https://doi.org/10.1016/j.minpro.2015.09.013
  21. Zhang, X., Guan, J., Yuan, H., et al., 2017 : Effective dismantling of waste printed circuit board assembly with methanesulfonic acid containing hydrogen peroxide, Environmental Progress & Sustainable Energy, 36(3), pp.873-878. https://doi.org/10.1002/ep.12527
  22. Zhang, X., Guan, J., Guo, Y., et al., 2015 : Selective desoldering separation of tin-lead alloy for dismantling of electronic components from printed circuit boards, ACS Sustainable Chemistry & Engineering, 3(8), pp.1696-1700. https://doi.org/10.1021/acssuschemeng.5b00136

피인용 문헌

  1. Leaching of Copper from Waste-Printed Circuit Boards (PCBs) in Sulfate Medium Using Cupric Ion and Oxygen vol.11, pp.9, 2021, https://doi.org/10.3390/met11091369