Advances in concrete construction

  • 제11권4호
  • /
  • Pages.335-345
  • /
  • 2021
  • /
  • 2287-5301(pISSN)
  • /
  • 2287-531X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Mix design and early-age mechanical properties of ultra-high performance concrete

  • Tang, Chao-Wei (Department of Civil Engineering & Geomatics, Cheng Shiu University)
  • 투고 : 2019.11.21
  • 심사 : 2021.03.20
  • 발행 : 2021.04.25
⟨ 이전 논문 다음 논문 ⟩

초록

It is known from the literature that there are relatively few studies on the engineering properties of ultra-high performance concrete (UHPC) in early age. In fact, in order to ensure the safety of UHPC during construction and sufficient durability and long-term performance, it is necessary to explore the early behavior of UHPC. The test parameters (test control factors) investigated included the percentage of cement replaced by silica fume (SF), the percentage of cement replaced by ultra-fine silica powder (SFP), the amount of steel fiber (volume percent), and the amount of polypropylene fiber (volume percentage). The engineering properties of UHPC in the fresh mixing stage and at the age of 7 days were investigated. These properties include freshly mixed properties (slump, slump flow, and unit weight) and hardened mechanical properties (compressive strength, elastic modulus, flexural strength, and splitting tensile strength). Moreover, the effects of the experimental factors on the performance of the tested UHPC were evaluated by range analysis and variance analysis. The experiment results showed that the compressive strength of the C8 mix at the age of 7 days was highest of 111.5 MPa, and the compressive strength of the C1 mix at the age of 28 days was the highest of 128.1 MPa. In addition, the 28-day compressive strength in each experimental group increased by 13%-34% compared to the 7-day compressive strength. In terms of hardened mechanical properties, the performance of each experimental group was superior to that of the control group (without fiber and without additional binder materials), with considerable improvement, and the experimental group did not produce explosive or brittle damage after the test. Further, the flexural test process found that all test specimens exhibited deflection-hardening behavior, resulting in continued to increase carrying capacity after the first crack.

키워드

참고문헌

  1. Abbas, S., Nehdi, M.L. and Saleem, M. A. (2016), "Ultra-high performance concrete: Mechanical performance, durability, sustainability and implementation challenges", Int. J. Concrete Struct. Mater., 10(3), 271-295. https://doi.org/10.1007/s40069-016-0157-4.
  2. ACI Committee 239 (2012), Meeting Minutes, Am. Concr. Institute, Toronto.
  3. ACI Committee 544 (1982), State of the Art Report of Fiber Reinforced Concrete, Concrete Int., Des. Constr., 4(5), 9-30.
  4. Al-Manaseer, A.A. and Albert, A.J. (1995), "Measuring the consistency and workablity of superplasticized concrete", ACI Mater. J., 92, 286-290.
  5. Alsalman, A., Dang, C.N. and Hale, W.M. (2017), "Development of ultra-high performance concrete with locally available materials", Constr. Build. Mater., 133, 135-145. https://doi.org/10.1016/j.conbuildmat.2016.12.040.
  6. ASTM C138/C138M-17a (2017), Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete, ASTM International, West Conshohocken, PA.
  7. ASTM C143/C143M-15a (2015), Standard Test Method for Slump of Hydraulic-Cement Concrete, ASTM International, West Conshohocken, PA.
  8. ASTM C1611/C1611M-18 (2018), Standard Test Method for Slump Flow of Self-Consolidating Concrete, ASTM International, West Conshohocken, PA.
  9. ASTM C39/C39M-18 (2018), Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens, ASTM International, West Conshohocken, PA.
  10. ASTM C469/C469M-14 (2014), Standard Test Method for Static Modulus of Elasticity and Poisson's Ratio of Concrete in Compression, ASTM International, West Conshohocken, PA.
  11. ASTM C496/C496M-11 (2004), Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens, ASTM International, West Conshohocken, PA.
  12. ASTM C78/C78M-18 (2018), Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading), ASTM International, West Conshohocken, PA.
  13. Azmee, N.M. and Shafiq, N. (2018), "Ultra-high performance concrete: From fundamental to applications", Case Stud. Constr. Mater., 9, e00197. https://doi.org/10.1016/j.cscm.2018.e00197.
  14. Burroughs, J.F., Shannon, J., Rushing, T.S., Yi, K., Gutierrez, Q.B. and Harrelson, D.W. (2017), "Potential of finely ground limestone powder to benefit ultra-high performance concrete mixtures", Constr. Build. Mater., 141, 335-342. https://doi.org/10.1016/j.conbuildmat.2017.02.073.
  15. Erdogdu, S., Kandil, U. and Nayir, S. (2019), "Effects of cement dosage and steel fiber ratio on the mechanical properties of reactive powder concrete", Adv. Concrete Constr., 8(2), 139-144. https://doi.org/10.12989/acc.2019.8.2.139.
  16. Fisher, R.A. (1925), Statistical Methods for Research Workers, Oliver & Boyd, London
  17. Ghafari, E., Arezoumandi, M., Costa, H. and Julio, E. (2015), "Influence of nano-silica addition on durability of UHPC", Constr. Build. Mater., 94, 181-188. https://doi.org/10.1016/j.conbuildmat.2015.07.009.
  18. Gosavi1, J.S. and Awari, U.R. (2018), "A review on high-performance concrete", Int. Res. J. Eng. Technol. (IRJET), 5(5), 1965-1968.
  19. Graybeal, B. (2007), "Compressive behavior of ultra-high performance fiber-reinforced concrete", ACI Mater. J., 104(2), 146-152.
  20. Graybeal, B. (2014), "Ultra-high-performance concrete connections for precast concrete bridge decks", PCI J., 49(4), 48-62. https://doi.org/10.15554/pcij.09012014.48.62
  21. Gu, C., Sun, W., Guo, L., Wang, Q., Liu, J., Yang, Y. and Shi, T. (2018), "Investigation of microstructural damage in ultrahigh-performance concrete under freezing-thawing action", Adv. Mater. Sci. Eng., 2018, Article ID 3701682, 9. https://doi.org/10.1155/2018/3701682.
  22. He, Z.H., Du, S.G. and Chen, D. (2018), "Microstructure of ultra high performance concrete containing lithium slag", J. Hazard. Mater., 5(353), 35-43. https://doi.org/10.1016/j.jhazmat.2018.03.063.
  23. Hughes, B.P. (1977), "Load-deflection curves for fibre-reinforced concrete beams in flexure", Mag. Concrete Res., 29(101), 199-206. https://doi.org/10.1680/macr.1977.29.101.199.
  24. Khaloo, A.R. and Kim, N. (1996), "Mechanical properties of normal to high-strength steel fiber-reinforced concrete", Cement Concrete Aggr., 18(2), 92-97. https://doi.org/10.1520/CCA10156J.
  25. Lai, J., Yang, H., Wang, H. and Zheng, X. (2018), "Properties and modeling of ultra-high-performance concrete subjected to multiple bullet impacts", J. Mater. Civil Eng., 30(10), 04018256. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002462.
  26. Larrard, F. and Sedran, T. (1994), "Optimization of ultra-high performance concrete by the use of a packing model", Cement Concrete Res., 24, 997-1009. https://doi.org/10.1016/0008-8846(94)90022-1.
  27. Larrard, F. and Sedran, T. (2002), "Mixture proportioning of high performance concrete", Cement Concrete Res., 32(11), 1699-1704. https://doi.org/10.1016/S0008-8846(02)00861-X.
  28. Li, P.P., Yu, Q.L. and Brouwers, H.J.H. (2018), "Effect of coarse basalt aggregates on the properties of ultra-high performance concrete (UHPC)", Constr. Build. Mater., 170, 649-659. https://doi.org/10.1016/j.conbuildmat.2018.03.109.
  29. Metha, P.K. and Monteiro, P.J.M. (2006), Concrete; Microstructure, Properties and Materials, 3rd Edition, McGraw-Hill, New York.
  30. Mindess, S. and Bentur, A. (1983), "Concrete beams reinforced with conventional steel bars and steel fibres: properties in static loading", Int. J. Cement Compos. Lightw. Concrete, 5(3), 199-202. https://doi.org/10.1016/0262-5075(83)90007-6
  31. Montgomery, D.C. (2005), Design and Analysis of Experiments, Wiley, New York, NY, USA.
  32. Mosaberpanah, M.A. and Eren, O. (2018), "CO2-full factorial optimization of an ultra-high performance concrete mix design", Eur. J. Environ. Civil Eng., 22(4), 450-463. https://doi.org/10.1080/19648189.2016.1210030.
  33. Myers, J.J. (1999), "How to achieve a higher modulus of elasticity", HPC Bridge Views, FHWA, Sponsored, NCBC Co-Sponsored Newsletter.
  34. Nehdi, M. and Soliman, A.M. (2011), "Early-age properties of concrete: overview of fundamental concepts and state-of-the-art research", Proc. Inst. Civil Eng. Constr. Mater., 164, 57-77. https://doi.org/10.1680/coma.900040.
  35. Neville, A.M. (1994), Properties of Concrete, Longman: Essex, UK.
  36. Okamura, H. and Ozawa, K. (1995), "Mix-design for self-compacting concrete", Concrete Lib. JSCE, 25, 107-120. https://doi.org/10.3151/jact.1.5.
  37. Petersson, O. and Billberg, P. (1996), "A model for selfcompacting concrete", Proc. of the Int. RILEM conf. on production methods and workability of concrete, Paisley, E&FN Spon, London.
  38. Pyo, S. and Kim, H.K. (2017), "Fresh and hardened properties of ultra-high performance concrete incorporating coal bottom ash and slag powder", Constr. Build. Mater., 131, 459-466. https://doi.org/10.1016/j.conbuildmat.2016.10.109.
  39. Pyo, S., Alkaysi, M. and El-Tawil, S. (2016), "Crack propagation speed in ultra high performance concrete (UHPC)", Constr. Build. Mater., 114, 109-118. https://doi.org/10.1016/j.conbuildmat.2016.03.148.
  40. Qu, D., Cai, X. and Chang, W., (2018) "Evaluating the effects of steel fibers on mechanical properties of ultra-high performance concrete using artificial neural networks", Appl. Sci., 8(7), 1120; https://doi.org/10.3390/app8071120.
  41. Rajkumar, P.R.K., Rahul, M. and Ravichandran, P.T. (2018), "Characteristic study on high performance hybrid fiber reinforced concrete using copper slag fine aggregate", Int. J. Eng. Technol., 7(2.33), 31-35.
  42. Sharma, R. and Bansal, P.P. (2019), "Efficacy of supplementary cementitious material and hybrid fiber to develop the ultra high performance hybrid fiber reinforced concrete", Adv. Concrete Constr., 8(1), 21-31. https://doi.org/10.12989/acc.2019.8.1.021
  43. Shi, C., Wu, Z., Xiao, J., Wang, D., Huang, Z. and Fang, Z. (2015), "A review on ultra high performance concrete: part 1. raw materials and mixture design", Constr. Build. Mater., 101, 741-751. https://doi.org/10.1016/j.conbuildmat.2015.10.088.
  44. Soliman, N.A. and Tagnit-Hamou, A. (2016), "Development of ultra-high-performance concrete using glass powder-Towards ecofriendly concrete", Constr. Build. Mater., 125, 600-612. https://doi.org/10.1016/j.conbuildmat.2016.08.073.
  45. Song, P.S. and Hwang, S. (2004), "Mechanical properties of high-strength steel fiber-reinforced concrete", Constr. Build. Mater., 18, 669-673. https://doi.org/10.1016/j.conbuildmat.2004.04.027.
  46. Swamy, R.N. (1976), "The interfacial bond stress in steel fiber cement composites", Cement Concrete Res., 6(5), 641-650. https://doi.org/10.1016/0008-8846(76)90028-4.
  47. Taguchi, G. (1987), Introduction to Quality Engineering: Designing Quality into Products and Processes, Asian Productivity Organization, Tokyo, Japan.
  48. Talebinejad, I., Iranmanesh, A., Bassam, S. and Shekarchizadeh, M. (2004), "Optimizing mix proportions of normal weight reactive powder concrete with strengths of 200-350 MPa", Proceedings of the International Symposium on UHPC, Kassel, Germany.
  49. Tattersall, G.H. (1979), "Concrete: A multi-phase system", Concrete, January.
  50. Velazco, G., Visalvanich, K. and Shah, S.P. (1980), "Fracture behavior and analysis of fiber reinforced concrete beams", Cement Concrete Res., 10(1), 41-51. https://doi.org/10.1016/0008-8846(80)90050-2.
  51. Wille, K., Naaman, A. and Montesinos, G. (2011), "Ultra-high performance concrete with compressive strength exceeding 150 MPa (22 ksi): a simpler way", ACI Mater. J., 108(1), 46-54.
  52. Yu, R., Spiesz, P. and Brouwers, H. (2014), "Mix design and properties assessment of Ultra-high performance fibre reinforced concrete (UHPFRC)", Cement Concrete Res., 56, 29-39. https://doi.org/10.1016/j.cemconres.2013.11.002.
  53. Zhou, Y., Xi, B., Yu, K., Sui, L. and Xing, F. (2018), "Mechanical properties of hybrid ultra-high performance engineered cementitous composites incorporating steel and polyethylene fibers", Mater., 11, 1448. https://doi.org/10.3390/ma11081448.