Advances in concrete construction

  • 제11권4호
  • /
  • Pages.271-284
  • /
  • 2021
  • /
  • 2287-5301(pISSN)
  • /
  • 2287-531X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Behavior of reinforced sustainable concrete hollow-core slabs

  • Al-Azzawi, Adel A. (Department of Civil Engineering, Al-Nahrain University) ;
  • Shallal, Mustafa S. (Department of Civil Engineering, Al-Nahrain University)
  • 투고 : 2018.12.29
  • 심사 : 2021.02.10
  • 발행 : 2021.04.25
⟨ 이전 논문 다음 논문 ⟩

초록

This study aims to trace the response of twelve one-way sustainable concrete hollow-core slabs made by reducing cement content and using replacement of coarse aggregate by plastic aggregate. The trial mixes comprise the 25, 50, 75, and 100% replacement of natural coarse aggregate. The compressive strength of the resulting lightweight concrete with full replacement of coarse aggregate by plastic aggregate was 28 MPa. These slabs are considered to have a reduced dead weight due to using lightweight aggregate and due to reducing cross-section through using voids. The samples are tested under two verticals line loads. Several parameters are varied in this study such as; nature of coarse aggregate (natural or recycled), slab line load location, the shape of the core, core diameter, flexural reinforcement ratio, and thickness of the slab. Strain gauges are used in the present study to measure the strain of steel in each slab. The test samples were fourteen one-way reinforced concrete slabs. The slab's dimensions are (1000 mm), (600 mm), (200 mm), (length, width, and thickness). The change in the shape of the core from circular to square and the use of (100 mm) side length led to reducing the weight by about (46%). The cracking and ultimate strength is reduced by about (5%-6%) respectively. With similar values of deflection. The mode of failure will remain flexural. It is recognized that when the thickness of the slab changed from (200 mm to 175 mm) the result shows a reduction in cracking and ultimate strength by about (6% and 7%) respectively.

키워드

참고문헌

  1. Abramski, M., Albert, A., Nitsch, A. and Schnell, J. (2010), "Bearing behavior of biaxial hollow core slabs", 34th International Symposium on Bridge and Structural Engineering, Venice, January.
  2. ACI 211.1 (1991), Standard Practice for Selecting Proportions for Normal, Heavyweight and Mass Concrete, American Concrete Institute, 6-38.
  3. ACI 213R-03 (2003), Guide for Structural Lightweight-Aggregate Concrete, American Concrete Institute, Detroit, U.S.A.
  4. ACI318-14, (2014), Building Code Requirements for Structural Concrete and Commentary, American Concrete Institute, Detroit, U.S.A.
  5. Al-Azzawi, A.A. and Abdul Al-Aziz, B.A. (2018), "Behavior of reinforced lightweight aggregate concrete hollow core slabs", Comput. Concrete, 21(2), 117-126. https://doi.org/10.12989/cac.2018.21.2.117.
  6. Al-Azzawi, A.A. and Abed, S.A. (2017), "Investigation of the behavior of reinforced concrete hollow-core thick slabs", Comput. Concrete, 19(5), 567-577. https://doi.org/10.12989/cac.2017.19.5.567.
  7. Al-Azzawi, A.A. and Al-Asdi, A.J. (2017), "Behavior of one way reinforced concrete slabs with styropor blocks", Adv. Concrete Constr., 5(5), 451-468. http://dx.doi.org/10.12989/acc.2017.5.5.451.
  8. Al-Azzawi, A.A. and Al-Azzawi, A.A. (2020), "Mechanical properties of green concrete", IOP Conf. Ser.: Mater. Sci. Eng., 888(1), 012022. https://doi.org/10.1088/1757-899X/888/1/012022.
  9. Al-Azzawi, A.A., Daud, R.A. and Daud, S.A. (2020), "Behavior of tension lap spliced sustainable concrete flexural members", Adv. Concrete Constr., 9(1), 83-92. https://doi.org/10.12989/acc.2020.9.1.083.
  10. Alamgir, M. and Ahsan, A. (2007), "Municipal solid waste and recovery potential: Bangladesh perspective", Iran. J. Environ. Hlth. Sci. Eng., 4(2), 67-76.
  11. ASTM C 1240 (2005), Standard Specification for Silica Fume Used in Cementitious Mixtures, American Society for Testing and Material.
  12. Brunesi, E., Bolognini, D. and Nascimbene, R. (2014), "Evaluation of the shear of precast-prestressed hollow core slab: numerical and experimental comparison", Mater. Struct., 48(5), 1503-1521. https://doi.org/10.1617/s11527-014-0250-6.
  13. Daud, R.A., Cunningham, L.S. and Wang, Y.C. (2015), "Static and fatigue behaviour of the bond interface between concrete and externally bonded CFRP in single shear", Eng. Struct., 97, 54-67. https://doi.org/10.1016/j.engstruct.2015.03.068.
  14. Daud, S.A., Forth, J.P. and Nikitas, N. (2018), "Time-dependent behaviour of cracked, partially bonded reinforced concrete beams under repeated and sustained loads", Eng. Struct., 163, 267-280. https://doi.org/10.1016/j.engstruct.2018.02.054.
  15. de Brito, J. and Saikia, N. (2013), Recycled Aggregate in Concrete, Springer-Verlag, London.
  16. Haruna, S.I. (2014), "Flexural behavior of precast pre-stressed concrete hollow core slabs with cast-in-place concrete topping", Master's Thesis, Civil Engineering, Atilim University.
  17. Iraqi Specification No. 45 (1984), Aggregate from Natural Sources for Concrete, Central Agency for Standardization and Quality Control, Planning Council, Baghdad, Iraq.
  18. Iraqi Specification No.5 (1984), Portland Cement, Central Agency for Standardization and Quality Control, Planning Council, Baghdad, Iraq.
  19. Khalid, F.S., Irwan, J.M., Ibrahim, M.H.W., Othman, N. and Shahidan, S. (2018), "Performance of plastic wastes in fiber-reinforced concrete beams", Constr. Build. Mater., 183, 451-464. https://doi.org/10.1016/j.conbuildmat.2018.06.122.
  20. Khatib, J., Jahami, A., Elkordi, A. and Baalbaki, O. (2019), "Structural performance of reinforced concrete beams containing plastic waste caps", Mag. Civil Eng., 91(7), 73-79. https://doi.org/10.18720/MCE.91.7.
  21. Lee, D.H., Park, M., Oh, J., Kim, K.S., Im, J. and Seo, S. (2014), "Web-shear capacity of prestressed hollow core slab unit with consideration on the minimum shear reinforcement requirement", Comput. Concrete, 14(3), 211-231. https://doi.org/10.12989/cac.2014.14.3.211.
  22. Mohammed, A.A. (2017), "Flexural behavior and analysis of reinforced concrete beams made of recycled PET waste concrete", Constr. Build. Mater., 155, 593-604. https://doi.org/10.1016/j.conbuildmat.2017.08.096.
  23. Rahman, M.K., Baluch, M.H., Said, M.K. and Shazali, M.A. (2012), "Flexural and shear strength of pre-stressed precast hollow-core slabs", Arab. J. Sci. Eng., 37(2), 443-455. https://doi.org/10.1007/s13369-012-0175-8
  24. Said, M.K., Rahman, M.K. and Baluch, M.K. (2012), "Analysis and design of prestressed precast hollow core slabs using strut and tie method", Arab. J. Sci. Eng., 37, 457-468. https://doi.org/10.1007/s13369-012-0179-4
  25. Stephen, C. (2013), "Hollow core manufacturing and factory design", Ind. Concrete J., 20-25.
  26. Wariyatno, N.G., Haryanto, Y. and Sudiboyo, G.H. (2017), "Flexural behavior of precast hollow core slab using PVC pipe and Styrofoam with different reinforcement", Procedia Eng., 171, 909-916. https://doi.org/10.1016/j.proeng.2017.01.388.
  27. Yang, X., Yao, Y., Chu, Y. and Yang, T. (2014), "Study on the calculation method for flexural capacity of pre-stressed concrete hollow-core slabs strengthened with CFRP", Appl. Mech. Mater., 578-579, 1366-1369. https://doi.org/10.4028/www.scientific.net/AMM.578-579.1366.