Steel and Composite Structures

  • 제38권4호
  • /
  • Pages.399-414
  • /
  • 2021
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Research on shear distribution of perfobond connector groups with rubber rings

  • Liu, Yangqing (Department of Bridge Engineering, Tongji University) ;
  • Xin, Haohui (Department of Bridge Engineering, Tongji University) ;
  • Liu, Yuqing (Department of Bridge Engineering, Tongji University)
  • 투고 : 2019.07.16
  • 심사 : 2021.01.28
  • 발행 : 2021.02.25
⟨ 이전 논문 다음 논문 ⟩

초록

This paper aims to verify the feasibility of rubber rings to mitigate the shear concentration in perfobond connector (PBL) groups. Firstly, modified push-out tests for five specimens with four holes were conducted to investigate the effects of rubber rings on the shear mechanism of PBL groups. The test results showed that by employing rubber rings on partial holes, more shear forces were distributed to the holes without rubber rings. The rubber rings significantly improved the slip ability of the specimens, and the ductility of PBL groups is dependent on the number and thickness of rubber rings. Subsequently, three-dimensional numerical models were established and validated by the experimental results. According to the plastic strain distribution in concrete dowels, the action principle of rubber rings in PBL groups was explained. Furthermore, the parametric study was conducted to investigate the influential factors on shear distributions, including the width of steel plates, the hole spacing, the number of holes, the rubber ring thickness, and the positions of rubber rings. The parametric analysis results showed that the redistribution of shear forces is significantly affected by the rubber rings with the smallest thickness. By properly employing rubber rings in PBL groups, the shear forces of holes are more even. Finally, an analytical model for PBL groups with rubber rings was proposed to predict the shear distribution at the serviceability stage.

키워드

참고문헌

  1. ABAQUS Documentation. Version 6.12. (2012), Dassault system, USA.
  2. Ahn, J.H., et al. (2010), "Shear resistance of the perfobond-rib shear connector depending on concrete strength and rib arrangement", J. Constr. Steel Res., 66(10), 1295-1307. https://doi.org/10.1016/j.jcsr.2010.04.008.
  3. Al-Darzi, S.Y.K., Chen, A.R. and Liu, Y.Q. (2007), "Finite element simulation and parametric studies of perfobond rib connector", Am. J. Appl. Sci., 4(3), 122-127. https://doi.org/10.3844/ajassp.2007.122.127
  4. Allahyari, H., Dehestani, M., Beygi, M.H., Neya, B.N. and Rahmani, E. (2014), "Mechanical behavior of steel-concrete composite decks with perfobond shear connectors", Steel Compos. Struct., 17(3), 339-358. http://dx.doi.org/10.12989/scs.2014.17.3.339.
  5. Candido-Martins, J.P.S., Costa-Neves, L.F. and Vellasco, P.D.S. (2010), "Experimental evaluation of the structural response of Perfobond shear connectors", Eng. Struct., 32(8), 1976-1985. https://doi.org/10.1016/j.engstruct.2010.02.031.
  6. CEB-FIP Model Code 2010, (2010), British Standard Institution.
  7. Classen, M. and Hegger, J. (2017), "Shear-slip behaviour and ductility of composite dowel connectors with pry-out failure", Eng. Struct., 50, 428-437. https://doi.org/10.1016/j.engstruct.2017.07.065.
  8. Classen, M. (2018), "Limitations on the use of partial shear connection in composite beams with steel T-sections and uniformly spaced rib shear connectors", J. Constr. Steel Res., 142, 99-112. https://doi.org/10.1016/j.jcsr.2017.11.023.
  9. EUROCODE 4, EN 1994-1-1, (2005), Design of Composite Steel and Concrete Structures Part 1.1 General Rules and Rules for Buildings, CEN-European Committee for Standardization, Brussels.
  10. Hechler, O., Berthellemy, J., Lorenc, W., Seidl, G. and Viefhues, E. (2011), Continuous shear connectors in bridge construction. In Composite Construction in Steel and Concrete VI (pp. 78-91).
  11. Khorramian, K., Maleki, S., Shariati, M., Jalali, A. and Tahir, M.M. (2017), "Numerical analysis of tilted angle shear connectors in steel-concrete composite systems", Steel Compos. Struct., 23(1), 67-85. https://doi.org/10.12989/scs.2017.23.1.067.
  12. Kim, K.S., Han, O., Gombosuren, M. and Kim, S.H. (2019), "Numerical simulation of Y-type perfobond rib shear connectors using finite element analysis", Steel Compos. Struct., 31(1), 53-67. https://doi.org/10.12989/scs.2019.31.1.053.
  13. Kim, S.H., Lee, C.G., Ahn, J.H. and Won, J.H. (2011), "Experimental study on joint of spliced steel-PSC hybrid girder, Part I: Proposed parallel-perfobond-rib-type joint", Eng. Struct., 33(8), 2382-2397. https://doi.org/10.1016/j.engstruct.2011.04.012.
  14. Kraus, D. and Wurzer, O. (1997), "Nonlinear finite-element analysis of concrete dowels", Comput. Struct., 64(5-6), 1271-1279. https://doi.org/10.1016/S0045-7949(97)00034-5.
  15. Liu, Y., Xin, H. and Liu, Y. (2018), "Load transfer mechanism and fatigue performance evaluation of suspender-girder composite anchorage joints at serviceability stage", J. Constr. Steel Res., 145, 82-96. https://doi.org/10.1016/j.jcsr.2018.02.010.
  16. Liu, Y., Xin, H. and Liu, Y. (2019), "Experimental and analytical study on shear mechanism of rubber-ring perfobond connector", Eng. Struct., 197, 109382. https://doi.org/10.1016/j.engstruct.2019.109382.
  17. Nguyen, H.T. and Kim, S.E. (2009), "Finite element modeling of push-out tests for large stud shear connectors", J. Constr. Steel Res., 65(10-11), 1909-1920. https://doi.org/10.1016/j.jcsr.2009.06.010.
  18. Oguejiofor, E.C. and Hosain, M.U. (1994), "A parametric study of perfobond rib shear connectors", Can. J. Civil Eng., 21(4), 614-625. https://doi.org/10.1139/l94-063.
  19. Pavlovic, M., Markovic, Z., Veljkovic, M. and Budevac, D. (2013), "Bolted shear connectors vs. headed studs behaviour in push-out tests", J. Constr. Steel Res., 88, 134-149. https://doi.org/10.1016/j.jcsr.2013.05.003.
  20. Spremic, M., Pavlovic, M., Markovic, Z., Veljkovic, M. and Budjevac, D. (2018), "FE validation of the equivalent diameter calculation model for grouped headed studs", Steel Compos. Struct., 26(3), 375-386. https://doi.org/10.12989/scs.2018.26.3.375.
  21. Zheng, S., et al. (2016), "Parametric study on shear capacity of circular-hole and long-hole perfobond shear connector", J. Constr. Steel Res., 117, 64-80. https://doi.org/10.1016/j.jcsr.2015.09.012.