Composites Research

  • 제34권1호
  • /
  • Pages.35-46
  • /
  • 2021
  • /
  • 2288-2103(pISSN)
  • /
  • 2288-2111(eISSN)
한국복합재료학회 (The Korean Society for Composite Materials)
권호 표지
DOI QR코드

DOI QR Code

복합소재를 활용한 B필러 강화재의 구조해석 및 설계

Structural Analysis and Design of B-pillar Reinforcement using Composite Materials

  • 투고 : 2020.12.28
  • 심사 : 2021.02.16
  • 발행 : 2021.02.28
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

본 논문은 차량에 사용되는 B필러의 강화재를 기존의 스틸 소재에서 CFRP(Carbon Fiber Reinforced Plastics)와 GFRP(Glass Fiber Reinforced Plastics)로 대체하여 경량화하는 것이 목표다. 이를 위해서는 무게는 감소시키면서 기존 B필러를 대체할 수 있는 구조안정성을 확보해야 한다. 기존 B필러는 스틸 아우터(outer)를 포함하여 다양한 형상의 스틸 강화재로 구성되며, 이와 같은 스틸 강화재 중 2가지의 스틸 강화재를 복합재로 대체하고자 한다. 이와 같은 스틸 강화재는 강화재 각각을 따로 제작하여 용접을 통해 결합되지만, 복합재 강화재는 패치(patch) 형태의 CFRP와 리브(rib) 구조의 GFRP를 활용하여 압축과 사출 공정을 통해 한번에 제작된다. CFRP는 B필러의 고강도부에 부착되어 측면 하중에 저항하도록 하였으며, GFRP 리브는 위상 최적화(Topology optimization) 기법을 통해 비틀림과 측면 하중을 저항하도록 설계하였다. 구조해석을 통해 기존 스틸 강화재와 비교 분석을 수행하였고, 경량화율을 산출하였다.

This paper aims to reduce weight by replacing the reinforcements of the B-pillar used in vehicles with CFRP(Carbon Fiber Reinforced Plastics) and GFRP(Glass Fiber Reinforced Plastics) from the existing steel materials. For this, it is necessary to secure structural stability that can replace the existing B-pillar while reducing the weight. Existing B-pillar are composed of steel reinforcements of various shapes, including a steel outer. Among these steel reinforcements, two steel reinforcements are to be replaced with composite materials. Each steel reinforcement is manufactured separately and bonded to the B-pillar outer by welding. However, the composite reinforcements presented in this paper are manufactured at once through compression and injection processes using patch-type CFRP and rib-structured GFRP. CFRP is attached to the high-strength part of the B-pillar to resist side loads, and the GFRP ribs are designed to resist torsion and side loads through a topology optimization technique. Through structural analysis, the designed composite B-pillar was compared with the existing B-pillar, and the weight reduction ratio was calculated.

키워드

참고문헌

  1. Hwang, Y.T., Lim, J.Y., Nam, B.G., and Kim, H.S., "Analytical Prediction and Validation of Elastic Behavior of Carbon-Fiber-Reinforced Woven Composites," Composites Research, Vol. 31, No. 5, 2018, pp. 276-281.
  2. Moon, J.B., Kim, J.H., Jang, H.K., and Park, J.S., "A Study on Calculation of Composites Lamina Material Properties through Reverse Engineering of Light Weight Composite Car-body," Transaction of the Korean Society of Automotive Engineers, Vol. 25, No. 1, 2017, pp. 1-10. https://doi.org/10.7467/KSAE.2017.25.1.001
  3. Kim, G.H., Lim, D.W., Choi, J.H., Kweon, J.H., Lee, T.J., Song, M.H., and Shin, S.J., "Fabrication and Evaluation of Composite Panel with Hat-shaped Stiffeners," Composites Research, Vol. 23, No. 2, 2010, pp. 31-39. https://doi.org/10.7234/kscm.2010.23.2.031
  4. Lee, J.J., Mun, J.H., Yoon, W.H., Kang, D.K., Ahn, M.S., Roh, H.J., Kang, J.H., and Lee, J.W., "Study on Structural Reliability Assessment of a Partition Panel Made of a CFRP(Carbon Fiber Reinforced Plastic)," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 18, No. 10, 2019, pp. 68-74. https://doi.org/10.14775/ksmpe.2019.18.10.068
  5. Shin, K.B., and Koo, D.H., "A Study on the Evaluation of the Failure for Carbody Structures made of Laminated Fiber-Reinforced Composite Materials Using Total Laminate Approach," Composites Research, Vol. 17, No. 1, 2004, pp. 18-28.
  6. UN_IPRES Corp., "Total Press Engineering - Unipres' Technical Strength homepage", accessed Dec. 12, 2020, www.unipres.co.jp/en/products/total/
  7. Behrens, B.A., Bouguecha, A., Gaebel, C.M., Moritz, J., and Schrödter, J., "Hot Stamping of Load Adjusted Structural Parts," Proceeding of the 11th International Conference on Technology of Plasticity, Nagoya, Japan, Oct. 2014, pp. 1756-1761.
  8. Nam, K.W., Park, S.H., Yoo, J.S., and Lee, S.M., "Analysis of Impact Characteristics of Bonded Dissimilar Materials for Center Pillar," Transactions of the Korean Society of Mechanical Engineers-A, Vol. 36, No. 8, 2012, pp. 929-934. https://doi.org/10.3795/KSME-A.2012.36.8.929
  9. Lee, I.C., Lee, T.K., and Jang, D.H., "Development Process of Side Impact Beam for Automotive Light-Weighting Door using Sheet Type," Transactions of Materials Processing, Vol. 24, No. 2, 2015, pp. 130-137. https://doi.org/10.5228/KSTP.2015.24.2.130
  10. Nam, K.W., Park, S.H., Lee, K.H., and Lee, M.Y., "Mechanical Properties of Laser-Welded Multi-Material Tailor-Welded Blanks," Transactions of the Korean Society of Mechanical Engineers-A, Vol. 36, No. 8, 2012, pp. 857-863.
  11. Toeh, E.R., and Lund, A.K., "IIHS Side Crash Test Ratings and Occupant Death Risk in Real-World Crashes," Traffic Injury Prevention, Vol. 12, No. 5, 2011, pp. 500-507. https://doi.org/10.1080/15389588.2011.585671
  12. Ghadianlou, A., and Abdullag, S.B., "Crashworthiness Design of Vehicle Side Door Beams under Low-speed Pole Side Impacts," Thin-Walled Structures, Vol. 67, 2013, pp. 25-33. https://doi.org/10.1016/j.tws.2013.02.004
  13. Hill, R., "A Theory of the Yielding and Plastic Flow of Anisotropic Metals," Proceeding of the Royal Society, Series A, Vol. 193, 1948.