Structural Engineering and Mechanics

  • 제77권1호
  • /
  • Pages.1-17
  • /
  • 2021
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Influence of prestressing on the behavior of uncracked concrete beams with a parabolic bonded tendon

  • Bonopera, Marco (Bridge Engineering Division, National Center for Research on Earthquake Engineering) ;
  • Chang, Kuo-Chun (Department of Civil Engineering, National Taiwan University) ;
  • Lin, Tzu-Kang (Department of Civil Engineering, National Chiao Tung University) ;
  • Tullini, Nerio (Department of Engineering, University of Ferrara)
  • 투고 : 2019.03.12
  • 심사 : 2020.08.28
  • 발행 : 2021.01.10
⟨ 이전 논문 다음 논문 ⟩

초록

The influence of prestress force on the fundamental frequency and static deflection shape of uncracked Prestressed Concrete (PC) beams with a parabolic bonded tendon was examined in this paper. Due to the conflicts among existing theories, the analytical solutions for properly considering the dynamic and static behavior of these members is not straightforward. A series of experiments were conducted for a total period of approximately 2.5 months on a PC beam made with high strength concrete, subsequently and closely to the 28 days of age of concrete. Specifically, the simply supported PC member was short term subjected to free transverse vibration and three-point bending tests during its early-age. Subsequently, the experimental data were compared with a model that describes the dynamic behavior of PC girders as a combination of two substructures interconnected, i.e., a compressed Euler-Bernoulli beam and a tensioned parabolic cable. It was established that the fundamental frequency of uncracked PC beams with a parabolic bonded tendon is sensitive to the variation of the initial elastic modulus of concrete in the early-age curing. Furthermore, the small variation in experimental frequency with time makes doubtful its use in inverse problem identifications. Conversely, the relationship between prestress force and static deflection shape is well described by the magnification factor formula of the "compression-softening" theory by assuming the variation of the chord elastic modulus of concrete with time.

키워드

과제정보

Experiments were supported by funding from the National Applied Research Laboratories Project of Taiwan (NCREE-06107A1700). M.B. gratefully acknowledges the funding provided by the Ministry of Science and Technology of Taiwan (MOST 106-2811-E-492-001). N.T. acknowledges the financial support of the "Research Program FAR 2020" provided by the University of Ferrara. A special thank is extended to our technicians of NCREE, and to the students of National Chiao Tung University who furnished assistance to the authors.

참고문헌

  1. ACI 318 (2019), Building Code Requirements for Structural Concrete and Commentary, American Concrete Institute; Farmington Hills, MI, USA.
  2. Annual Book of ASTM Standards (2016), Section 4: Construction vol. 04.02. Concrete and Aggregates, American Society for Testing & Materials.
  3. Bazant, Z.P. and Cedolin, L. (1991), Stability of Structures, Oxford University Press, New York, USA.
  4. Bazant, Z.P., Jirasek, M., Hubler, M.H. and Carol, I. (2015), "RILEM draft recommendation: TC-242-MDC multi-decade creep and shrinkage of concrete: material model and structural analysis. Model B4 for creep, drying shrinkage and autogenous shrinkage of normal and high-strength concretes with multi-decade applicability", Mater. Struct., 48(4), 753-770. http://dx.doi.org/10.1617/s11527-014-0485-2.
  5. Bonopera, M., Chang, K.C., Chen, C.C., Lin, T.K. and Tullini, N. (2018a), "Compressive column load identification in steel space frames using second-order deflection-based methods", Int. J. Struct. Stab. Dy., 18(7), 1-16, 1850092. https://doi.org/10.1142/S021945541850092X.
  6. Bonopera, M., Chang, K.C., Chen, C.C., Lee, Z.K. and Tullini, N. (2018b), "Axial load detection in compressed steel beams using FBG-DSM sensors", Smart Struct. Syst., 21(1), 53-64. https://doi.org/10.12989/sss.2018.21.1.053
  7. Bonopera, M., Chang, K.C., Chen, C.C., Sung, Y.C. and Tullini, N. (2018c), "Feasibility study of prestress force prediction for concrete beams using second-order deflections", Int. J. Struct. Stab. Dy., 18(10), 1-19, 1850124. https://doi.org/10.1142/S0219455418501249
  8. Bonopera, M., Chang, K.C., Chen, C.C., Sung, Y.C. and Tullini, N. (2018d), "Prestress force effect on fundamental frequency and deflection shape of PCI beams", Struct. Eng. Mech., 67(3), 255-265. https://doi.org/10.12989/sem.2018.67.3.255
  9. Bonopera, M., Chang, K.C., Chen, C.C., Lin, T.K. and Tullini, N. (2018e), "Bending tests for the structural safety assessment of space truss members", Int. J. Space Struct., 33(3-4), 138-149. https://doi.org/10.1177/266351118804123.
  10. Bonopera, M., Chang, K.C., Chen, C.C., Sung, Y.C. and Tullini, N. (2019a), "Experimental study on the fundamental frequency of prestressed concrete bridge beams with parabolic unbonded tendons", J. Sound Vib., 455, 150-160. https://doi.org/10.1016/j.jsv.2019.04.038.
  11. Bonopera, M., Chang, K.C., Chen, C.C., Lee, Z.K., Sung, Y.C. and Tullini, N. (2019b), "Fiber Bragg grating-differential settlement measurement system for bridge displacement monitoring: Case study", J. Bridge Eng., 24(10), 1-12, 05019011. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001470.
  12. Breccolotti, M. (2018), "On the evaluation of prestress loss in PRC beams by means of dynamic techniques", Int. J. Concr. Struct. Mater., 12(1). https://doi.org/10.1186/s40069-018-0237-8.
  13. BS EN 12812 (2008), Falsework - Performance Requirements and General Design, British Standards Institution.
  14. CEB (1993), CEB-FIP Model Code 1990, CEB Bulletin d'Information No. 213/214, Comite Euro-International du Beton, Lausanne, Switzerland, 33-41.
  15. Chin, W.Y. and Chern, J.C. (2018), "Establishment of B4-TW prediction model for concrete deformation in Taiwan (II): drying shrinkage, autogenous shrinkage and total shrinkage", Struct. Eng., 33(3), 65-86 (in Chinese).
  16. Deak, G. (1996), "Discussion on prestress force effect on vibration frequency of concrete bridges", J. Struct. Eng., 458-459.
  17. Gan, B.Z., Chiew, S.P., Lu, Y. and Fung, T.C. (2019), "The effect of prestressing force on natural frequencies of concrete beams - A numerical validation of existing experiments by modelling shrinkage crack closure", J. Sound Vib., 455, 20-31. https://doi.org/10.1016/j.jsv.2019.04.030.
  18. Hamed, E. and Frostig, Y. (2006), "Natural frequencies of bonded and unbonded pre-stressed beams pre-stress force effects", J. Sound Vib., 295(1-2), 28-39. https://doi.org/10.1016/j.jsv.2005.11.032.
  19. Haque, M.N. and Kayali, O. (1998), "Properties of high-strength concrete using a fine fly ash", Cem. Concr. Res., 28(10), 1445-1452. https://doi.org/10.1016/S0008-8846(98)00125-2.
  20. Hop, T. (1991), "The effect of degree of prestressing and age of concrete beams on frequency and damping of their free vibration", Mater. Struct., 24, 210-220. https://doi.org/10.1007/BF02472987
  21. Hsiao, J.K. (2017), "Prestress loss distributions along simply supported pretensioned concrete beams", Electron. J. Struct. Eng., 16, 18-25. https://doi.org/10.56748/ejse.16207
  22. Jain, S.K. and Goel, S.C. (1996), "Discussion on prestress force effect on vibration frequency of concrete bridges", J. Struct. Eng., 459-460. https://doi.org/10.1061/(ASCE)0733-9445(1996)122:4(458).
  23. Jaiswal, O.R. (2008), "Effect of prestressing on the first flexural natural frequency of beams", Struct. Eng. Mech., 28(5), 515-524. https://doi.org/10.12989/sem.2008.28.5.515.
  24. Jerath, S. and Shibani, M.M. (1984), "Dynamic modulus for reinforced concrete beams", J. Struct. Eng., 110(6), 1405-1410. https://doi.org/10.1061/(ASCE)0733-9445(1984)110:6(1405)
  25. Kato, M. and Shimada, S. (1986), "Vibration of PC bridges during failure process", J. Struct. Div., 112(7), 1692-1703. https://doi.org/10.1061/(ASCE)0733-9445(1986)112:7(1692)
  26. Kernicky, T., Whelan, M. and Al-Shaer, E. (2018), "Dynamic identification of axial force and boundary restraints in tie rods and cables with uncertainty quantification using Set Inversion Via Interval Analysis", J. Sound Vib., 423, 401-420. https://doi.org/10.1016/j.jsv.2018.02.062
  27. Kim, J.T., Yun, C.B., Ryu, Y.S. and Cho, H.M. (2004), "Identification of prestress-loss in PSC beams using modal information", Struct. Eng. Mech., 17(3-4), 467-482. https://doi.org/10.12989/sem.2004.17.3_4.467
  28. Law, S.S. and Lu, Z.R. (2005), "Time domain responses of a pre-stressed beam and pre-stress identification", J. Sound Vib., 288(4-5), 1011-1025. https://doi.org/10.1016/j.jsv.2005.01.045.
  29. Limongelli, M.P., Siegert, D., Merliot, E., Waeytens, J., Bourquin, F., Vidal, R., Le Corvec, V., Gueguen, I. and Cottineau, L.M. (2016), "Damage detection in a post tensioned concrete beam - Experimental investigation", Eng. Struct., 128, 15-25. https://doi.org/10.1016/j.engstruct.2016.09.017.
  30. Liu, T.K. and Chern, J.C. (2018), "Establishment of B4-TW prediction model for concrete deformation in Taiwan (I): basic creep, drying creep and total creep", Struct. Eng., 33(3), 43-64 (in Chinese).
  31. Lu, Z.R. and Law, S.S. (2006), "Identification of pre-stress force from measured structural responses", Mech. Syst. Signal Process., 20(8), 2186-2199. https://doi.org/10.1016/j.ymssp.2005.09.001.
  32. MATLAB (2019), MATLAB documentation, Introduction to GUIDE, The Mathworks, Inc., 2019a, http://www.mathworks.com/help/matlab/creating_guis/introduction-to-guide.html.
  33. Mehta, P.K. and Monteiro, P.J.M. (2006), Concrete: Microstructure, Properties, and Materials, 3rd Edition, McGraw-Hill, New York, USA.
  34. Miyamoto, A., Tei, K., Nakamura, H. and Bull, J.W. (2000), "Behavior of pre-stressed beam strengthened with external tendons", J. Struct. Eng., 126(9), 1033-1044. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:9(1033).
  35. Muller, H.S. and Hilsdorf, H.K. (1990), General Task Group 9, CEB Comite Euro-International du Beton, Paris, France, 201.
  36. Noble, D., Nogal, M., O'Connor, A. and Pakrashi, V. (2015), "Dynamic impact testing on post-tensioned steel rectangular hollow sections; An investigation into the 'compression-softening' effect", J. Sound Vib., 355, 246-263. https://doi.org/10.1016/j.jsv.2015.06.021
  37. Noble, D., Nogal, M., O'Connor, A. and Pakrashi, V. (2016), "The effect of prestress force magnitude and eccentricity on the natural bending frequencies of uncracked prestressed concrete beams", J. Sound Vib., 365, 22-44. https://doi.org/10.1016/j.jsv.2015.11.047.
  38. Ortega, N.F., Moro, J.M. and Meneses, R.S. (2018), "Theoretical model to determine bond loss in prestressed concrete with reinforcement corrosion", Struct. Eng. Mech., 65(1), 1-7. https://doi.org/10.12989/sem.2018.65.1.001.
  39. Palanisamy, S.P., Maheswaran, G., Annaamalai, M.G.L. and Vennila, P. (2015), "Steel slag to improve the high strength of concrete", Int. J. Chemtech Res., 7(5), 2499-2505.
  40. Rebecchi, G., Tullini, N. and Laudiero, F. (2013), "Estimate of the axial force in slender beams with unknown boundary conditions using one flexural mode shape", J. Sound Vib., 332(18), 4122-4135. https://doi.org/10.1016/j.jsv.2013.03.018.
  41. Saiidi, M., Douglas, B. and Feng, S. (1994), "Prestress force effect on vibration frequency of concrete bridges", J. Struct. Eng., 120(7), 2233-2241. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:7(2233).
  42. Singh, B.P., Yazdani, N. and Ramirez, G. (2013), "Effect of a time dependent concrete modulus of elasticity on prestress losses in bridge girders", Int. J. Concr. Struct. Mater., 7(3), 183-191. https://doi.org/10.1007/s40069-013-0037-0.
  43. Song, Y. (2000), Dynamics of Highway Bridges, Beijing: China Communications Press, China, Chapter 1, 113-120 (in Chinese).
  44. STRAUS7 (2004), Release 2.3.3. G+D Computing Pty Ltd, Copyright.
  45. Timoshenko, S.P. and Gere, J.M. (1961), Theory of Elastic Stability, McGraw-Hill, New York, USA.
  46. Toyota, Y., Hirose, T., Ono, S. and Shidara, K. (2017), "Experimental study on vibration characteristics of prestressed concrete beam", Procedia Eng., 171, 1165-1172. https://doi.org/10.1016/j.proeng.2017.01.483.
  47. Tullini, N. and Laudiero, F. (2008), "Dynamic identification of beam axial loads using one flexural mode shape", J. Sound Vib., 318(1-2), 131-147. https://doi.org/10.1016/j.jsv.2008.03.061.
  48. Tullini, N., Rebecchi, G. and Laudiero, F. (2012), "Bending tests to estimate the axial force in tie-rods", Mech. Res. Commun., 44, 57-64. https://doi.org/10.1016/j.mechrescom.2012.06.005.
  49. Tullini, N. (2013), "Bending tests to estimate the axial force in slender beams with unknown boundary conditions", Mech. Res. Commun., 53, 15-23. https://doi.org/10.1016/j.mechrescom.2013.07.011.
  50. Tullini, N., Rebecchi, G. and Laudiero, F. (2019), "Reliability of the tensile force identification in ancient tie-rods using one flexural mode shape", Int. J. Archit. Herit., 13(3), 402-410. https://doi.org/10.1080/15583058.2018.1563227.
  51. Wang, T.H., Huang, R. and Wang, T.W. (2013), "The variation of flexural rigidity for post-tensioned prestressed concrete beams", J. Mar. Sci. Technol., 21(3), 300-308. https://doi.org/10.6119/JMST-012-0508-2
  52. Young, W.C. and Budynas, R.G. (2002), Roark's Formulas for Stress and Strain, McGraw-Hill, Chapter 16, 767-768.
  53. Zhang, Y. and Li, R. (2007), "Natural frequency of full-prestressed concrete beam", Transactions Tianjin Univ., 13(5), 354-359.

피인용 문헌

  1. Effect Steel Fibre Content on the Load-Carrying Capacity of Fibre-Reinforced Concrete Expansion Anchor vol.14, pp.24, 2021, https://doi.org/10.3390/ma14247757