Advances in aircraft and spacecraft science

  • 제8권4호
  • /
  • Pages.289-302
  • /
  • 2021
  • /
  • 2287-528X(pISSN)
  • /
  • 2287-5271(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Lifetime prediction of bearings in on-board starter generator

  • 투고 : 2021.02.05
  • 심사 : 2021.04.02
  • 발행 : 2021.07.25
⟨ 이전 논문 다음 논문 ⟩

초록

Ensuring flight safety for passengers as well as crew is the most important aspect of modern aviation, and in order to achieve this, it is necessary to be able to forecast the durability of individual components. The present contribution illustrates the results of a computational analysis to determine the possibility of analysing the prediction of bearing durability in on-board rotating equipment from the point of view of thermal fatigue.In this study, a method developed at the Air Force Institute of Technology was used for analysis, which allowed to determine the bearing durability from the flight altitude profile. Two aircraft have been chosen for analysis - a military M-28 and a civilian Embraer. As a result of the analysis were obtained: the bearing durability in on-board rotating devices, average operation time between failures, as well as failure rate. In conclusion, the practical applicability of this approach is demonstrated by the fact that even with a limited number of flight parameters, it is possible to estimate bearing durability and increase flight safety by regular inspections.

키워드

참고문헌

  1. AN (2020), M-28 B - Bryza z Mielca na lotnisku; Interia, Warsaw, Poland. https://www.interia.pl/t.
  2. Ashrafifar, A. and Jegarkandi, M.F. (2020), "Fin failure diagnosis for non-linear supersonic air vehicle based on inertial sensors", Adv. Aircr. Spacecr. Sci., 7(1), 1-17, http://doi.org/10.12989/aas.2020.7.1.001.
  3. Baum, C., Hetzler, H., Schroeders, S., Leister, T. and Seemann, W. (2021), "A computationally efficient nonlinear foil air bearing model for fully coupled, transient rotor dynamic investigations", Tribol. Int., 153, 106434. https://doi.org/10.1016/j.triboint.2020.106434.
  4. Brossier, P., Niel, D., Changenet, C., Ville, F. and Belmonte, J. (2020), "Experimental and numerical investigations on rolling element bearing thermal behaviour", Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 235(4), 842-853. https://doi.org/10.1177/1350650120932335.
  5. Brushan, B. (2013). Introduction To Tribology, John Wiley & Sons, New York, U.S.A.
  6. Cao, H., Niu, L., Xi, S. and Chen, X. (2018), "Mechanical model development of rolling bearing-rotor systems: A review", Mech. Syst. Signal Pr., 102, 37-58. https://doi.org/10.1016/j.ymssp.2017.09.023.
  7. Carrera, E. (2002), "Temperature profile influence on layered plates response considering classical and advanced theories", AIAA J., 40(9), 1885-1896. https://doi.org/10.2514/2.1868.
  8. Cinefra, M., Valvano, S. and Carrera E. (2015), "Heat conduction and Thermal Stress Analysis of laminated composites by a variable kinematic MITC9 shell element", Curved Layered Struct., 2(1), 301-320. https://doi.org/10.1515/cls-2015-0017.
  9. Dulci, K.B., Onel, Y.D., and Senol, I. (2006), "Detection of bearing defects in three-phase induction motors using Park's transform and radial basis function neural networks", Sadhana, 31(6), 235-244. https://doi.org/10.1007/BF02703379.
  10. Dabrowski, T. (1977), "Aeronautical Electrical Equipment, vol.3 Aircraft On-board Generators", WAT, Warsaw, Ploand.
  11. Farmakopoulos, M., Thanou, M., Nikolakopoulos, P., Papadopoulos, C. and Tzes , A. (2013), "Control model of active magnetic bearings", Proceedings of the 3rd International Conference of Engineering Against Failure (ICEAF III), Kos, Greece, June.
  12. Gloeckner, P. and Rodway, C. (2017),"The evolution of reliability and efficiency of aerospace bearing systems", Engineering, 9(11), 962-991. http://doi.org/10.4236/eng.2017.911058.
  13. Hoffmann, G.M., Waslander, S.L. and Tomlin, C.J. (2006), "Mutual information methods with particle filters for mobile sensor network control", Proceedings of the 45th Ieee Conference on Decision and Control, San Diego, USA, December.
  14. Inamura, S., Sakai, T. and Koich, S. (2003), "A temperature rise analysis of switched reluctance motor due to the core and copper loss by FEM", IEEE T. Magn., 39(3), 1554-1557. https://doi.org/10.1109/TMAG.2003.810358.
  15. ISO 15243 (2017), Rolling bearings - Damage and failures - Terms, characteristics and causes, International Organization for Standardization; Geneve, Swiss
  16. Jakupovic, A., Pavlic, M., Mestrovic, A. and Jovanovic, V. (2013), "Comparison of the Nodes of Knowledge method with other graphical methods for knowledge representation", Proceedings of 36th International Convention on Information and Communication Technology, Electronics and Microelectronics (MIPRO), Opatija, Croatia, May.
  17. LOT (2020), Embraer 175; LOT, Warsaw, Poland. https://www.lot.com/pl/pl.
  18. Mielec (2001), Technical description of the aeroplane BRYZA, Part 1 - Fuselage, Polskie Zaklady Lotnicze Mielec, Mielec, Poland.
  19. MIL-HDBK-217F (1991), Military Handbook, Reliability Prediction of Electronic Equipmen, Department of Defense, USA.
  20. Pandey, K., Zope, P. and Suralkar, S. (2012), "Review of fault diagnosis in three-phase induction motor. IJCA", Proceedings of the International Journal of Computer Applications (IJCA), Yavatmal, India, September.
  21. Patra, P., Kumar, D., Nowicki, D. and Randall, W. (2019), "Effective management of performance-based contracts for sustainment dominant systems", Int. J. Prod. Econom., 208, 369-382. https://doi.org/10.1016/j.ijpe.2018.11.025.
  22. Pontecorvo, M.E., Barbarino, S., Gandhi, F.S., Bland, S., Snyder, R., Kudva, J. and White, E.V. (2015), "A load-bearing structural element with energy dissipation capability under harmonic excitation", Adv. Aircr. Spacecr. Sci., 2(3), 345-365. http://doi.org/10.12989/aas.2015.2.3.345.
  23. Sharanya, S., Venkataraman, R. and Murali, G. (2020), "Analysis of machine learning based fault diagnosis approaches in mechanical and electrical components", Int. J. Adv. Res. Eng. Tech., 11(10), 80-94. http://doi.org/10.34218/IJARET.11.10.2020.008.
  24. Singh, S. and Vishwakarma, M. (2015), "A review of vibration analysis techniques for rotating machines", Int. J. Adv. Res. Eng. Tech., 4(3), 757-761. http://doi.org/10.17577/IJERTV4IS030823.
  25. Smith, M., Byington, C., Watson, M., Bharadwaj, S., Swerdon, G., Goebel, K. and Balaban, E. (2009), "Experimental and analytical development of health management for electro-mechanical actuators", Proceedings of the IEEE Aerospace Conference, Montana, USA, March. https://doi.org/10.1109/AERO.2009.4839660.
  26. Swaminathan, K. and Sangeetha D.M. (2017), "Thermal analysis of FGM plates-A critical review of various modeling techniques and solution methods", Compos. Struct., 160, 43-60. https://doi.org/10.1016/j.compstruct.2016.10.047
  27. Urban, R. and Hoskova-Mayerova, S. (2017), "Threat life cycle and its dynamics", Deturope, 9(2), 93-109. https://doi.org/10.32725/det.2017.014
  28. Wang, B., Lei, Y., Li, N. and Li, N. (2020a), "A hybrid prognostics approach for estimating remaining useful life of rolling element bearings", IEEE T. Reliab., 69(1), 401-412. http://doi.org/10.1109/TR.2018.2882682.
  29. Wang, Y., Cao, J., Tong, Q., An, G., Liu, R., Zhang, Y. and Yan, H. (2020b), "Study on the thermal performance and temperature distribution of Ball bearings in the traction motor of a high-speed EMU", Appl. Sci., 10(12), 1-14. https://doi.org/10.3390/app10124373.
  30. Wilson, D. and Smith, R. (1977), Electric motor reliability model, Shaker Research Corp., Ballston Lake, New York, USA.
  31. Yu, G. (2015), "Fault feature extraction using independent component analysis with reference and its application on fault diagnosis of rotating machinery", Neural Comput. Appl., 26, 187-198. https://doi.org/10.1007/s00521-014-1726-6.
  32. Zaghari, B., Weddell, A., Esmaeili, K., Bashir, I., Harvey, T., White, N. and Wang, L. (2020), "High-temperature self-powered sensing system for a smart bearing in an aircraft jet engine", IEEE T. Instrum. Meas., 69(9), 6165-6174. https://doi.org/10.1109/TIM.2020.2971288.
  33. Zhang, D., Han, X., Newaz, G., Favro, L. and Thomas, R. (2012), "Modelling turbine blade crack detection in sonic IR imaging with a method of creating flat crack surface in finite element analysis", Proceedings of AIP Conference, 1430(1), 527-532. https://doi.org/10.1063/1.4716272.