Advances in concrete construction

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Properties and durability of concrete with olive waste ash as a partial cement replacement

  • Tayeh, Bassam A. (Civil Engineering Department, Faculty of Engineering, Islamic University of Gaza) ;
  • Hadzima-Nyarko, Marijana (Faculty of Civil Engineering and Architecture Osijek, Josip Juraj Strossmayer University of Osijek) ;
  • Zeyad, Abdullah M. (Civil Engineering Department, College of Engineering, Jazan University) ;
  • Al-Harazin, Samer Z. (Civil Engineering Department, Faculty of Engineering, Islamic University of Gaza)
  • Received : 2020.08.21
  • Accepted : 2020.12.16
  • Published : 2021.01.25
⟨ Previous Next ⟩

Abstract

This research aims to study the utilization of olive waste ash (OWA) in the production of concrete as a partial substitute for cement. Effects of using OWA on the physical and mechanical properties of concrete mixtures have been investigated. This is done by carrying out tests involving the addition of various percentages of OWA to cement (0%, 5%, 10% and 15%). For each percentage, tests were performed on both fresh and hardened concrete; these included slump test, unit weight test and compressive strength test after 7, 28 and 90 days. Durability tests were investigated in solutions containing 5% NaOH and MgSO4 by weight of water. In addition, resistance to high temperatures was tested by subjecting the cubes to high temperatures of up to 170℃. The results of this research indicate that a higher percentage of OWA gives a lower compressive strength and lower workability but higher performance in terms of durability against both different weather conditions and high temperatures.

Keywords

References

  1. Abed, M., Nemes, R. and Tayeh, B.A. (2020), "Properties of selfcompacting high-strength concrete containing multiple use of recycled aggregate", J. King Saud Univ. Eng. Sci., 32(2), 108. https://doi.org/10.1016/j.jksues.2018.12.002.
  2. Adwan, O.K. and Maraqa, F.R. (2019), "Utilisation of olive mill waste and coal ashes in normal concrete mixes", Asian J. Sci. Technol., 10(1), 9348-9352.
  3. Agwa, I.S., Omar, O.M., Tayeh, B.A. and Abdelsalam, B.A. (2020), "Effects of using rice straw and cotton stalk ashes on the properties of lightweight self-compacting concrete", Constr. Build. Mater., 235, 117541. https://doi.org/10.1016/j.conbuildmat.2019.117541.
  4. Al-Akhras, N. (2012), "Performance of olive waste ash concrete exposed to alkali-silica reaction", Struct. Concrete, 13(4), 221-226. https://doi.org/10.1002/suco.201100058.
  5. Al-Akhras, N., Al-Akhras, K. and Attom, M. (2009), "Performance of olive waste ash concrete exposed to elevated temperatures", Fire Saf. J., 44, 370-375. https://doi.org/10.1016/j.firesaf.2008.08.006
  6. Al-Akhras, N.M. and Abdulwahid, M.Y. (2010), "Utilisation of olive waste ash in mortar mixes", Struct. Concrete, 11(4), 221-228. https://doi.org/10.1680/stco.2010.11.4.221.
  7. Al Saffar, D.M., Al Saad, A.J. and Tayeh, B.A. (2019), "Effect of internal curing on behavior of high performance concrete: An overview", Case Stud. Constr. Mater., 10, e00229. https://doi.org/10.1016/j.cscm.2019.e00229
  8. Alkheder, S., Obaidat, Y.T. and Taamneh, M. (2016), "Effect of olive waste (Husk) on behavior of cement paste", Case Stud. Constr. Mater., 5, 19-25. https://doi.org/10.1016/j.cscm.2016.05.001.
  9. Annadurai, S., Rathinam, K. and Kanagarajan, V. (2020), "Development of eco-friendly concrete produced with Rice Husk Ash (RHA) based geopolymer", Adv. Concrete Constr., 9(2), 139-147. https://doi.org/10.12989/acc.2020.9.2.139.
  10. Ashok, M., Jayabalan, P., Saraswathy, V. and Muralidharan, S. (2020), "A study on mechanical properties of concrete including activated recycled plastic waste", Adv. Concrete Constr., 9(2), 207-215. https://doi.org/10.12989/acc.2020.9.2.207.
  11. ASTM C143/C143M-15a (2015), Standard Test Method for Slump of Hydraulic-Cement Concrete, ASTM International, West Conshohocken, PA.
  12. ASTM C642-13 (2013), Standard Test Method for Density, Absorption, and Voids in Hardened Concrete, ASTM International, West Conshohocken, PA.
  13. Bahoria, B.V., Parbat, D.K. and Naganaik, P.B. (2013), "Replacement of natural sand in concrete by waste products: A state of art", J. Envir. Res. Develop., 7(4), 1651.
  14. Barthel, M., Rübner, K. and Kühne, H. (20166), "From waste materials to products for use in the cement industry", Adv. Cement Res., 28(7), 458-468. https://doi.org/10.1680/jadcr.15.00149.
  15. Beltran, M.G., Agrela, F., Barbudo, A., Ayuso, J. and Ramirez, A. (2014), "Mechanical and durability properties of concretes manufactured with biomass bottom ash and recycled coarse aggregates", Constr. Build. Mater., 72, 231-238. https://doi.org/10.1016/j.conbuildmat.2014.09.019.
  16. Binici, H. and Aksogan, O. (2016), "Eco-friendly insulation material production with waste olive seeds, ground PVC and wood chips", J. Build. Eng., 5, 260-266. https://doi.org/10.1016/j.jobe.2016.01.008.
  17. Borja, R., Raposo, F. and Rincon, B. (2006), "Treatment technologies of liquid and solid wastes from two-phase olive oil mills", Grasas Aceites, 57, 32-46.
  18. BS 1881 (1983), Method for Determination of Compressive Strength of Concrete Cubes, Part116, British Standards Institution, London.
  19. Cheraghalizadeh, R. and Akcaoglu, T. (2019), "Utilization of olive waste ash and sea sand powder in self‑compacting concrete", Iran. J. Sci. Technol., Tran. Civil Eng., 43, 663-672. https://doi.org /10.1007/s40996-018-0224-y.
  20. Cruz-Yusta, M., Marmol, I., Morales, J. and Sanchez, L. (2011), "Use of olive biomass fly ash in the preparation of environmentally friendly mortars", Environ. Sci. Tech., 45(16), 6991-6996. https://doi.org /10.1021/es200968a.
  21. Cuenca, J., Rodriguez, J., Martin-Morales, M., Sanchez-Roldan, Z. and Zamorano, M. (2013), "Effects of olive residue biomass fly ash as filler in self-compacting concrete", Constr. Build. Mater., 40, 702-709. https://doi.org/10.1016/j.conbuildmat.2012.09.101.
  22. De Belie, N. (2007), "Evaluation of methods for testing concrete degradation in aggressive solutions", Ed. De Belie, N., Workshop on Performance of Cement-based Materials in Aggressive Aqueous Environments-Characterization, Modelling, Test Methods and Engineering Aspects, Ghent, 63-74.
  23. De Belie, N., Monteny, J., Beeldens, A., Vincke, E., Van Gemert, D. and Vertraete, W. (2004), "Experimental research and prediction of the effect of chemical and biogenic sulfuric acid of different types of commercially produced concrete sewer pipes", Cement Concrete Res., 34(12), 2223-2236. https://doi.org/10.1016/j.cemconres.2004.02.015.
  24. DellaGreca, M., Monaco, P., Pinto, G., Pollio, A., Previtera, L. and Temussi, F. (2001), "Phytotoxicity of low-molecular-weight phenols from olive mill waste waters", Bull. Environ. Contamin. Toxicol., 67, 352-359. https://doi.org/10.1007/s001280132
  25. Eisa, A. (2014), "Properties of concrete incorporating recycled post-consumer environmental wastes", Int. J. Concrete Struct. Mater., 8(3), 251-258. https://doi.org/10.1007/s40069-013-0065-9.
  26. Eliche-Quesada, D. and Leite-Costa, J. (2016), "Use of bottom ash from olive pomace combustion in the production of eco-friendly fired clay bricks", Waste Manage., 48, 323-333. https://doi.org/10.1016/j.wasman.2015.11.042.
  27. Gartner, E. (2004), "Industrially interesting approaches to "low-CO2" cements", Cement Concrete Res., 34(9), 1489-1498. https://doi.org/10.1016/j.cemconres.2004.01.021.
  28. Hadzima-Nyarko, M., Nyarko, E.K., Ademovic, N., Milicevic, I. and Kalman Sipos, T. (2019), "Modelling the influence of waste rubber on compressive strength of concrete by artificial neural networks", Mater., 12, 561. https://doi.org/10.3390/ma12040561.
  29. Hilal, N., Ali, T.K.M. and Tayeh, B.A. (2020), "Properties of environmental concrete that contains crushed walnut shell as partial replacement for aggregates", Arab. J. Geosci., 13(16), 1-9. https://doi.org/10.1007/s12517-020-05733-9.
  30. Hosseini, S.A. (2020), "Application of various types of recycled waste materials in concrete constructions", Adv. Concrete Constr., 9(5), 479-489. https://doi.org/10.12989/acc.2020.9.5.479.
  31. International Olive Council (2020), Production Mondiale d'Huile d'Olive.
  32. Kamini, N.R., Edwinoliver, N.G., Thirunavukarasu, K., Gowthaman, M.K. and Rose, C. (2009), "Utilization of olive oil and its by-products for industrial applications", Olive Oil Health. 5.
  33. Mehta, P.K. (1975), "Evaluation of sulfate-resisting cements by a new test method", J. Am. Concrete Inst., 72(10), 573-575.
  34. Menendez, E., Matschei, T. and Glasser, F.P. (2013), "Sulphate attack of concrete", Performance of Cement-Based Materials in Aggressive Aqueous Environments, 1st Edition, Eds. Mark, A., Bertron, A., De Belie, N., 10, 7-78. https://doi.org /10.1007/978-94-007-5413-3.
  35. Mian, A., Bendig, M., Piazzesi, G., Manente, G., Lazzaretto, A. and Marechala, F. (2013), "Energy integration in the cement industry", Proceedings of the 23rd European Symposium on Computer Aided Process Engineering.
  36. Mo, K.H., Alengaram, U.J., Jumaat, M.Z., Yap, S.P. and Lee, S.C. (2016), "Green concrete partially comprised of farming waste residues: a review", J. Clean. Prod., 117, 122-138. https://doi.org/10.1016/j.jclepro.2016.01.022.
  37. Montane, D., Salvado, J., Torras, C. and Farriol, X. (2002), "High-temperature dilute-acid hydrolysis of olive stones for furfural production", Biomass Bioenergy, 22, 295-304. https://doi.org/10.1016/S0961-9534(02)00007-7.
  38. Mori, T., Nonaka, T., Tazaki, K., Koga, M., Hikosaka, Y. and Noda, S. (1992), "Interactions of nutrients, moisture and pH on microbial corrosion of concrete sewer pipes", Water Res., 26(1), 29-37. https://doi.org/10.1016/0043-1354(92)90107-F.
  39. Moriconi, G. (2007), "Recyclable Materials in concrete technology: sustainability and durability, Sustainable Construction Materials and Technologies", Proceedings of the Special Sessions of First inter. conference on sustainable construction materials and technologies, Coventry, UK.
  40. National Ready Mixed Concrete Association (2008), Concrete CO2 Fact Sheet, NRMCA Publication Number 2.
  41. Panda, K.C. and Prusty, S.D. (2015), "Influence of silpozz and rice husk ash on enhancement of concrete strength", Adv. Concrete Constr., 3(3), 203-221. http://dx.doi.org/10.12989/acc.2015.3.3.203.
  42. Paredes, M.J., Moreno, E., Ramoscormenzana, A. and Martinez, J. (1987), "Characteristics of soil after pollution with waste-waters from olive oil extraction plants", Chemosph., 16, 1557-1564. https://doi.org/10.1016/0045-6535(87)90096-8
  43. Rajamma, R., Ball, R., Tarelho, L., Allen, G., Labrincha, J. and Ferreira, V. (2009), "Characterization and use of biomass fly ash in cement-based materials", J. Hazard. Mater., 172(2-3), 1049-1060. https://doi.org/10.1016/j.jhazmat.2009.07.109.
  44. Ren, R., Liang, J.F., Liu, D., Gao, J. and Chen, L. (2020), "Mechanical behavior of crumb rubber concrete under axial compression", Adv. Concrete Constr., 9(3), 249-256. https://doi.org/10.12989/acc.2020.9.3.249.
  45. Richardson, E.A. and Fuller, T. (2013), "Sea shells used as partial aggregate replacement in concrete", Struct. Survey, 31(5), 347-354. https://doi.org/10.1108/SS-12-2012-0041.
  46. Rosales, J., Beltran, M.G., Cabrera, M., Velasco, A. and Agrela, F. (2016), "Feasible use of biomass bottom ash as addition in the manufacture of lightweight recycled concrete", Waste Biomass Valor., 7, 953-963. https://doi.org /10.1007/s12649-016-9522-4.
  47. Sand, W., Bock, E. and White, D.C. (1987), "Biotest system for rapid evaluation of concrete resistance to sulfur-oxidizing bacteria", Mater. Perform., 26(3), 14-17.
  48. Tayeh, B.A. (2018), "Effects of marble, timber, and glass powder as partial replacements for cement", J. Civil Eng. Constr., 7(2), 63-71. https://doi.org/10.32732/jcec.2018.7.2.63.
  49. Tayeh, B.A., Hasaniyah, M.W., Zeyad, A.M. and Yusuf, M.O. (2019), "Properties of concrete containing recycled seashells as cement partial replacement: A review", J. Clean. Prod., 237, 117723. https://doi.org/10.1016/j.jclepro.2019.117723.
  50. Tayeh, B.A., Hasaniyah, M.W., Zeyad, A.M., Awad, M.M., Alaskar, A., Mohamed, A.M. and Alyousef, R. (2020), "Durability and mechanical properties of seashell partiallyreplaced cement", J. Build. Eng., 20. 101328. https://doi.org/10.1016/j.jobe.2020.101328.
  51. Tsimidou, M. (1998), "Polyphenols and quality of virgin olive oil in retrospect", Ital. J. Food Sci., 10, 99-116.
  52. Van Tittelboom, K., De Belie, N. and Hooton, R.D. (2012), "Test methods for resistance of concrete to sulfate attack-A critical review performance of cement-based materials in aggressive aqueous environments", Performance of Cement-Based Materials in Aggressive Aqueous Environments, 1st Edition, Eds. Mark, A., Bertron, A., De Belie, N., Springer, Netherlands. 10, 251-288. https://doi.org /10.1007/978-94-007-5413-3_10.
  53. VijayaSekhar Reddy, M., Ramana Reddy, I.V., Madan Mohan Reddy, K. and Ravi Kumar, C.M. (2013), "Durability aspects of standard concrete", Int. J. Struct. Civil Eng. Res., 2, 40-46.
  54. Vincke, E., Verstichel, S., Monteny, J. andVerstraete, W. (1999), "A new test procedure for biogenic sulfuric acid corrosion of concrete", Biodegradat., 10(6), 421-428. https://doi.org/10.1023/A:1008309320957
  55. Yildirim, S.T. and Duygun, N.P. (2017), "Mechanical and physical performance of concrete including waste electrical cable rubber", IOP Conf. Ser.: Mater. Sci. Eng., 245, 022054 https://doi.org/10.1088/1757-899X/245/2/022054.
  56. Zeyad, A.M., Tayeh, B.A. and Yusuf, M.O. (2019), "Strength and transport characteristics of volcanic pumice powder based high strength concrete", Constr. Build. Mater., 216, 314-324. https://doi.org/10.1016/j.conbuildmat.2019.05.026.
  57. Zeyad, A.M., Tayeh, B.A., Saba, A.M. and Johari, M.A. (2018), "Workability, setting time and strength of high-strength concrete containing high volume of palm oil fuel ash", Open Civil Eng. J., 12(1), 35-46. https://doi.org/10.2174/1874149501812010035.