Advances in concrete construction

  • 제11권1호
  • /
  • Pages.45-58
  • /
  • 2021
  • /
  • 2287-5301(pISSN)
  • /
  • 2287-531X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Improving the flexural toughness behavior of R.C beams using micro/nano silica and steel fibers

  • Eisa, Ahmed S. (Structural Engineering Department, Zagazig University) ;
  • Shehab, Hamdy K. (Structural Engineering Department, Zagazig University) ;
  • El-Awady, Kareem A. (Structural Engineering Department, Zagazig University) ;
  • Nawar, Mahmoud T. (Structural Engineering Department, Zagazig University)
  • 투고 : 2020.09.08
  • 심사 : 2020.12.18
  • 발행 : 2021.01.25
⟨ 이전 논문 다음 논문 ⟩

초록

Experimental investigation has been conducted to study the effect of using Micro/Nano Silica in presence of steel fibers on improving the static response of reinforced concrete beams. Twenty-one mixtures were prepared with micro silica (MS), Nano silica (NS) and steel fibers (SFs) at different percentages. Cement was replaced by 10% and 15% of Micro silica and 1%, 2% and 3% of Nano silica in the presence of steel fibers at different volume fractions 0%, 1%, and 2%. 258 concrete samples, (126 cubes, 63 cylinders, 63 prisms, and six R.C beams), were investigated experimentally in two stages. The first stage was to investigate the mechanical properties of the prepared mixtures. The second stage was to study the static behavior of R.C beams, using the designed concrete mixtures, under a four-point flexural test. The results showed that replacing cement by (10% MS and 1% NS) produces the optimum mix with a significant improvement in the mechanical properties and the response of R.C beams under static loads. In addition, incorporating steel fibers at different volume fractions have a considerable effect on the flexural toughness of concrete mixes.

키워드

참고문헌

  1. ACI 318 (2018), Building Code Requirements for Structural Concrete and Commentary, American Concrete Institute. Farmington, Hills, USA.
  2. ACI Committee 544, 3R-08 (2008), Guide for Specifying, Proportioning, and Production of Fibre Reinforced Concrete, American Concrete Institute, Farmington, Hills, USA.
  3. Ahmadi, H., Kamran, M. and Tafaroj, N. (2011), "Lightweight nano concrete", J. Technol. Art. Constr. Eng. Organiz., Gilan Prov., 52, 8-13.
  4. Ajileye, F.V. (2012), "Investigations on microsilica (silica fume) as partial cement replacement in concrete", Global J. Res. Eng., 12(1-E).
  5. Al-Tayyib, A.J., Al-Zahrani, M.M. and Al-Sulaimani, G.J. (1988), "Effect of polypropylene fiber reinforcement on the properties of fresh and hardened concrete in the Arabian Gulf environment", Cement Concrete Res., 18(4), 561-570. https://doi.org/10.1016/0008-8846(88)90049-x.
  6. ASTM C494 (2004), Standard Specification for Chemical Admixtures for Concrete, American Society for Testing and Materials., Philadelphia.
  7. ASTM, A. (2017), C150/C150M-17, Standard Specification for Portland Cement. American Society for Testing and Materials: West Conshohocken, PA, USA.
  8. ASTM, C. (2003), 1240, Standard Specification for Use of Silica Fume as a Mineral Admixture in Hydraulic-Cement Concrete, Mortar, and Grout, American Society for Testing and Material.
  9. Barbhuiya, G.H., Moiz, M.A., Hasan, S.D. and Zaheer, M.M. (2020), "Effects of the nanosilica addition on cement concrete: A review", Mater. Today: Proc., 32, 560-566. https://doi.org/10.1016/j.matpr.2020.02.143.
  10. Bhagat, N.K. and Gahir, J.S. (2018), "Effect of micro-silica and nano-silica on mechanical properties of concrete", Int. J. Civil Eng. Technol., 9(8), 1-7.
  11. Biggs, J.M. (1964), Introduction to Structural Dynamics, McGraw-Hill, New York.
  12. BS-1881:116 (1983), Testing Concrete Part 116. Method for Determination of Compressive Strength of Concrete Cubes, British Standards Institution, London.
  13. BS-1881:117 (1983), Testing Concrete Part 117, Method for Determination of Tensile Splitting Strength, British Standards Institution, London.
  14. Di Maida, P., Radi, E., Sciancalepore, C. and Bondioli, F. (2015), "Pullout behavior of polypropylene macro-synthetic fibers treated with nano-silica", Constr. Build. Mater., 82, 39-44. https://doi.org/10.1016/j.conbuildmat.2015.02.047.
  15. Di Maida, P., Sciancalepore, C., Radi, E. and Bondioli, F. (2018), "Effects of nano-silica treatment on the flexural post cracking behaviour of polypropylene macro-synthetic fibre reinforced concrete", Mech. Res. Commun., 88, 12-18. https://doi.org/10.1016/j.mechrescom.2018.01.004.
  16. Duan, P., Shui, Z., Chen, W. and Shen, C. (2013), "Effects of metakaolin, silica fume and slag on pore structure, interfacial transition zone and compressive strength of concrete", Constr. Build. Mater., 44, 1-6. https://doi.org/10.1016/j.conbuildmat.2013.02.075.
  17. E.S.S. 1109 (2002), Concrete Aggregates from Natural Sources, Egyptian Organization for Standardization, Cairo, Egypt.
  18. ECP 203 (2007), The Egyptian Code for Design and Construction of Concrete Structures-Tests Guide, Cairo, Egypt.
  19. Eisa, A.S., Elshazli, M.T. and Nawar, M.T. (2020), "Experimental investigation on the effect of using crumb rubber and steel fibers on the structural behavior of reinforced concrete beams", Constr. Build. Mater., 252, 119078. https://doi.org/10.1016/j.conbuildmat.2020.119078.
  20. Fawzy, Y.A.E. and Metwally, K.A. (2017), "Impact of steel fiber or nano silica on properties of concrete containing various cement types", Life Sci. J., 14(12). https://doi.org/10.7537/marslsj141217.06.
  21. Frank, H.P. (1979), Fibre Cements and Fibre Concretes, John Wiley and Sons, Ltd., New York, USA.
  22. Ghazy, A., Bassuoni, M.T., Maguire, E. and O'Loan, M. (2016), "Properties of fiber-reinforced mortars incorporating nanosilica", Fiber., 4(1), 6. https://doi.org/10.3390/fib4010006.
  23. Gorgis, I.N., Hassan, M.S. and Abdulkareem, R.T. (2016), "Effect of steel fibers, polypropylene fibers and/or nanosilica on mechanical properties of self-consolidating concrete", Eng. Technol. J., 34, 527-538.
  24. Gupta, S. (2013), "Application of silica fume and nanosilica in cement and concrete-A review", J. Today. Idea. Tomorrow. Technol., 1(2), 85-98. https://doi.org/10.15415/jotitt.2013.12006.
  25. Hanumesh, B.M., Varun, B.K. and Harish, B.A. (2015), "The mechanical properties of concrete incorporating silica fume as partial replacement of cement", Int. J. Emerg. Technol. Adv. Eng., 5(9), 270.
  26. Hasan-Nattaj, F. and Nematzadeh, M. (2017), "The effect of fortaferro and steel fibers on mechanical properties of high-strength concrete with and without silica fume and nano-silica", Constr. Build. Mater., 137, 557-572. https://doi.org/10.1016/j.conbuildmat.2017.01.078.
  27. Ibrahim, K.I.M. (2017), "The effect of fibers type and content on Nano silica concrete Nsc", J. Mech. Civil Eng., 14(2), 27-34. https://doi.org/10.9790/1684-1402082734.
  28. Imam, A., Kumar, V. and Srivastava, V. (2018), "Review study towards effect of Silica Fume on the fresh and hardened properties of concrete", Adv. Concrete Constr., 6(2), 145. https://doi.org/10.12989/acc.2018.6.2.145.
  29. JCI‐SF4 (1984), Method of Tests for Flexural Strength and Flexural Toughness of Fiber Reinforced Concrete.
  30. Koksal, F., Altun, F., Yigit, I. and Sahin, Y. (2008), "Combined effect of silica fume and steel fiber on the mechanical properties of high strength concretes", Constr. Build. Mater., 22(8), 1874- 1880. https://doi.org/10.1016/j.conbuildmat.2007.04.017.
  31. Koksal, F., Ilki, A. and Tasdemir, M.A. (2013), "Optimum mix design of steel-fibre-reinforced concrete plates", Arab. J. Sci. Eng., 38(11), 2971-2983. https://doi.org/10.1007/s13369-012-0468-y.
  32. Kumar, R. and Dhaka, J. (2016), "Review paper on partial replacement of cement with silica fume and its effects on concrete properties", Int. J. Technol. Res. Eng., 4(1), 83-85.
  33. Li, L.G., Zheng, J.Y., Zhu, J. and Kwan, A.K.H. (2018), "Combined usage of micro-silica and nano-silica in concrete: SP demand, cementing efficiencies and synergistic effect", Constr. Build. Mater., 168, 622-632. https://doi.org/10.1016/j.conbuildmat.2018.02.181.
  34. Lone, S.S., Gupta, M. and Mehta, G. (2016), "Comparative study of Nano-silica induced mortar, concrete and self-compacting concrete-A review", Ind. J. Sci. Technol., 9(44), 1-7. https://doi.org/10.17485/ijst/2016/v9i44/105288.
  35. Maheswaran, S., Bhuvaneshwari, B., Palani, G.S., Nagesh, R. and Kalaiselvam, S. (2013), "An overview on the influence of nano silica in concrete and a research initiative", Res. J. Recent Sci., 2, 17-24.
  36. Mermerdas, K., Gesoglu, M., Güneyisi, E. and Ö zturan, T. (2012), "Strength development of concretes incorporated with metakaolin and different types of calcined kaolins", Constr. Build. Mater., 37, 766-774. https://doi.org/10.1016/j.conbuildmat.2012.07.077.
  37. Mohamed, A.M. (2016), "Influence of nano materials on flexural behavior and compressive strength of concrete", HBRC J., 12(2), 212-225. https://doi.org/10.1016/j.hbrcj.2014.11.006.
  38. Mondal, P., Shah, S.P., Marks, L.D. and Gaitero, J.J. (2010), "Comparative study of the effects of microsilica and nanosilica in concrete", Tran. Res. Record: J. Tran. Res. Board, 2141(1), 6-9. https://doi.org/10.3141/2141-02.
  39. Montgomery, J., Abu-Lebdeh, T.M., Hamoush, S.A. and Picornell, M. (2016), "Effect of Nano-silica on the compressive strength of harden cement paste at different stages of hydration", Am. J. Eng. Appl. Sci., 9, 166-177. https://doi.org/10.3844/ajeassp.2016.166.177.
  40. Murthy, A.R. and Ganesh, P. (2019), "Effect of steel fibres and Nano silica on fracture properties of medium strength concrete", Adv. Concrete Constr., 7(3), 143-150. https://doi.org/10.12989/acc.2019.7.3.143.
  41. Nasution, A., Imran, I. and Abdullah, M. (2015), "Improvement of concrete durability by Nano materials", Procedia Eng., 125, 608-612. https://doi.org/10.1016/j.proeng.2015.11.078.
  42. Patil, H.S., Dwivedi, A.K. and Chatterjee, A.M. (2017), "Optimize properties of concrete with silica fume", MAYFEB J. Mater. Sci., 2, 1-4.
  43. PCA, Supplementary Cementitious Materials, Design and Control of Concrete Mixtures - Chapter 4, 5th Edition, Portland Cement Association.
  44. Qing, Y., Zenan, Z., Deyu, K. and Rongshen, C. (2007), "Influence of nano-SiO2 addition on properties of hardened cement paste as compared with silica fume", Constr. Build. Mater., 21(3), 539-545. https://doi.org/10.1016/j.conbuildmat.2005.09.001.
  45. Ramadoss, P. and Nagamani, K. (2012), "Modeling for the evaluation of strength and toughness of high-performance fiber reinforced concrete", J. Eng. Sci. Technol., 7(3), 280-291.
  46. Samman, T., Wafa, F. and Radain, T. (1999), "Mechanical properties of normal and high-strength concrete with steel fibers", J. King Abdulaziz Univ.-Eng. Sci., 12(1), 87-104. https://doi.org/10.4197/eng.12-1.6.
  47. Serag, M.I., Yasien, A.M., El-Feky, M.S. and Elkady, H. (2017), "Effect of nano silica on concrete bond strength modes of failure", Int. J., 12(29), 2892-2899. https://doi.org/10.21660/2017.29.160412.
  48. Sharaky, I.A., Megahed, F.A., Seleem, M.H. and Badawy, A.M. (2019), "The influence of silica fume, nano silica and mixing method on the strength and durability of concrete", SN Appl. Sci., 1(6). https://doi.org/10.1007/s42452-019-0621-2.
  49. Sharma, R. and Bansal, P.P. (2019), "Efficacy of supplementary cementitious material and hybrid fiber to develop the ultra-high performance hybrid fiber reinforced concrete", Adv. Concrete Constr., 8(1), 21-31. https://doi.org/10.12989/acc.2019.8.1.021.
  50. Signorini, C., Sola, A., Malchiodi, B., Nobili, A. and Gatto, A. (2020), "Failure mechanism of silica coated polypropylene fibres for Fibre Reinforced Concrete (FRC)", Constr. Build. Mater., 236, 117549. https://doi.org/10.1016/j.conbuildmat.2019.117549.
  51. Tadayon, M.K.M., Sepehri, H. and Sepehri, M. (2010), "Influence of Nano-silica particles on mechanical properties and permeability of concrete", The 2nd International Conference on Sustainable Construction Materials and Technologies, 1-7.
  52. Taher, M.J., Hassan, M.S. and Al-azawi, Z.M. (2015), "Combined effect of silica fume and steel fiber on modulus of elasticity of high performance concrete", Eng. Technol. J., 33, 868-876.
  53. UFC (2008), Structures to Resist the Effects of Accidental Explosions, Unified Facilities Criteria 3-340-02, Army Corps of Engineers, Washington, D.C.
  54. Yadegran, I., Mahoutian, M., Shekarchi, M. and Libre, N.A. (2007), "Effect of polypropylene fibers on shrinkage of self-compacting concrete", Proceedings of the 5th International RILEM Symposium on Self Compacting Concrete, 707-713.