Geomechanics and Engineering

  • 제24권2호
  • /
  • Pages.179-191
  • /
  • 2021
  • /
  • 2005-307X(pISSN)
  • /
  • 2092-6219(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Failure characteristics and mechanical mechanism of study on red sandstone with combined defects

  • Chen, Bing (State Key Laboratory of Mining Disaster Prevention and Control Co-founded by Shandong Province and the Ministry of Science and Technology) ;
  • Xia, Zhiguo (State Key Laboratory of Mining Disaster Prevention and Control Co-founded by Shandong Province and the Ministry of Science and Technology) ;
  • Xu, Yadong (State Key Laboratory of Mining Disaster Prevention and Control Co-founded by Shandong Province and the Ministry of Science and Technology) ;
  • Liu, Shuai (College of Earth Resource Sciences and Engineering, North China University of Water Resources and Electric Power) ;
  • Liu, Xingzong (College of Civil Engineering, Lu Dong University)
  • 투고 : 2020.09.21
  • 심사 : 2021.01.08
  • 발행 : 2021.01.25
⟨ 이전 논문 다음 논문 ⟩

초록

In this study, the strength and failure mechanism of red sandstones with combined defects were investigated by uniaxial compression tests on red sandstones with different crack angles using two-dimensional particle flow code numerical software, and their mechanical parameters and failure process were studied and analyzed. The results showed that the mechanical characteristics such as peak strength, peak strain, and elastic modulus of the samples with prefabricated combined defects were significantly inferior than those of the intact samples. With increasing crack angle from 15° to 60°, the weakening area of cracks increased, elastic modulus, peak strength, and peak strain gradually reduced, the total number of cracks increased, and more strain energy was released. In addition, the samples underwent initial brittle failure to plastic failure stage, and the failure form was more significant, leading to peeling phenomenon. However, with increasing crack angle from 75° to 90°, the crack-hole combination shared the stress concentration at the tip of the crack-crack combination, resulted in a gradual increase in elastic modulus, peak strain and peak strength, but a decrease in the number of total cracks, the release of strain energy reduced, the plastic failure state weakened, and the spalling phenomenon slowed down. On this basis, the samples with 30° and 45° crack-crack combination were selected for further experimental investigation. Through comparative analysis between the experimental and simulation results, the failure strength and final failure mode with cracks propagation of samples were found to be relatively similar.

키워드

과제정보

This study was supported by "A Project of Shandong Province Higher Educational Science and Technology Program" (J13LG08).

참고문헌

  1. Afolagboye, L.O., He, J.M. and Wang, S.J. (2017), "Experimental study on cracking behaviour of moulded gypsum containing two non-parallel overlapping flaws under uniaxial compression", Acta Mech. Sinica, 33(2), 394-405. https://doi.org/10.1007/s10409-016-0624-9.
  2. Aharonov, E. and Karcz, Z. (2019), "How stylolite tips crack rocks", J. Struct. Geol., 118, 299-307. https://doi.org/10.1016/j.jsg.2018.11.002.
  3. Asadizadeh, M., Moosavi, M. and Hossaini, M.F. (2018), "Investigation of mechanical behaviour of non-persistent jointed blocks under uniaxial compression", Geomech. Eng., 14(1), 29-42. https://doi.org/10.12989/gae.2018.14.1.029.
  4. Bastola, S. and Cai, M. (2019), "Investigation of mechanical properties and crack propagation in pre-cracked marbles using lattice-spring-based synthetic rock mass (LS-SRM) modeling approach", Comput. Geotech., 110, 28-43. https://doi.org/10.1016/j.compgeo.2019.02.009.
  5. Bratov, V. and Krivtsov, A. (2019), "Analysis of energy required for initiation of inclined crack under uniaxial compression and mixed loading", Eng. Fract. Mech., 216, 106518. https://doi.org/10.1016/j.engfracmech.2019.106518.
  6. Chen, B, Zhang, S.C, Li, Y.Y, Li, Z.K and Zhou, H.J (2020), "Physical simulation study of crack propagation and instability information discrimination of rock-like materials with faults", Arab. J. Geosci., 13(18), 1-14. https://doi.org/10.1007/s12517-020-05966-8.
  7. Chen, S.J., Xia, Z.G. and Yin, D.W. (2020), "Numerical study on strength and failure characteristics of rock samples with different hole defects", B. Eng. Geol. Environ., 1-18. https://doi.org/10.1007/s12517-020-05966-8
  8. Cho, N, Martin, C.D and Sego, D.C. (2007), "A clumped particle model for rock", Int. J. Rock Mech. Min. Sci., 44(7), 997-1010. https://doi.org/10.1016/j.ijrmms.2007.02.002.
  9. Cundall, P.A. and Strack, O.D. (2008), "A discreate numerical model for granular assemblies", Geotechnique, 29(1), 47-65. https://doi.org/10.1680/geot.1980.30.3.331.
  10. Damaskinskaya, E.E., Hilarov, V.L., Panteleev, I.A., Gafurova, D.R. and Frolov, D.I (2018), "Statistical regularities of formation of a main crack in a structurally inhomogeneous material under various deformation conditions", Phys. Solid State, 60(9), 1821-1826. https://doi.org/10.1155/2018/7065029.
  11. Du, M.R, Jing, H.W., Su, H.J. and Zhu T.T. (2016), "Experimental study of strength and failure characteristics of sandstone containing prefabricated elliptical hole", J. China U. Min. Technol., 45(6), 1164-1171. https://doi.org/10.13247/j.cnki.jcumt.000593.
  12. Germanou, L., Ho, M.T. and Zhang, Y.H. (2018), "Intrinsic and apparent gas permeability of heterogeneous and anisotropic ultra-tight porous media", J. Nat. Gas Sci. Eng., 60, 271-283. https://doi.org/10.1016/j.jngse.2018.10.003.
  13. Gratchev, I., Dong, H.K. and Chong, K.Y. (2016), "Strength of rock-like specimens with preexisting cracks of different length and width", Rock Mech. Rock. Eng., 49(11), 4491-4496. https://doi.org/10.1007/s00603-016-1013-1.
  14. Haeri, H., Khaloo, A. and Marji, M.F. (2015), "Fracture analyses of different pre-holed concrete specimens under compression", Acta Mechanica Sinica, 31(6), 855-870. https://doi.org/10.1007/s10409-015-0436-3.
  15. Jessu, K.V. and Spearing, A.J.S. (2019), "Direct strain evaluation method for laboratory-based pillar performance", J. Rock Mech. Geotech. Eng., 11(4), 860-866. https://doi.org/10.1016/j.jrmge.2018.12.017.
  16. Katcoff, C.Z. and Graham-Brady, L.L. (2014), "Modeling dynamic brittle behavior of materials with circular flaws or pores", Int. J. Solids Struct., 51(3-4), 754-766. https://doi.org/10.1016/j.ijsolstr.2013.11.004.
  17. Lee, H.W. and Jeon, S. (2011), "An experimental and numerical study of fracture coalescence in pre-cracked specimens under uniaxial compression", Int. J. Solids Struct., 48(6), 979-999. https://doi.org/10.1016/j.ijsolstr.2010.12.001.
  18. Li, H.Q. and Wong, L.N.Y. (2013), "Numerical study on coalescence of pre-existing flaw pairs in rock-like material", Rock Mech. Rock Eng., 47(6),2087-2105. https://doi.org/10.1007/s00603-013-0504-6.
  19. Lisjak, A. and Grasselli, G. (2014), "A review of discrete modeling techniques for fracturing processes in discontinuous rock masses", J. Rock Mech. Geotech. Eng., 6(4), 301-314. https://doi.org/10.1016/j.jrmge.2013.12.007.
  20. Liu, T., Lin, B.Q. and Yang, W. (2017), "Mechanical behavior and failure mechanism of pre-cracked specimen under uniaxial compression", Tectonophysics, 712-713, 330-343. https://doi.org/10.1016/j.tecto.2017.06.004.
  21. Liu, W., Zhang J.P., Liu, L.M., Zhang F.T. and Mao, H.K. (2019), "Experimental study on freezing thermal parameters and uniaxial compression of weathered rock and soil in Yuandatan coal mine", J. Shandong U. Sci. Technol. Nat. Sci., 38(5), 31-38.
  22. Lv, Y.W., Sun, C.P. and Shen, B.T. (2019), "Experimental study on damage evolution and crack propagation characteristics of sandstone under combined stress state", J. Shandong U. Sci. Techno. (Nature Science), 39(1), 37-45.
  23. Ma, Q., Tan, Y., Liu, X., Gu, Q. and Li, X. (2020), "Effect of coal thicknesses on energy evolution characteristics of roof rock coal-floor rock sandwich composite structure and its damage constitutive model", Compos. Part B Eng., 198, 108086. https://doi.org/10.1016/j.compositesb.2020.108086.
  24. Mondal, S., Olsen-Kettle, L. and Gross, L. (2019), "Simulating damage evolution and fracture propagation in sandstone containing a preexisting 3-D surface flaw under uniaxial compression", Int. J. Numer. Anal. Met., 43(7), 1448-1466. https://doi.org/10.1002/nag.2908.
  25. Morgan, S.P. and Einstein, H.H. (2017), "Cracking processes affected by bedding planes in opalinus shale with flaw pairs", Eng. Fract. Mech., 176, 213-234. https://doi.org/10.1016/j.engfracmech.2017.03.003.
  26. Saadati, M., Forquin, P. Weddfelt, K. and Larsson, P.L. (2016), "On the tensile strength of granite at high strain rates considering the Iinfluence from preexisting cracks", Adv. Mater. Sci. Eng. https://doi.org/10.1155/2016/6279571.
  27. Sarfarazi, V., Haeri, H. and Shemirani, A.B. (2018), "Simulation of fracture mechanism of pre-holed concrete model under Brazilian test using PFC3D", Smart Struct. Syst., 22(6), 675-687. https://doi.org/10.12989/sss.2018.22.6.675.
  28. Shi, H., Song, L., Zhang H. Q., Xue, K.K., Yuan, G.T., Wang Z.S. and Wang, G.Z. (2019), "Numerical study on mechanical and failure properties of sandstone based on the power-law distribution of pre-crack length", Geomech. Eng., 19(5), 421-434. https://doi.org/10.12989/gae.2019.19.5.421.
  29. Vahab, S., Hadi, H. and Alireza, B.S. (2018), "Simulation of fracture mechanism of pre-holed concrete model under Brazilian test using PFC3D", Smart Struct. Syst., 22(6), 675-687. https://doi.org/10.12989/sss.2018.22.6.675.
  30. Wong, R.H. and Lin, P. (2015), "Numerical study of stress distribution and crack coalescence mechanisms of a solid containing multiple holes", Int. J. Rock Mech. Min. Sci., 79, 41-54. https://doi.org/10.1016/j.ijrmms.2015.08.003.
  31. Wong, R.H.C., Lin, P. and Tang, C.A. (2006), "Experimental and numerical study on splitting failure of brittle solids containing single pore under uniaxial compression", Mech. Mater., 38(1), 142-159. https://doi.org/10.1016/j.mechmat.2005.05.017.
  32. Xia, Z.G., Chen, S.J., Liu, X.Z. and Sun, R. (2020), "Strength characteristics and fracture evolution of rock with different shapes inclusions based on particle flow code", Geomech. Eng., 22(5), 461-473. https://doi.org/10.12989/gae.2020.22.5.461.
  33. Xu J., Haque A., Gong W., Gamage R.P. and Xu F. (2020), "Experimental study on the bearing mechanisms of rock-socketed piles in soft rock based on micro X-ray CT analysis", Rock Mech. Rock Eng., 53, 3395-3416. https://doi.org/10.1007/s00603-020-02121-3.
  34. Xu, Z.H., Wang, W.Y., Lin, P. and Xiong, Y. (2015), "A parameter calibration method for PFC simulation: Development and a case study of limestone", Geomech. Eng., 22(1), 97-108. https://doi.org/10.12989/gae.2020.22.1.097.
  35. Xue, D.J. (2020), "Determination of uniaxial compressive strength of intact rock", J. Shandong U. Sci. Technol. Nat. Sci., 39(4), 28-36.
  36. Yang, D.S., Jing, H.W., Li, Y.H. and Wang, S.Y. (2012), "An experimental study of the fracture coalescence behaviour of brittle sandstone specimens containing three fissures", Rock. Mech. Rock. Eng., 45(4), 563-582. https://doi.org/10.1007/s00603-011-0206-x.
  37. Yin, D.W., Chen S.J., Ge Y. and Liu R, (2021), "Mechanical properties of rock-coal bi-material samples with different lithologies under uniaxial loading", J. Mater. Res. Technol., 10, 322-338. https://doi.org/10.1016/j.jmrt.2020.12.010.
  38. Zaitsev, Y.B. and Wittmann, F.H. (1981), "Simulation of crack propagation and failure of concrete", Mater. Struct., 83(14), 357-365. https://doi.org/10.1007/BF02478729.
  39. Zhao J.H., Chen, J.T., Zhang, X.G., Jiang, N. and Zhang, Y.Z. (2020), "Distribution characteristics of floor pore water pressure based on similarity simulation experiments", B. Eng. Geol. Environ. https://doi.org/10.1007/s10064-020-01835-6.
  40. Zhu, Q.Q, Li, D.Y., Han, Z.Y., Li X.B. and Zhou, Z.L. (2019), "Mechanical properties and fracture evolution of sandstone specimens containing different inclusions under uniaxial compression", Int. J. Rock Mech. Min. Sci., 115, 33-47. https://doi.org/10.1016/j.ijrmms.2019.01.010.