드라이브 ㆍ 컨트롤 (Journal of Drive and Control)

  • 제18권4호
  • /
  • Pages.84-90
  • /
  • 2021
  • /
  • 2671-7972(pISSN)
  • /
  • 2671-7980(eISSN)
유공압건설기계학회 (The Korean Society for Fluid Power and Construction Equipment)
권호 표지
DOI QR코드

DOI QR Code

Optimum Hydraulic Oil Viscosity Based on Slipper Model Simulation for Swashplate Axial Piston Pumps/Motors

  • Kazama, Toshiharu (College of Design and Manufacturing Technology, Graduate School of Muroran Institute of Technology)
  • 투고 : 2021.11.25
  • 심사 : 2021.11.26
  • 발행 : 2021.12.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Viscosity of hydraulic oils decreases due to loss reduction and efficiency increase of fluid power systems. However, low viscosity is not always appropriate due to the induction of large leakage and small lubricity. Therefore, a detailed study on the optimum viscosity of hydraulic oils is necessary. In this study, based on the thermohydrodynamic lubrication theory, numerical simulation was conducted using the slipper model of swashplate-type axial piston pumps and motors. The viscosity grades' (VG) effects of oils on power losses are mainly discussed numerically in fluid film lubrication, including changes in temperature and viscosity. The simulation results reveal that the flow rate increases and the friction torque decreases as VG decreases. The film temperature and power loss were minimised for a specific oil with a VG. The minimum conditions regarding the temperature and loss were different and closed. Under various operating conditions, the film temperature and power loss were minimised, suggesting that an optimum hydraulic oil with a specific VG could be selected for given operating conditions of pressure and speed. Otherwise, a preferable operating condition must be established to determine a specific VG oil.

키워드

참고문헌

  1. H. E. Merritt, Hydraulic Control Systems, Wiley, 1967.
  2. T. Kazama, "Transmitted Power of Piping and Wiring in Hydraulic, Pneumatic, and Electric Drive Systems (Considerations for Loss in Pipes and Wires)," JFPS International Journal of Fluid Power System, Vol.13, No.2, pp.9-16, 2020. https://doi.org/10.5739/jfpsij.13.9
  3. T. Kazama, "A Comparative Newtonian and Thermal EHL Analysis Using Physical Lubricant Properties," Proc. of 28th Leeds-Lyon Symposium on Tribology, Wien, Austria, pp.435-446, 2002.
  4. T. Kazama, "Comparison of Power Density of Transmission Elements in Hydraulic, Pneumatic, and Electric Drive Systems," Mechanical Engineering Letters, Vol.5, pp.19-00139, 2019. https://doi.org/10.1299/mel.19-00139
  5. Japan Hydraulics and Pneumatics Society, Handbook of Hydraulics and Pneumatics (in Japanese), Ohm-sha, 1989.
  6. J. Koralewski, "Influence of Hydraulic Oil Viscosity on the Volumetric Losses in a Variable Capacity Piston Pump," Polish Maritime Research, Vol.18, No.3, pp. 55-65, 2011. https://doi.org/10.2478/v10012-011-0018-7
  7. A. Yamaguchi, "Motion of the Piston in Piston Pumps and Motors (Experiments and Theoretical Discussion)," JSME International Journal, Ser.B, Vol.37, No.1, pp.83-88, 1994. https://doi.org/10.1299/jsmeb.37.83
  8. K. Tanaka, S. Momozono, K. Kyogoku and Y. Fujita, "Effect of Geometric Shape of Piston on Power Loss of Sliding Part Between Piston and Cylinder in Swash Plate Type Piston Pump and Motor," Trans. of JSME (in Japanese), Vol.84, No.868, pp.18-00359, 2018.
  9. A. Yamaguchi and M. Tsuchimoto, "Bearing Seal Characteristics of the Oil Film Between a Valve Plate and a Cylinderblock of Axial Piston Pumps," Hydraulics and Pneumatics (in Japanese), Vol.13, No.1, pp.55-60, 1982. https://doi.org/10.5739/jfps1970.13.55
  10. M. Ivantysynova and J. Baker, "Power Loss in the Lubricating Gap Between Cylinder Block and Valve Plate of Swash Plate Type Axial Piston Machines," International Journal of Fluid Power, Vol.10, No.2, pp.29-43, 2009. https://doi.org/10.1080/14399776.2009.10780976
  11. N. Iboshi and A. Yamaguchi, "Characteristics of a Slipper Bearing for Swash Plate Type Axial Piston Pumps and Motors: 1st Report, Theoretical Analysis," Bulletin of JSME, Vol.25, No.210, pp.1921-1930, 1982. https://doi.org/10.1299/jsme1958.25.1921
  12. J. Chen, J. Ma, J. Li and Y. Fu, "Performance Optimization of Grooved Slippers for Aero Hydraulic Pumps," Chinese Journal of Aeronautics, Vol.29, No.3, pp.814-823, 2016. https://doi.org/10.1016/j.cja.2015.12.021
  13. M. M. Khonsari, "A Review of Thermal Effects in Hydrodynamic Bearings, Part I: Slider and Thrust Bearings," ASLE Transactions, Vol.30, No.1, pp.19-25, 1986. https://doi.org/10.1080/05698198708981725
  14. T. Kazama, "Thermohydrodynamic Lubrication Model Applicable to a Slipper of Swashplate Type Axial Piston Pumps and Motors (Effects of Operating Conditions)," Tribology Online, Vol.5, No.5, pp.250-254, 2010. https://doi.org/10.2474/trol.5.250
  15. T. Kazama, "Thermohydrodynamic Lubrication Model of a Slipper in Swashplate Type Axial Piston Machines-Validation Through Experimental Data," International Journal of Hydromechatronics, Vol.1, No.3, pp.259-271, 2018. https://doi.org/10.1504/ijhm.2018.094879
  16. T. Kazama, "Numerical Simulation of a Slipper Model with Multi-Lands and Grooves for Hydraulic Piston Pumps and Motors in Mixed Lubrication," Lubricants, Vol.7, No.7, pp.55, 2019. https://doi.org/10.3390/lubricants7070055
  17. T. Kazama, T. and A. Yamaguchi, "Optimum Design of Bearing and Seal Parts for Hydraulic Equipment," Wear, Vol.161, No.1/2, pp.161-171, 1993. https://doi.org/10.1016/0043-1648(93)90465-X
  18. T. Kazama, T. and A. Yamaguchi, "Application of a Mixed Lubrication Model for Hydrostatic Thrust Bearings of Hydraulic Equipment," J. of Tribology, Trans. of ASME, Vol.115, No.4, pp.686-691, 1993. https://doi.org/10.1115/1.2921694