Geomechanics and Engineering

  • 제27권5호
  • /
  • Pages.497-509
  • /
  • 2021
  • /
  • 2005-307X(pISSN)
  • /
  • 2092-6219(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Characteristic study of bell-shaped anchor installed within cohesive soil

  • Das, Arya (Department of Civil Engineering, Indian Institute of Engineering Science and Technology) ;
  • Bera, Ashis Kumar (Civil Engineering, Department of Civil Engineering, Indian Institute of Engineering Science and Technology)
  • 투고 : 2021.04.15
  • 심사 : 2021.11.11
  • 발행 : 2021.12.10
⟨ 이전 논문 다음 논문 ⟩

초록

A large deformation FEM (Finite Element Method) based numerical analysis has been performed to study the behaviour of the bell-shaped anchor embedded in undrained saturated (cohesive) soil with the help of finite element based software ABAQUS. A typical model anchor with bell-diameter of 0.125 m, embedded in undrained saturated soil with varying cohesive strength (from 5 kN/m2 to 200 kN/m2) has been chosen for studying the characteristic behaviour of the bell-shaped anchor installed in cohesive soil. Breakout factors have been evaluated for each case and verified with the results of experimental model tests for three different types of soil samples. The maximum value of breakout factor was found as about 8.5 within a range of critical embedment ratio of 2.5 to 3. An explicit model has been developed to estimate the breakout factor (Fc) for uplift capacity of bell-shaped anchor within clay mass in terms of H/D ratio (embedment ratio). It was also found that, the ultimate uplift capacity of the anchor increases with the increase of the value of cohesive strength of the soil and H/D ratio. The empirical equation developed in the present investigation is usable within the range of cohesion value and H/D ratio from 5 kN/m2 to 200 kN /m2 and 0.5 to 3.0 respectively. The proposed model has been validated against data obtained from a series of model tests carried out in the present investigation. From the stress-profile analysis of the soil mass surrounding the anchor, occurrence of stress concentration is found to be generated at the joint of anchor shaft and bell. It was also found that the vertical and horizontal stresses surrounding the anchor diminish at about a distance of 0.3 m and 0.15 m respectively.

키워드

참고문헌

  1. Adams, J.I. and Hayes, D.C. (1967), "The uplift capacity of shallow foundations", Ont. Hydro Res. Q., 19(1), 1-13.
  2. Ali, M. (1968), "Pullout resistance of anchor plates in soft bentonite clay", M.S. Dissertation, Duke University, Durham.
  3. Ardebili, Z.A., Gabr, M.A. and Rahman, S. (2016), "Uplift capacity of plate anchors in saturated clays: analyses with different constitutive models", J. Geomech., 16(2), 040150053: 1-11. 10.1061/(ASCE)GM.1943-5622.0000518.
  4. ASTM D2487 (2000), Classification of Soils for Engineering Purposes (Unified Soil Classification System), American Society of Testing Materials; Philadelphia, PA, USA.
  5. Balla, A. (1961), "The resistance to breaking out of mushroom foundations for pylons", Proceedings of 5th International Conference on Soil Mechanics and Foundation Engineering, 569-576, Paris, July.
  6. Banerjee, S. and Mahadevuni, N. (2017), "Pull-out behaviour of square anchor plates in reinforced soft clay", J. Geosynth. Ground Eng., 3(3), 1-10. https://doi.org/10.1007/s40891-017-0101-y
  7. Bowles, J.E. (2005), Foundation Analysis and Design, 5th Edition, The McGraw hill Company, Singapore.
  8. Bhattacharya, P. and Roy, A. (2016), "Improvement in uplift capacity of horizontal circular anchor plate in undrained clay by granular column", Geomech. Eng., 10(5), 617-633. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000639.
  9. Bhattacharya, P. (2017), "Pullout capacity of shallow inclined anchor in anisotropic and nonhomogeneous undrained clay", Geomech. Eng., 13(5), 825-844. http://dx.doi.org/10.12989/gae.2017.13.5.825.
  10. Chen, Z., Tho, K.K., Leung, C.F. and Chow, Y.K. (2013), "Influence of overburden pressure and soil rigidity on uplift behaviour of square plate anchor in uniform clay", Comput. Geotech., 52, 71-81. https://doi.org/10.1016/j.compgeo.2013.04.002
  11. Cheng, X., Yang, A. and Li, G. (2018), "Model tests and finite element analysis for the cyclic deformation process of suction anchors in soft clays", Ocean Eng, 151, 329-341. https://doi.org/10.1016/j.oceaneng. 2018.01.027.
  12. Das, B.M. (1978), "Model tests for uplift capacity of foundations in clay", Soils Foundations, 18(2), 17-24. https://doi.org/10.3208/sandf1972.18.2_17.
  13. Das, B. M. (1980), "A procedure for estimation of ultimate uplift capacity of foundation in clay", Soils Foundations, 20(1), 77-82. https://doi.org/10.3208/sandf1972.20.77.
  14. Das, B.M. and Singh, G. (1994), "Uplift capacity of plate anchors in clay", Proceedings of the FourthInternational Offshore and Polar Engineering Conference (EPC'94), ISOPE, Osaka, April.
  15. Deb, T. and Pal, S.K. (2018), "Study on the uplift behaviour and failure pattern of single belled anchor with 3D and 2D models in cohesionless soil bed", Iranian J. Sci. Technol. Trans. Civil Eng., 43(2), 327-343. https://doi.org/10.1007/s40996-018-0144-x.
  16. Degenkamp, G. and Dutta, A. (1989), "Soil resistances to embedded anchor chain in soft clay", J. Geotech. Eng., 115(10), 1420-1438. https://doi.org/10.1061/(ASCE)0733-9410(1989)115:10(1420).
  17. Han, C., Wang, D., Gaudin, C., Loughlin, C. and Cassidy, M.J. (2021), "Capacity of plate anchors in clay under sustained uplift", Ocean Eng., 226, 1-8. https://doi.org/10.1016/j.oceaneng.2021.108799.
  18. Khatri, V.N. and Kumar, J. (2009) "Vertical uplift resistance of circular plate anchors in clays under undrained condition", Comput. Geotech., 36(8), 1352-1359. https://doi.org/10.1016/j.compgeo.2009.06.008.
  19. Khatri, V.N. and Kumar, J. (2011), "Uplift capacity of axially loaded piles in clays", J. Geomech., 11(1), 23-28. https://doi.org/10.1016/j.compgeo.2009.06.008.
  20. Kupferman, M. (1971), "The vertical holding capacity of marine anchors in clay subjected to static and cyclic loading", M.S. Dissertation, University of Massachusetts, Amherst.
  21. Lai, Y., Zhu, B., Huang, Y. and Chen, C. (2020), "Behaviors of drag embedment anchor in layered clay profiles", Appl. Ocean Res., 101, 102287:1-13https://doi.org/10.1016/j.apor.2020.102287
  22. Liu, H., Su, F. and Li, Z. (2014), "The criterion for determining the ultimate pullout capacity of plate anchors in clay by numerical analysis", American J. Eng. Appl. Sci., 7(4), 374-386. https://doi.org/10.3844/ajeassp.2014.374.386.
  23. Mabsout, M.E., Reese, L.C. and Tassoulas, J.L. (1995), "Study of pile driving by finite element method", J. Geotech. Geoenviron. Eng., 121(7), 535-543. https://doi.org/10.1061/(ASCE)0733-9410(1995)121:7(535).
  24. Masouleh, S.F. andFakharian, K. (2007), "Application of a continuum numerical model for pile driving analysis and comparison with a real case", Comput. Geotech., 35(3), 406-418. https://doi.org/10.1016/j.compgeo.2007.08.009.
  25. Mabsout, M.E. and Tassoulas, J.L. (1994), "A finite element model for the simulation of pile driving", J. Numerical Methods Eng., 37(2), 257-278. https://doi.org/10.1002/nme.1620370206.
  26. Merifield, R.S., Sloan, S.W. and Yu, H.S. (2001), "Stability of plate anchors in undrained clay", Geotechnique, 51(2), 141-153. https://doi.org/10.1680/geot.2001.51.2.141.
  27. Merifield, R.S., Lyamin, A.V., Sloan, S.W. and Yu, H.S. (2003), "Three-dimensional lower bound solutions for stability of plate anchors in clay", J. Geotech. Geoenviron. Eng., 129(3), 243-253. https://doi.org/10.1061/(ASCE)1090-0241(2003)129:3(243).
  28. Merifield, R.S. and Smith, C.C. (2010), "The ultimate uplift capacity of multi-plate strip anchors in undrained clay", Comput. Geotech., 37(4), 504-514. https://doi.org/10.1016/j.compgeo.2010.02.004.
  29. Rao, A.S., Phanikumar, B.R., Babu, R.D. and Suresh, K. (2007), "Pullout behaviour of granular pile-anchors in expansive clay beds in situ", J. Geotech. Geoenvironmental Eng., 133(5).531-538. https://doi.org/10.1061/(ASCE)1090-0241(2007)133:5(531).
  30. Rowe, R.K. and Davis, E.H. (1982), "The behaviour of anchor plates in clay", Geotechnique, 32(1), 9-23. https://doi.org/10.1680/geot.1982.32.1.9.
  31. Stewart, W. (1985), "Uplift capacity of circular plate anchors in layered soil", Canadian Geotech. J., 22(4), 589-592. https://doi.org/10.1139/t85-078.
  32. Shin, E.C., Das, B.M., Puri, V.K., Yen, S.C. and. Cook, E.E. (1993), "Ultimate uplift capacity of model rigid metal piles in clay", GEotech. Geological Eng., 11(3), 203-215. https://doi.org/10.1007/BF00531251.
  33. Song, Z., Hu, Y. and Randolph, M.F. (2008), "Numerical simulation of vertical pullout of plate anchors in clay", J. Geotech. Geoenviron. Eng., 134(6), 866-875. https://doi.org/10.1061/(ASCE)1090-0241(2008)134:6(866).
  34. Sutherland, H.B. (1988), "Uplift resistance of Soils", Geotechnique, 38(4), 493-516. https://www.icevirtuallibrary.com/doi/pdf/10.1680/geot.1988.38.4.493.
  35. Tho, K.K., Chen, Z., Leung, C.F. and Chow, Y.K. (2014), "Pullout behaviour of plate anchor in clay with linearly increasing strength", Canadian Geotech. J., 51(1), 92-102. https://doi.org/10.1139/cgj-2013-0140.
  36. Vesic, A.S. (1971), "Breakout resistance of objects embedded in ocean bottom", J. Soil Mech. Foundation Eng., 97(9), 1183-1205. https://cedb.asce.org/CEDBsearch/record.jsp?dockey=0018421. https://doi.org/10.1061/JSFEAQ.0001659
  37. Wang, D., Hu, Y. and Randolph, M.F. (2010), "Three-dimensional large deformation finite-element analysis of plate anchors in uniform clay", J. Geotech. Geoenviron. Eng., 136(2), 355-365. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000210.
  38. Wu, X., Chow, Y. K. and Leung, C.F. (2019), "Numerical study of effect of fluke inclination on behavior of drag anchor in clay with linearly increasing shear strength under unidirectional and combined loading", Appl. Ocean Res., 91, 1-14. https://doi.org/10.1016/j.apor.2019.101883.
  39. Xu, H., Chen, L. and Deng, J. (2014), "Uplift tests of jet mixing anchor pile", Soils Foundations, 54(2), 168-175. https://doi.org/10.1016/j.sandf.2014.02.008.