Advances in concrete construction

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Impact resistant properties of Kagome truss reinforced composite panels

  • Choi, Jeong-Il (Biohousing Research Center, Chonnam National University) ;
  • Park, Se-Eon (Department of Architecture and Civil Engineering, Chonnam National University) ;
  • Lee, Sang-Kyu (Department of Architectural Engineering, Chungnam National University) ;
  • Kim, Gyu-Yong (Department of Architectural Engineering, Chungnam National University) ;
  • Hwang, Jae-Seung (Department of Architecture and Civil Engineering, Chonnam National University) ;
  • Lee, Bang Yeon (Department of Architecture and Civil Engineering, Chonnam National University)
  • Received : 2020.11.07
  • Accepted : 2021.11.02
  • Published : 2021.11.25
⟨ Previous Next ⟩

Abstract

This paper presents an experimental study exploring impact resistant properties of Kagome truss reinforced composite panels. Three types of panels with different materials and reinforcements, i.e., ultra-high-performance mortar, steel fiber, and Kagome truss, were designed and manufactured. High-velocity projectile impact tests were performed to investigate the impact response of panels with dimensions of 200 mm×200 mm×40 mm. The projectile used in the testing was a steel slug with a hemispherical front; the impact energy was 1 557 J. Test results showed that the Kagome truss reinforcement was effective at improving the impact resistance of panels in terms of failure patterns, damaged area, and mass loss. Synergy effects of a combination of Kagome truss and fiber reinforcements for the improvement of impact resistance capacity of ultra-high-performance mortar were also observed.

Keywords

Acknowledgement

This research was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIT) (No. 2019R1A2C4069794).

References

  1. Abbas, A., Cotsovos, D.M. and Behinaein, P. (2018), "Behaviour of steel-fibre-reinforced concrete beams under high-rate loading", Comput. Concrete, 22(3), 337-353. https://doi.org/10.12989/cac.2018.22.3.337.
  2. Abdel-Kader, M.M. and Fouda, A. (2017), "Improving the impact resistance of concrete panels by glass fiber reinforced polymer sheets", Int. J. Prot. Struct., 8(2), 304-320. https://doi.org/10.1177/2041419617712168.
  3. AFGC (2002), "Ultra-high performance fibre-reinforced concrete-interim recommendations", Assoc. Francaise de Genie Civil, Paris, France.
  4. ASTM (2007), Standard Test Method for Compressive Strength of Hydraulic Cement Mortars, American Society for Testing and Materials, ASTM International West Conshohocken, PA, USA.
  5. Beppu, M., Miwa, K., Itoh, M., Katayama, M. and Ohno, T. (2008), "Damage evaluation of concrete plates by high-velocity impact", Int. J. Impact Eng., 35(12), 1419-1426. https://doi.org/10.1016/j.ijimpeng.2008.07.021.
  6. Choi, J.I., Lee, B.Y., Ranade, R., Li, V.C. and Lee, Y. (2016), "Ultra-high-ductile behavior of a polyethylene fiber-reinforced alkali-activated slag-based composite", Cement Concrete Compos., 70, 153-158. https://doi.org/10.1016/j.cemconcomp.2016.04.002.
  7. Djamai, Z.I., Bahrar, M., Salvatore, F., Larbi, A.S. and El Mankibi, M. (2017), "Textile reinforced concrete multiscale mechanical modelling: Application to TRC sandwich panels", Finite Elem. Anal. Des., 135, 22-35. https://doi.org/10.1016/j.finel.2017.07.003.
  8. Graybeal, B.A. (2007), "Compressive behavior of ultra-high-performance fiber-reinforced concrete", ACI Mater. J., 104(2), 146.
  9. Hanif, A., Cheng, Y., Lu, Z. and Li, Z. (2018), "Mechanical behavior of thin-laminated cementitious composites incorporating cenosphere fillers", ACI Mater. J., 115(1), 117-127. https://doi.org/10.14359/51701007.
  10. Hazell, P.J. (2015), Armour: Materials, Theory, and Design, CRC Press.
  11. Huo, J., Li, Z., Zhao, L., Liu, J. and Xiao, Y. (2018), "Dynamic behavior of CFRP-strengthened reinforced concrete beams without stirrups under impact loading", ACI Struct. J., 115, 775-787.
  12. Husem, M., Cosgun, S.I. and Sesli, H. (2018), "Finite element analysis of RC walls with different geometries under impact loading", Comput. Concrete, 21(5), 583-592. https://doi.org/10.12989/cac.2018.21.5.583.
  13. Hwang, H.J., Zang, L. and Ma, G. (2019), "Effect of impact loading on bar development length in CCT node", J. Struct. Integr. Maint., 4(1), 26-36. https://doi.org/10.1080/24705314.2019.1565059.
  14. Hwang, J.S., Lee, K.S., Hur, M.W. and Lee, S.H. (2019), "Mechanical hysteresis model of a metal-wire Kagome truss for seismic strengthening for building systems", J. Asian Archit. Build. Eng., 18(2), 112-120. https://doi.org/10.1080/13467581.2019.1599898.
  15. JSCE (2008), "Recommendations for design and construction of high performance fiber reinforced cement composites with multiple fine cracks (HPFRCC)", Japan Soc. Civil Eng., Japan, March.
  16. Kang, K.J. (2015), "Wire-woven cellular metals: The present and future", Prog. Mater. Sci., 69, 213-307. https://doi.org/10.1016/j.pmatsci.2014.11.003.
  17. Kang, S.T. (2020), "The use of river sand for fine aggregate in UHPC and the effect of its particle size", Adv. Concrete Constr., 10(5), 431-441. https://doi.org/10.12989/acc.2020.10.5.431.
  18. Kang, S.T., Choi, J.I., Koh, K.T., Lee, K.S. and Lee, B.Y. (2016), "Hybrid effects of steel fiber and microfiber on the tensile behavior of ultra-high performance concrete", Compos. Struct., 145, 37-42. https://doi.org/10.1016/j.compstruct.2016.02.075.
  19. Karanth, S.S., Ghorpade, V.G. and Rao, H.S. (2017), "Shear and impact strength of waste plastic fibre reinforced concrete", Adv. Concrete Constr., 5(2), 173. https://doi.org/10.12989/acc.2017.5.2.173.
  20. Kennedy, R. (1976), "A review of procedures for the analysis and design of concrete structures to resist missile impact effects", Nucl. Eng. Des., 37(2), 183-203. https://doi.org/10.1016/0029-5493(76)90015-7.
  21. Kim, H., Kim, G., Gucunski, N., Nam, J. and Jeon, J. (2015), "Assessment of flexural toughness and impact resistance of bundle-type polyamide fiber-reinforced concrete", Compos. Part B Eng., 78(1), 431-446. https://doi.org/10.1016/j.compositesb.2015.04.011.
  22. Kim, H., Kim, G., Nam, J., Kim, J., Han, S. and Lee, S. (2015), "Static mechanical properties and impact resistance of amorphous metallic fiber-reinforced concrete", Compos. Struct., 134, 831-844. https://doi.org/10.1016/j.compstruct.2015.08.128.
  23. Kim, H., Lee, C.J., Shon, C.S., Moon, H. and Chung, C.W. (2020), "Mechanical performance and chloride ion penetration of polyolefin fiber reinforced concrete designed for shotcreting at marine environment", J. Struct. Integr. Maint., 5(1), 8-17. https://doi.org/10.1080/24705314.2019.1692164.
  24. Kim, S., Jeong, S.Y. and Kang, T.H.K. (2019), "Design of small impact test device for concrete panels subject to high speed collision", Adv. Concrete Constr., 7(1), 23. https://doi.org/10.12989/acc.2019.7.1.023.
  25. Kim, S., Park, C. and Kim, D.J. (2020), "Dynamic tensile behavior of SIFRCCs at high strain rates", Comput. Concrete, 26(3), 275-283. https://doi.org/10.12989/cac.2020.26.3.275.
  26. Lee, B.K. and Kang, K.J. (2010), "A parametric study on compressive characteristics of wire-woven bulk Kagome truss cores", Compos. Struct., 92(2), 445-453. https://doi.org/10.1016/j.compstruct.2009.08.029.
  27. Lee, M., Lee, K., Hur, H. and Kang, K. (2013), "Mechanical behavior of a wire-woven metal under compression", Compos. Struct., 95, 264-277. https://doi.org/10.1016/j.compstruct.2012.06.016.
  28. Li, P. and Yu, Q. (2019), "Responses and post-impact properties of ultra-high performance fibre reinforced concrete under pendulum impact", Compos. Struct., 208, 806-815. https://doi.org/10.1016/j.compstruct.2018.10.071.
  29. Liu, S., Zhu, D., Ou, Y., Yao, Y. and Shi, C. (2018), "Impact response of basalt textile reinforced concrete subjected to different velocities and temperatures", Constr. Build. Mater., 175, 381-391. https://doi.org/10.1016/j.conbuildmat.2018.04.193.
  30. Maalej, M., Quek, S.T. and Zhang, J. (2005), "Behavior of hybrid-fiber engineered cementitious composites subjected to dynamic tensile loading and projectile impact", J. Mater. Civil Eng., 17(2), 143-152. https://doi.org/10.1061/(ASCE)0899-1561(2005)17:2(143).
  31. Munjal, P. and Singh, S. (2020), "Out-of-plane response of ECC-strengthened masonry walls", J. Struct. Integr. Maint., 5(1), 18-30. https://doi.org/10.1080/24705314.2019.1692165.
  32. Naaman, A.E. (2000), Ferrocement and Laminated Cementitious Composites, Techno Press, Ann Arbor.
  33. Park, S.H., Kim, D.J., Ryu, G.S. and Koh, K.T. (2012), "Tensile behavior of ultra high performance hybrid fiber reinforced concrete", Cement Concrete Compos., 34(2), 172-184. https://doi.org/10.1016/j.cemconcomp.2011.09.009.
  34. Portal, N.W., Flansbjer, M., Zandi, K., Wlasak, L. and Malaga, K. (2017), "Bending behaviour of novel Textile Reinforced Concrete-foamed concrete (TRC-FC) sandwich elements", Compos. Struct., 177, 104-118. https://doi.org/10.1016/j.compstruct.2017.06.051.
  35. Rahman, I.A., Zaidi, A.M.A., Bux, Q. and Latif, I. (2010), "Review on empirical studies of local impact effects of hard missile on concrete structures", Int. J. Sustain. Constr. Eng. Tech., 1(1), 73-98.
  36. Siddika, A., Al Mamun, M.A., Ferdous, W. and Alyousef, R. (2020), "Performances, challenges and opportunities in strengthening reinforced concrete structures by using FRPs-A state-of-the-art review", Eng. Fail. Anal., 111, 104480. https://doi.org/10.1016/j.engfailanal.2020.104480.
  37. Siddiqui, N.A., Al-Salloum, Y.A., Almusallam, T.H., Abadel, A.A. and Abbas, H. (2018), "Reliability assessment of hfrc slabs against projectile impact", Int. J. Concrete Struct. Mater., 12(1), 58. https://doi.org/10.1186/s40069-018-0289-9.
  38. Singh, S.B., Chauhan, A. and Munjal, P. (2018), "Composite mechanics-based design approach for FRP-strengthened walls", J. Struct. Integr. Maint., 3(3), 160-170. https://doi.org/10.1080/24705314.2018.1492670.
  39. Ulzurrun, G.S. and Zanuy, C. (2017), "Enhancement of impact performance of reinforced concrete beams without stirrups by adding steel fibers", Constr. Build. Mater., 145, 166-182. https://doi.org/10.1016/j.conbuildmat.2017.04.005.
  40. Wang, S., Naaman, A.E. and Li, V.C. (2004), "Bending response of hybrid ferrocement plates with meshes and fibers", J. Ferroce., 34(1), 275-288.
  41. Yang, Y., Wang, Y., Chen, Y. and Zhang, B. (2019), "Test study on the impact resistance of steel fiber reinforced full lightweight concrete beams", Earthq. Struct., 17(6), 567-575. https://doi.org/10.12989/eas.2019.17.6.567.
  42. Yerramala, A., Chandurdu, C.R. and Desai, V.B. (2016), "Impact strength of metakaolin ferrocement", Mater. Struct., 49(1-2), 5-15. https://doi.org/10.1617/s11527-014-0469-2.
  43. Yoo, D.Y. and Banthia, N. (2017), "Mechanical and structural behaviors of ultra-high-performance fiber-reinforced concrete subjected to impact and blast", Constr. Build. Mater., 149, 416-431. https://doi.org/10.1617/s11527-014-0469-2.
  44. Yoo, D.Y. and Banthia, N. (2019), "Impact resistance of fiber-reinforced concrete-A review", Cement Concrete Compos., 104, 103389. https://doi.org/10.1016/j.cemconcomp.2019.103389.