DOI QR코드

DOI QR Code

Improving the brittle behaviour of high-strength concrete using keratin and glass fibres

  • Abdelsamie, Khaled (Faculty of Engineering, Sohag University) ;
  • Agwa, Ibrahim Saad (Civil and Architectural Constructions Department, Faculty of Technology and Education, Suez University) ;
  • Tayeh, Bassam A. (Civil Engineering Department, Faculty of Engineering, Islamic University of Gaza) ;
  • Hafez, Radwa Defalla Abdel (Civil and Architectural Constructions Department, Faculty of Technology and education, Sohag University)
  • Received : 2021.02.17
  • Accepted : 2021.11.16
  • Published : 2021.12.25

Abstract

Keratin fibres are waste products of the poultry industry. Natural materials made from chicken feather fibres (CFFs) are used in concrete-reinforced composites in this study. Brittleness is a major problem of high-strength concrete (HSC) that leads to sudden failure at the ultimate capacity of concrete. Hence, this work aims to investigate effects of using CFFs on improving the brittle behaviour of HSC. Two scenarios are performed to analyse the effectiveness of using CFFs. HSC containing different ratios of CFF (0% as the control, 0.5%, 1%, 1.5%, 2%, and 3%) by volume are tested in the first scenario. Glass fibres (GF) are used to replace CFFs in the other scenario. Tests of fresh, hardened and morphological properties for concrete are performed. Results showed the enhanced brittle behaviour of HSC when using both types of fibres. The preferable ratio of both types of fibres is 1% by volume. Flexural and splitting tensile strengths increased by about 44.9 % and 42.65 % for mixes containing 0.1% GF, respectively. While they were increased by about 21.6 % and 21.16 % for mixes containing 0.1% CFF, respectively.

Keywords

References

  1. Abdul-Rahman, M., Al-Attar, A.A., Hamada, H.M. and Tayeh, B. (2020), "Microstructure and structural analysis of polypropylene fibre reinforced reactive powder concrete beams exposed to elevated temperature", J. Build. Eng., 29, 101167. https://doi.org/10.1016/j.jobe.2019.101167.
  2. Acda, M.N. (2010), "Sustainable use of waste chicken feather for durable and low cost building materials for tropical climates", Sustain. Agr. Tech. Plan. Manag., 353-366.
  3. Acda, M.N. (2010), "Waste chicken feather as reinforcement in cement-bonded composites", Philippine J. Sci., 139(2), 161-166.
  4. Agwa, I.S., Omar, O.M., Tayeh, B.A. and Abdelsalam, B.A. (2020), "Effects of using rice straw and cotton stalk ashes on the properties of lightweight self-compacting concrete", Constr. Build. Mater., 235, 117541. https://doi.org/10.1016/j.conbuildmat.2019.117541.
  5. Al-Attar, A.A., Abdulrahman, M.B., Hamada, H.M. and Tayeh, B.A. (2020), "Investigating the behaviour of hybrid fibre-reinforced reactive powder concrete beams after exposure to elevated temperatures", J. Mater. Res. Tech., 9, 1966-1 977. https://doi.org/10.1016/j.jmrt.2019.12.029.
  6. Al Saffar, D.M., Al Saad, A.J. and Tayeh, B.A. (2019), "Effect of internal curing on behavior of high performance concrete: An overview", Case Stud. Constr. Mater., 10, e00229. https://doi.org/10.1016/j.cscm.2019.e00229.
  7. Ali, T.K.M., Hilal, N., Faraj, R.H. and Al-Hadithi, A.I. (2020), "Properties of eco-friendly pervious concrete containing polystyrene aggregates reinforced with waste pet fibers", Innov. Infrastruct. Solution., 5(3), 1-16. https://doi.org/10.1007/s41062-020-00323-w.
  8. Amin, M. and Tayeh, B.A. (2020), "Investigating the mechanical and microstructure properties of fibre-reinforced lightweight concrete under elevated temperatures", Case Stud. Constr. Mater., 13, e00459. https://doi.org/10.1016/j.cscm.2020.e00459.
  9. Amin, M., Tayeh, B.A. and Agwa, I.S. (2020), "Effect of using mineral admixtures and ceramic wastes as coarse aggregates on properties of ultrahigh-performance concrete", J. Clean. Prod., 273, 123073. https://doi.org/10.1016/j.jclepro.2020.123073.
  10. Amin, M., Zeyad, A.M., Tayeh, B.A. and Agwa, I.S. (2021), "Effects of nano cotton stalk and palm leaf ashes on ultrahigh-performance concrete properties incorporating recycled concrete aggregates", Constr. Build. Mater., 302, 124196. https://doi.org/10.1016/j.conbuildmat.2021.124196.
  11. Amin, M., Zeyad, A.M., Tayeh, B.A. and Agwa, I.S. (2021), "Engineering properties of self-cured normal and high strength concrete produced using polyethylene glycol and porous ceramic waste as coarse aggregate", Constr. Build. Mater., 299, 124243. https://doi.org/10.1016/j.conbuildmat.2021.124243.
  12. Aranberri, I., Montes, S., Azcune, I., Rekondo, A. and Grande, H.J. (2017), "Fully biodegradable biocomposites with high chicken feather content", Polym., 9(11), 593. https://doi.org/10.3390/polym9110593.
  13. ASTM A.S. (2019), Standard Specification for Portland Cement (ASTM C150/C150M-19A)
  14. ASTM C. (2002), Standard Test Method for Static Modulus of Elasticity and Poisson's Ratio of Concrete in Compression, Annual Book of ASTM Standards.
  15. ASTM C. (2003), Standard specification for concrete aggregates, American Society for Testing and Materials, Philadelphia, PA, USA.
  16. Babalola, R., Ayeni, A.O., Joshua, P.S., Ayoola, A.A., Isaac, U.O., Aniediong, U., Efeovbokhan, V.E. and Omoleye, J.A. (2020), "Synthesis of thermal insulator using chicken feather fibre in starch-clay nanocomposites", Heliyon, 6(11), e05384. https://doi.org/10.1016/j.heliyon.2020.e05384.
  17. Bansal, G. and Singh, V. (2016), "Review on chicken feather fiber (CFF) a livestock waste in composite material development", Int. J. Waste Resour, 6(2), 1000254. https://doi.org/10.4172/2252-5211.1000254.
  18. Bansal, G., Singh, V., Gope, P. and Gupta, T. (2017), "Application and properties of chicken feather fiber (CFF) a livestock waste in composite material development", J. Graphic Era U., 5(1), 16-24.
  19. Bessa, J., Souza, J., Lopes, J., Sampaio, J., Mota, C., Cunha, F. and Fangueiro, R. (2017), "Characterization of thermal and acoustic insulation of chicken feather reinforced composites", Proc. Eng., 200, 472-479. https://doi.org/10.1016/j.proeng.2017.07.066.
  20. Boulekbache, B., Hamrat, M., Chemrouk, M. and Amziane, S. (2016), "Flexural behaviour of steel fibre-reinforced concrete under cyclic loading", Constr. Build. Mater., 126, 253-262. https://doi.org/10.1016/j.conbuildmat.2016.09.035.
  21. Brandelli, A., Sala, L. and Kalil, S.J. (2015), "Microbial enzymes for bioconversion of poultry waste into added-value products", Food Res. Int., 73, 3-12. https://doi.org/10.1016/j.foodres.2015.01.015.
  22. British Standard (1881), Testing Concrete-Part 116, Method for Determination of Compressive Strength of Concrete Cubes.
  23. Buyukkaya, K. (2017), "Effects of the fiber diameter on mechanic properties in polymethyl-methacrylate composites reinforced with goose feather fiber", Mater. Sci. Appl., 8(11), 811-827. https://doi.org/10.4236/msa.2017.811059.
  24. C143 A. (2010), Standard Test Method for Slump of Hydraulic-Cement Concrete, ASTM International West Conshohocken, PA, USA.
  25. Concrete, A.I.C.C.o. and Aggregates, C. (2010), Standard Test Method for Flexural Strength of Concrete (using simple beam with center-point loading), ASTM International.
  26. Concrete, A.I.C.C.o. and Aggregates, C. (2017), Standard test method for splitting tensile strength of cylindrical concrete specimens1, ASTM international.
  27. Dalhat, M., Osman, S., Alhuraish, A.A.A., Almarshad, F.K., Qarwan, S.A. and Adesina, A.Y. (2020), "Chicken feather fiber modified hot mix asphalt concrete: Rutting performance, durability, mechanical and volumetric properties", Constr. Build. Mater., 239, 117849. https://doi.org/10.1016/j.conbuildmat.2019.117849.
  28. de Azevedo, A.R., Marvila, M.T., Tayeh, B.A., Cecchin, D., Pereira, A.C. and Monteiro, S.N. (2021), "Technological performance of acai natural fibre reinforced cement-based mortars", J. Build. Eng., 33, 101675. https://doi.org/10.1016/j.jobe.2020.101675.
  29. El-Hawary, M.M. and Hamoush, S.A. (1994), "Strength of concrete reinforced with treated feathers", Constr. Build. Mater., 8(3), 173-176. https://doi.org/10.1016/j.jobe.2020.101675.
  30. Faried, A.S., Mostafa, S.A., Tayeh, B.A. and Tawfik, T.A. (2021a), "Mechanical and durability properties of ultra-high performance concrete incorporated with various nano waste materials under different curing conditions", J. Build. Eng., 43, 102569. https://doi.org/10.1016/j.jobe.2021.102569.
  31. Faried, A.S., Mostafa, S.A., Tayeh, B.A. and Tawfik, T.A. (2021b), "The effect of using nano rice husk ash of different burning degrees on ultra-high-performance concrete properties", Constr. Build. Mater., 290, 123279. https://doi.org/10.1016/j.conbuildmat.2021.123279.
  32. Fayomi, O., Babaremu, K., Akande, I., Agboola, O. and Anyanwu, B. (2020), "Potential of bio-wastes in the development of composites for manufacturing application", Mater. Today Proc., 38(5), 2353-2357. https://doi.org/10.1016/j.matpr.2020.06.539.
  33. Gumus, M. and Arslan, A. (2019), "Effect of fiber type and content on the flexural behavior of high strength concrete beams with low reinforcement ratios", Struct., 20, 10-15. https://doi.org/10.1016/j.istruc.2019.02.018.
  34. Gupta, T., Chaudhary, S. and Sharma, R.K. (2016), "Mechanical and durability properties of waste rubber fiber concrete with and without silica fume", J. Clean. Prod., 112, 702-711. https://doi.org/10.1016/j.jclepro.2015.07.081.
  35. Haido, J. H., Zainalabdeen, M.A. and Tayeh, B.A. (2021), "Experimental and numerical studies on flexural behavior of high strength concrete beams containing waste glass", Adv. Concrete Constr., 11(3), 239-253. https://doi.org/10.12989/acc.2021.11.3.239.
  36. Haido, J.H., Tayeh, B.A., Majeed, S.S. and Karpuzcu, M. (2021a), "Effect of high temperature on the mechanical properties of basalt fibre self-compacting concrete as an overlay material", Constr. Build. Mater., 268, 121725. https://doi.org/10.1016/j.conbuildmat.2020.121725.
  37. Hamoush, S.A. and El-Hawary, M.M. (1994), "Feather fiber reinforced concrete", Concrete Int., 16(6), 33-35.
  38. Hara, N., Morisada, S., Ohto, K. and Kawakita, H. (2014), "Papain activity in dextran solution for keratin hydrolysis", Adv. Enzyme Res., 2(1), 43906. https://doi.org/10.4236/aer.2014.21005.
  39. Hilal, N., Al Saffar, D.M. and Ali, T.K.M. (2021), "Effect of egg shell ash and strap plastic waste on properties of high strength sustainable self-compacting concrete", Arab. J. Geosci., 14(4), 1-11. https://doi.org/10.1007/s12517-021-06654-x.
  40. Hilal, N., Ali, T.K.M. and Tayeh, B.A. (2020), "Properties of environmental concrete that contains crushed walnut shell as partial replacement for aggregates", Arab. J. Geosci., 13(16), 1-9. https://doi.org/10.1007/s12517-020-05733-9.
  41. Ibrahim, O.M.O., Heniegal, A.M., Ibrahim, K.G. and Agwa, I.S. (2020), "Effect of horizontal joints on structural behavior of sustainable self-compacting reinforced concrete beams", Adv. Concrete Constr., 10(5), 455-462. https://doi.org/10.12989/acc.2020.10.5.455.
  42. Jaradat, O.Z., Gadri, K., Tayeh, B.A. and Guettalaa, A. (2021), "Influence of sisal fibres and rubber latex on the engineering properties of sand concrete", Struct. Eng. Mech., 80(1), 47-62. https://doi.org/10.12989/sem.2021.80.1.047.
  43. Karshan, M. (1930), "The chemistry and staining reactions of keratin", J. Dental Res., 10(2), 181-186. https://doi.org/10.1177/00220345300100020401.
  44. Kim, J. and Lee, H. (2021), "Thermomechanical behavior of alkali-activated slag/fly ash composites with pva fibers exposed to elevated temperatures", Adv. Concrete Constr., 11(1), 11. https://doi.org/10.12989/acc.2021.11.1.011.
  45. Kodak, S., Gharge, T. and Chavan, V. (2019), "Microbial degradation of poultry feather wastes under the influence of temperature and ph a€" A review", Int. J. Envir. Sci. Nat. Res., 21(3), 87-92. https://doi.org/10.19080/IJESNR.2019.21.556063.
  46. M-19 A.C.C. (2019), Standard specification for chemical admixtures for concrete, Annual book of astm standards, ASTM International West Conshohocken, PA, USA.
  47. Manginsay, G.P. and Cabahug, R.G. (2015), "Chicken feathers as substitute for fine aggregates in concrete", Mindanao J. Sci. Tech., 13.
  48. Mansour, W. and Tayeh, B.A. (2020), "Shear behaviour of RC beams strengthened by various ultrahigh performance fibre-reinforced concrete systems", Adv. Civil Eng., 2020, 2139054. https://doi.org/10.1155/2020/2139054.
  49. Mendoza, R.C., Grande, J.O. and Acda, M.N. (2019), "Effect of keratin fibers on setting and hydration characteristics of portland cement", J. Nat. Fiber., 18(11), 1801-1808. https://doi.org/10.1080/15440478.2019.1701604.
  50. Mrajji, O., Wazna, M.E., Boussoualem, Y., Bouari, A.E. and Cherkaoui, O. (2019), "Feather waste as a thermal insulation solution: Treatment, elaboration and characterization", J. Indust. Textile., 50, 1674-1697. https://doi.org/10.1177/1528083719869393.
  51. Ouakarrouch, M., Laaroussi, N. and Garoum, M. (2020), "Thermal characterization of a new bio-composite building material based on plaster and waste chicken feathers", Renew. Ener. Envir. Sustain., 5(2), 7. https://doi.org/10.1051/rees/2019011.
  52. Palmquist, S.M. and Jansen, D.C. (2001), "Postpeak strain-stress relationship for concrete in compression", Mater. J., 98(3), 213-219.
  53. Pavithra, C., Arokiaprakash, A. and Maheshwari, A. (2020), "Behaviour of concrete adding chicken feather as fibre with partial replacement of cement with cashewnut shell powder", Mater. Today Proc., 43(2), 1173-178. https://doi.org/10.1016/j.matpr.2020.08.731.
  54. Peng, Z., Mao, X., Zhang, J., Du, G. and Chen, J. (2019), "Effective biodegradation of chicken feather waste by co-cultivation of keratinase producing strains", Microbial Cell Fact., 18(1), 1-11. https://doi.org/10.1186/s12934-019-1134-9.
  55. Perumal, R. and Prabakaran, V. (2020), "Estimating the compressive strength of hpfrc containing metallic fibers using statistical methods and anns", Adv. Concrete Constr., 10(6), 479. https://doi.org/10.12989/acc.2020.10.6.479.
  56. Poole, A.J., Church, J.S. and Huson, M. G. (2009), "Environmentally sustainable fibers from regenerated protein", Biomacromolecules, 10(1), 1-8. https://doi.org/10.1021/bm8010648.
  57. Saad, M., Agwa, I.S., Abdelsalam Abdelsalam, B. and Amin, M. (2020), "Improving the brittle behavior of high strength concrete using banana and palm leaf sheath fibers", Mech. Adv. Mater. Struct., 1-10. https://doi.org/10.1080/15376494.2020.1780352.
  58. Schmidt, W. (1998), "Innovative feather utilization strategies", Proceedings of the 1998 National Poultry Waste Management Symposium.
  59. Taskin, M. and Kurbanoglu, E. (2011), "Evaluation of waste chicken feathers as peptone source for bacterial growth", J. Appl. Microb., 111(4), 826-834. https://doi.org/10.1111/j.1365-2672.2011.05103.x.
  60. Tayeh, B.A., Al Saffar, D.M. and Alyousef, R. (2020), "The utilization of recycled aggregate in high performance concrete: A review", J. Mater. Res. Tech., 9(4), 8469-8481. https://doi.org/10.1016/j.jmrt.2020.05.126.
  61. Tesfaye, T., Sithole, B., Ramjugernath, D. and Mokhothu, T. (2018), "Valorisation of chicken feathers: Characterisation of thermal, mechanical and electrical properties", Sustain. Chem. Pharm., 9, 27-34. https://doi.org/10.1016/j.scp.2018.05.003.
  62. Tobbala, D., Abdelsalam, B.A. and Agwa, I.S. (2020), "Bond performance of a hybrid coating zinc-rich epoxy incorporating nano-ferrite for steel rebars subjected to high temperatures in concrete", J. Build. Eng., 32, 101698. https://doi.org/10.1016/j.jobe.2020.101698.
  63. Vaha-Nissi, M., Lahtinen, P., Nuutinen, E., Kaljunen, T. and Pohler, T. (2019), "Films from an aqueous suspension of alkaline pretreated and fine milled chicken feathers", Mater. Sci. Appl., 11(1), 27-43. https://doi.org/10.4236/msa.2020.111003.
  64. Ward, W., Binkley, C. and Snell, N. (1955), "Amino acid composition of normal wools, wool fractions, mohair, feather, and feather fractions", Textile Res. J., 25(4), 314-325. https://doi.org/10.1177/004051755502500403.
  65. Zeyad, A.M., Johari, M.A.M., Abutaleb, A. and Tayeh, B.A. (2021b), "The effect of steam curing regimes on the chloride resistance and pore size of high-strength green concrete", Constr. Build. Mater., 280, 122409. https://doi.org/10.1016/j.conbuildmat.2021.122409.
  66. Zeyad, A.M., Johari, M.A.M., Alharbi, Y.R., Abadel, A.A., Amran, Y.M., Tayeh, B.A. and Abutaleb, A. (2021a), "Influence of steam curing regimes on the properties of ultrafine POFA-based high-strength green concrete", J. Build. Eng., 38, 102204. https://doi.org/10.1016/j.jobe.2021.102204.