Smart Structures and Systems

  • 제26권5호
  • /
  • Pages.605-617
  • /
  • 2020
  • /
  • 1738-1584(pISSN)
  • /
  • 1738-1991(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Numerical simulation of compressive to tensile load conversion for determining the tensile strength of ultra-high performance concrete

  • Haeri, Hadi (State Key Laboratory for Deep GeoMechanics and Underground Engineering) ;
  • Mirshekari, Nader (Department of Civil Engineering, Islamic Azad University) ;
  • Sarfarazi, Vahab (Department of Mining Engineering, Hamedan University of Technology) ;
  • Marji, Mohammad Fatehi (Department of Mine Exploitation Engineering, Faculty of Mining and metallurgy, Institute of Engineering, Yazd University)
  • 투고 : 2019.12.29
  • 심사 : 2020.06.30
  • 발행 : 2020.11.25
⟨ 이전 논문 다음 논문 ⟩

초록

In this study, the experimental tests for the direct tensile strength measurement of Ultra-High Performance Concrete (UHPC) were numerically modeled by using the discrete element method (circle type element) and Finite Element Method (FEM). The experimental tests used for the laboratory tensile strength measurement is the Compressive-to-Tensile Load Conversion (CTLC) device. In this paper, the failure process including the cracks initiation, propagation and coalescence studied and then the direct tensile strength of the UHPC specimens measured by the novel apparatus i.e., CTLC device. For this purpose, the UHPC member (each containing a central hole) prepared, and situated in the CTLC device which in turn placed in the universal testing machine. The direct tensile strength of the member is measured due to the direct tensile stress which is applied to this specimen by the CTLC device. This novel device transferring the applied compressive load to that of the tensile during the testing process. The UHPC beam specimen of size 150 × 60 × 190 mm and internal hole of 75 × 60 mm was used in this study. The rate of the applied compressive load to CTLC device through the universal testing machine was 0.02 MPa/s. The direct tensile strength of UHPC was found using a new formula based on the present analyses. The numerical simulation given in this study gives the tensile strength and failure behavior of the UHPC very close to those obtained experimentally by the CTLC device implemented in the universal testing machine. The percent variation between experimental results and numerical results was found as nearly 2%. PFC2D simulations of the direct tensile strength measuring specimen and ABAQUS simulation of the tested CTLC specimens both demonstrate the validity and capability of the proposed testing procedure for the direct tensile strength measurement of UHPC specimens.

키워드

참고문헌

  1. Abrishambaf, A., Barros, J.A. and Cunha, V.M. (2015), "Tensile stress-crack width law for steel fibre reinforced self-compacting concrete obtained from indirect (splitting) tensile tests", Cement Concrete Compos., 57, 153-165. https://doi.org/10.1016/j.cemconcomp.2014.12.010.
  2. Akbas, S. (2016), "Analytical solutions for static bending of edge cracked micro beams", Struct. Eng. Mech., Int. J., 59(3), 579-599. https://doi.org/10.12989/sem.2016.59.3.579.
  3. Alhussainy, F., Hasan, H.A., Rogic, S., Sheikh, M.N. and Hadi, M.N. (2016), "Direct tensile testing of self-compacting concrete", Constr. Build. Mater., 112, 903-906. https://doi.org/10.1016/j.conbuildmat.2016.02.215.
  4. Aliabadian, Z., Zhao, G.F. and Russell, A.R. (2019), "Failure, crack initiation and the tensile strength of transversely isotropic rock using the Brazilian test", Int. J. Rock Mech. Min. Sci., 122, 104073. https://doi.org/10.1016/j.ijrmms.2019.104073.
  5. ASTM D2936-08 (2008), Standard Test Method for Direct Tensile Strength of Intact Rock Core Specimens, Annual Book of ASTM Standards, ASTM, West Conshohocken, USA.
  6. ASTM D2938-86 (1986), Test Method for Unconfined Compressive Resistance of Intact Rock Core Specimens, ASTM Designation, USA.
  7. ASTM D3967-16 (2008), Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens, Annual Book of ASTM Standards, ASTM, West Conshohocken, USA.
  8. Bi, J., Zhou, X.P. and Qian, Q. (2016), "The 3D numerical simulation for the propagation process of multiple pre-existing flaws in rock-like materials subjected to biaxial compressive loads", Rock Mech. Rock Eng., 49(5), 1611-1627. https://doi.org/10.1007/s00603-015-0867-y.
  9. Bieniawski, Z.T. and Hawkes, I. (1978), "Suggested method for determining tensile strength of rock materials", Int. J. Rock Mech. Min. Sci. Geomech., 1, 99-103.
  10. CEB-FIB (2010), The Fib Model Code for Concrete Structures Case Postale 88, CH-1015 Lausanne, Switzerland.
  11. Chen, W.F. and Trumbauer, B.E. (1972), "Double-punch test and tensile strength of concrete", J. Mater., 7(2) 148-154. https://doi.org/10.1007/BF02403500
  12. Cundall, P.A. and Strack, O.D.L. (1979), "A discrete numerical model for granular assemblies", Geotechnique, 29(1), 47-65. https://doi.org/10.1680/geot.1979.29.1.47.
  13. Donze, F.V., Richefeu, V. and Magnier, S.A. (2009), "Advances in discrete element method applied to soil rock and concrete mechanics", Elec. J. Geol. Eng., 8, 1-44.
  14. Erarslan, N. and Williams, D.J. (2012), "Experimental, numerical and analytical studies on tensile strength of rocks", Int. J. Rock Mech. Min. Sci., 49, 21-30. https://doi.org/10.1016/j.ijrmms.2011.11.007.
  15. Ghaffar, A., Chaudhry, M.A. and Kamran Ali, M. (2005), "A new approach for measurement of tensile strength of concrete", J. Res. Sci., 16(1), 1-9.
  16. Hibbitt, H.D., Karlsson, B.I. and Sorensen, E.P. (2012), ABAQUS User's Manual, Dassault Systemes Simulia Corp., USA.
  17. Hillerborg, A. (1989), The Compression Stress-Strain Curve for Design of Reinforced Concrete Beams, Fracture Mechanics: Application to Concrete, ACI-SP-118, Detroit, USA.
  18. Hordijk, D.A. (1992), "Tensile and tensile fatigue behaviour of concrete experiments, modelling and analyses", Heron, 37(1), 3-79.
  19. Itasca Consulting Group Inc. (2003), "PFC2D (particle flow code in 2dimensions) version 3.0", ICGI, 41(8), 1329-1364.
  20. Khan, M.I. (2012), "Direct tensile strength measurement of concrete", Appl. Mech. Mater., 117, 9-14. https://doi.org/10.4028/www.scientific.net/AMM.117-119.9.
  21. Kim, J. and Taha, M.R. (2014), "Experimental and numerical evaluation of direct tension test for cylindrical concrete specimens", Adv. Civ. Eng., 2014, 156926. https://doi.org/10.1155/2014/156926.
  22. Li, S., Wang, H., Li, Y., Li, Q., Zhang, B. and Zhu, H. (2016), "A new mini-grating absolute displacement measuring system for static and dynamic geomechanical model tests", Measurement, 82, 421-431. https://doi.org/10.1016/j.measurement.2017.04.002.
  23. Liao, Z.Y., Zhu, J.B. and Tang, C.A. (2019), "Numerical investigation of rock tensile strength determined by direct tension, Brazilian and three-point bending tests", Int. J. Rock Mech. Min. Sci., 115, 21-32. https://doi.org/10.1016/j.ijrmms.2019.01.007.
  24. Liu, Y., Dai, F., Xu, N., Zhao, T. and Feng, P. (2018), "Experimental and numerical investigation on the tensile fatigue properties of rocks using the cyclic flattened Brazilian disc method", Soil Dyn. Earthq. Eng., 105, 68-82. https://doi.org/10.1016/j.soildyn.2017.11.025.
  25. Martin, C.D. (2014), "The direct and Brazilian tensile strength of rock in the light of size effect and bimodularity", Proceedings of the American Rock Mechanics Association: 48th U.S. Rock Mechanics/Geomechanics Symposium, Minneapolis, M.N., USA.
  26. Mier, V.J. (1986), "Multiaxial strain-softening of concrete", Mater. Struct., 19(111), 179-200. https://doi.org/10.1007/BF02472035.
  27. Mohammad, A. (2016), "Statistical flexural toughness modeling of ultra-high-performance concrete using response surface method", Comput. Concrete, Int. J., 17(4), 477-488. https://doi.org/10.12989/cac.2016.17.4.477.
  28. Omar, H., Ahmad, J., Nahazanan, H., Mohammed, T.A. and Yusoff, Z.M. (2018), "Measurement and simulation of diametrical and axial indirect tensile tests for weak rocks", Measurement, 127, 299-307. https://doi.org/10.1016/j.measurement.2018.05.067.
  29. Pan, B., Gao, Y. and Zhong, Y. (2014), "Theoretical analysis of overlay resisting crack propagation in old cement concrete pavement", Struct. Eng. Mech., Int. J., 52(4), 167-181. https://doi.org/10.12989/sem.2014.52.4.829.
  30. Potyondy, D.O. and Cundall, P.A. (2004), "A bonded-particle model for rock", Int. J. Rock Mech. Min. Sci., 41(8), 1329-1364. https://doi.org/10.1016/j.ijrmms.2004.09.011.
  31. Ramadoss, P. (2014), "Combined effect of silica fume and steel fibers on the splitting tensile strength of high-strength concrete", Int. J. Civ. Eng., 12(1), 99-103.
  32. Ramadoss, P. and Nagamani, K. (2006), "Investigations on the tensile strength of high-performance fiber reinforced concrete using statistical methods", Comput. Concrete, Int. J., 3(6), 389-400. https://doi.org/10.12989/cac.2006.3.6.389.
  33. Ramadoss, P. and Nagamani, K. (2008), "Tensile strength and durability characteristics of high-performance fiber reinforced concrete", Arab. J. Sci. Eng., 33(2), 307-319.
  34. Ramadoss, P. and Nagamani, K. (2013), "Stress-strain behavior and toughness of high-performance steel fiber reinforced concrete in compression", Comput. Concrete., Int. J., 11(2), 149-167. https://doi.org/10.12989/cac.2013.11.2.149.
  35. Sardemir, M. (2016), "Empirical modeling of flexural and splitting tensile strengths of concrete containing fly ash by GEP", Comput. Concrete, Int. J., 17(4), 489-498. https://doi.org/10.12989/cac.2016.17.4.489.
  36. Sarfarazi, V., Ghazvinian, A., Schubert, W., Nejati, H. and Hadei, R. (2016), "A new approach for measurement of tensile strength of concrete", Periodica Polytech. Civ. Eng., 60(2), 199-203. https://doi.org/10.3311/PPci.8328.
  37. Sarfarazi, V., Haeri, H. and Bagher Shemirani, A. (2017), "Direct and indirect methods for determination of mode I fracture toughness using PFC2D", Comput. Concrete, Int. J., 20(1), 39-47. https://doi.org/10.12989/cac.2017.20.1.039.
  38. Shang, J., Duan, K., Gui, Y., Handley, K. and Zhao, Z. (2018), "Numerical investigation of the direct tensile behaviour of laminated and transversely isotropic rocks containing incipient bedding planes with different strengths", Comput. Geotech., 104, 373-388. https://doi.org/10.1016/j.compgeo.2017.11.007.
  39. Shaowei, H., Aiqing, X., Xin, H. and Yangyang, Y. (2016), "Study on fracture characteristics of reinforced concrete wedge splitting tests", Comput. Concrete, Int. J., 18(3), 337-354. https://doi.org/10.12989/cac.2016.18.3.337.
  40. Shuraim, A.B., Aslam, F., Hussain, R. and Alhozaimy, A. (2016), "Analysis of punching shear in high strength RC panelsexperiments, comparison with codes and FEM results", Comput. Concrete, Int. J., 17(6), 739-760. https://doi.org/10.12989/cac.2016.17.6.739.
  41. Silva, R.V., De Brito, J. and Dhir, R.K. (2015), "Tensile strength behaviour of recycled aggregate concrete", Constr. Build. Mater., 83, 108-118. https://doi.org/10.1016/j.conbuildmat.2015.03.034.
  42. Swaddiwudhipong, S., Lu, H.R. and Wee, T.H. (2003), "Direct tension test and tensile strain capacity of concrete at early age", Cem. Concrete Res., 33, 2077-2084. https://doi.org/10.1016/S0008-8846(03)00231-X.
  43. Tran, K.Q., Satomi, T. and Takahashi, H. (2019), "Tensile behaviors of natural fiber and cement reinforced soil subjected to direct tensile test", J. Build. Eng., 24, 100748. https://doi.org/10.1016/j.jobe.2019.100748.
  44. Van Mier, J.G.M. (1992), "Assesment of strain softening curves for concrete", TU Delft, Mekelweg, Netherlands.
  45. Vonk, R.A. (1993), "A micromechanical investigation of softening of concrete loaded in compression", Heron, 38(3), 3-94.
  46. Wang, Q., Jias, X., Kou, S., Zang, Z. and Lindqvist, P.A. (2004), "The flattened Brazilian disc specimen used for testing elastic modulus, tensile strength and fracture toughness of brittle rocks: Analytical and numerical results", Int. J. Rock Mech. Min. Sci., 41, 245-253. https://doi.org/10.1016/S1365-1609(03)00093-5.
  47. Wei, X.X. and Chau, K.T. (2013), "Three dimensional analytical solution for finite circular cylinders subjected to indirect tensile test", Int. J. Solids Struct., 50, 2395-2406. https://doi.org/10.1016/j.ijsolstr.2013.03.026.
  48. Xie, N.X. and Liu, W.Y. (1989), "Determining tensile properties of mass concrete by direct tensile test", ACI Mater. J., 86(3) 214-219.
  49. Yaylac, M. (2016), "The investigation crack problem through numerical analysis", Struct. Eng. Mech., Int. J., 57(6), 1143-1156. https://doi.org/10.12989/sem.2016.57.6.1143.
  50. Zain, M.F.M., Mahmud, H.B., Ilham, A. and Faizal, M. (2002), "Splitting tensile strength of high-performance concrete", Cem. Concrete. Res., 32, 1251-1257. https://doi.org/10.1016/S0008-8846(02)00768-8
  51. Zhang, Z.X. (2002), "An empirical relation between mode I fracture toughness and the tensile strength of rock", Int. J. Rock Mech. Min. Sci. Geomech., 93, 401-406. https://doi.org/10.1016/S1365-1609(02)00032-1
  52. Zhang, D., Hou, S., Bian, J. and He, L. (2016), "Investigation of the micro-cracking behavior of asphalt mixtures in the indirect tensile test", Eng. Fract. Mech., 163, 416-425. https://doi.org/10.1016/j.engfracmech.2016.05.020.
  53. Zheng, W., Kwan, A.K.H. and Lee, P.K.K. (2001), "Direct tension test of concrete", ACI Mater. J., 98(1) 63-71.
  54. Zhou, F.P. (1988), "Some aspects of tensile fracture behaviour and structural response of cementitious materials", Report TVBM-1008, Lund Institute of Technology, Lund, Sweden.
  55. Zhou, X.P. and Yang, H.Q. (2012), "Multiscale numerical modeling of propagation and coalescence of multiple cracks in rock masses", Int. J. Rock Mech. Min. Sci., 55, 15-27. https://doi.org/10.1016/j.ijrmms.2012.06.001.
  56. Zhou, X.P. and Wang, Y. (2016), "Numerical simulation of crack propagation and coalescence in pre-cracked rock-like Brazilian disks using the non-ordinary state-based peridynamics", Int. J. Rock Mech. Min. Sci., 89, 235-249. https://doi.org/10.1016/j.ijrmms.2016.09.010.
  57. Zhou, X.P., Zhang, Y.X., Ha, Q.L. and Zhu, K.S. (2008), "Micromechanical modelling of the complete stress-strain relationship for crack weakened rock subjected to compressive loading", Rock Mech. Rock Eng., 41(5), 747-769. https://doi.org/10.1007/s00603-007-0130-2.
  58. Zhou, X.P., Bi, J. and Qian, Q. (2015), "Numerical simulation of crack growth and coalescence in rock-like materials containing multiple pre-existing flaws", Rock Mech. Rock Eng., 48(3), 1097-1114. https://doi.org/10.1007/s00603-014-0627-4.