DOI QR코드

DOI QR Code

Experimental study on seismic behavior of two-storey modular structure

  • Liu, Yang (State Key Laboratory of Hydraulic Engineering Simulation and Safety, Tianjin University) ;
  • Chen, Zhihua (State Key Laboratory of Hydraulic Engineering Simulation and Safety, Tianjin University) ;
  • Liu, Jiadi (Department of Civil Engineering, Tianjin University) ;
  • Zhong, Xu (Department of Civil Engineering, Tianjin University)
  • 투고 : 2019.10.29
  • 심사 : 2020.10.20
  • 발행 : 2020.11.10

초록

Due to the unique construction method of modular steel buildings (MSBs) with units prefabricated fully off the site and assembled quickly on the site, the inter-module connection for easy operation and overall performance of the system were key issues. However, it was a lack of relevant research on the system-level performance of MSBs. This study investigated the seismic performance of two-storey modular steel structure with a proposed vertical rotary inter-module connection. Three full-scale quasi-static tests, with and without corrugated steel plate and its combination, were carried out to evaluate and compare their seismic behaviour. The hysteretic performance, skeleton curves, ductile performance, stiffness degradation, energy dissipation capacity, and deformation pattern were clarified. The results showed that good ductility and plastic deformation ability of such modular steel structures. Two lateral-force resistance mechanisms with different layout combinations were also discussed in detail. The corrugated steel plate could significantly improve the lateral stiffness and bearing capacity of the modular steel structure. The cooperative working mechanism of modules and inter-module connections was further analyzed. When the lateral stiffness of upper and lower modular structures was close, limited bending moment transfer may be considered for the inter-module connection. While a large lateral stiffness difference existed initially between the upper and lower structures, an obvious gap occurred at the inter-module connection, and this gap may significantly influence the bending moments transferred by the inter-module connections. Meanwhile, several design recommendations of inter-module connections were also given for the application of MSBs.

키워드

과제정보

This research was sponsored by the Science and Technology Project of Tianjin (Grant No. 17ZXCXSF00050) and the National Key Research and Development Program of China (Grant no. 2017YFC0703803).

참고문헌

  1. AISC 341-16 (2016), Seismic Provisions for Structural Steel Buildings, American Institute of Steel Construction, Chicago, USA.
  2. Annan, C.D., Youssef, M.A. and El Naggar, M.H. (2009), "Seismic vulnerability assessment of modular steel buildings", J. Earthq. Eng., 13(8) ,1065-1088. https://doi.org/10.1080/13632460902933881.
  3. ATC-24 (1992), Guidelines for Cyclic Seismic Testing of Components of Steel Structures, Applied Technology Council, Redwood City, CA, USA.
  4. Chen, Z.H., Li, H.X., Chen, A.Y., Yu, Y.J. and Wang, H. (2017), "Research on pretensioned modular frame test and simulations", Eng. Struct., 151, 774-787. https://doi.org/10.1016/j.engstruct.2017.08.019.
  5. Chen, Z.H., Liu, J.D. and Yu, Y.J. (2017), "Experimental study on interior connections in modular steel buildings", Eng. Struct., 147, 625-638. https://doi.org/10.1016/j.engstruct.2017.06.002.
  6. Chen, Z.H., Liu, Y., Zhong, X. and Liu, J.D. (2019), "Rotational stiffness of inter-module connection in mid-rise modular steel buildings", Eng. Struct., 196, 109273. https://doi.org/10.1016/j. engstruct.2019.06.009.
  7. Cho, B.H., Lee, JS., Kim, H.J. and Kim, D.J. (2019), "Structural Performance of a New Blind-Bolted Frame Modular Beam-Column Connection under Lateral Loading", Appl. Sci., 9(9), 1929. https://doi.org/10.3390/app9091929.
  8. Dai, X.M., Zong, L., Ding, Y. and Li, Z.X. (2019), "Experimental study on seismic behavior of a novel plug-in self-lock joint for modular steel construction", Eng. Struct., 181, 143-164. https://doi.org/10.1016/j.engstruct.2018.11.075.
  9. Dai, Z.Q., Dai Pang, S. and Richard Liew, J.Y. (2020), "Axial load resistance of grouted sleeve connection for modular construction", Thin-Wall. Struct., 154, 106883. https://doi.org/10.1016/j.tws.2020.106883.
  10. Deng, E.F., Zong, L. and Ding, Y. (2019), "Numerical and analytical study on initial stiffness of corrugated steel plate shear walls in modular construction", Steel Compos. Struct., 32(3), 347-359. https://doi.org/10.12989/scs.2019.32.3.347.
  11. Deng, E.F., Zong, L., Ding, Y., Dai, X.M., Lou, N. and Chen, Y. (2018), "Monotonic and cyclic response of bolted connections with welded cover plate for modular steel construction", Eng. Struct., 167, 407-419. https://doi.org/10.1016/j.engstruct.2018.04.028.
  12. Ding, C.T., Bai, Y., Qiu, C.Y., Wan, C.Q. and Zhao, X.L. (2020), "Steel bolted flanged connections in tension: Effects of stiffener configurations", Thin-Wall. Struct., 154, 106824. https://doi.org/10.1016/j.tws.2020.106824.
  13. Ding, Y., Deng, E.F., Zong, L., Dai, X.M., Lou, N. and Chen, Y. (2017), "Cyclic tests on corrugated steel plate shear walls with openings in modularized-constructions", J. Constr. Steel Res., 138, 675-691. https://doi.org/10.1016/j.jcsr.2017.08.019.
  14. Ferdous, W., Bai, Y., Ngo, T.D., Manalo, A. and Mendis, P. (2019), "New advancements, challenges and opportunities of multi-storey modular buildings -A state-of-the-art review", Eng. Struct., 183, 883-893. https://doi.org/10.1016/j.engstruct.2019.01.061.
  15. GB 50011-2016 (2016), Code for Seismic Design of Buildings; China Ministry of Construction, Beijing, China.
  16. Gibb, A.G.F. (1999), "Offsite Fabrication: Prefabrication, Pre-assembly and Modularisation", Whittles Publishing, Scotland, UK.
  17. Innella, F., Arashpour, M. and Bai, Y. (2019), "Lean Methodologies and Techniques for Modular Construction: Chronological and Critical Review", J. Constr. Eng. Manage., 145(12), 04019076. https://doi.org/10.1061/(ASCE)CO.1943-7862.0001712.
  18. Innella, F., Bai, Y. and Zhu, Z.H. (2020), "Acceleration responses of building modules during road transportation", Eng. Struct., 210, 110398. https://doi.org/10.1016/j.engstruct.2020.110398.
  19. Khan, K. and Yan, J.B. (2020), "Finite element analysis on seismic behaviour of novel joint in prefabricated modular steel building", Int. J. Steel Struct., 20(3), 752-765. https://doi.org/10.1007/s13296-020-00320-w.
  20. Lacey, A.W., Chen, W.S., Hao H. and Bi, K.M. (2019), "Review of bolted inter-module connections in modular steel buildings", J. Build. Eng., 23, 207-219. https://doi.org/10.1016/j.jobe.2019.01.035.
  21. Lawson, R.M., Byfield, M.P., Popo-Ola, S.O. and Grubb, P.J. (2008), "Robustness of light steel frames and modular construction", Proc. Inst. Civ. Eng. Struct. Build., 161, 3-16. https://doi.org/10.1680/stbu.2008.161.1.3.
  22. Lawson, R.M., Ogden, R.G. and Goodier, C. (2014), "Design in Modular Construction", CRC Press, Boca Raton, FL, USA.
  23. Lawson, R.M., Ogden, R.G. and Bergin, R. (2012), "Application of modular construction in high-rise buildings", J. Archit. Eng. 18(2), 148-154. https://doi.org/10.1061/(ASCE)AE.1943-5568.0000057.
  24. Lawson, R.M. and Richards, J. (2010), "Modular design for high-rise buildings", Proc. Inst. Civ. Eng. Struct. Build., 163(3), 151-164. https://doi.org/10.1680/stbu.2010.163.3.151.
  25. Lee, S., Park, J., Shon, S. and Kang, C. (2018), "Seismic performance evaluation of the ceiling-bracket-type modular joint with various bracket parameters", J. Constr. Steel Res., 150, 298-325. https://doi.org/10.1016/j.jcsr.2018.08.008.
  26. Liu, Y, Chen, Z.H., Liu, J.D., Bai, Y., Zhong, X. and Wang, X.D. (2020), "Lateral stiffness evaluation on corner-supported thin walled modular steel structures", Thin-Wall. Struct., 157, 106967. https://doi.org/10.1016/j.tws.2020.106967.
  27. Luo, F. J., Ding, C.T., Styles, A. and Bai Y. (2019), "End Plate-Stiffener Connection for SHS Column and RHS Beam in Steel-Framed Building Modules", Int. J. Steel Struct., 19(4), 1353-1365. https://doi.org/10.1007/s13296-019-00214-6.
  28. Sanches, R., Mercan, O. and Roberts, B. (2018), "Experimental investigations of vertical post-tensioned connection for modular steel structures", Eng. Struct., 175, 776-789. https://doi.org/10.1016/j.engstruct.2018.08.049.
  29. Sharafi, P., Samali, B., Ronagh, H. and Ghodrat, M. (2017), "Automated spatial design of multi-story modular buildings using a unified matrix method", Automat. Constr., 82, 31-42. https://doi.org/10.1016/j.autcon.2017.06.025.
  30. Shi, F.W., Wang, H.P., Zong, L., Ding, Y. and Su, J.S. (2020), "Seismic behavior of high-rise modular steel constructions with various module layouts", J. Build Eng., 31, 101396. https://doi.org/10.1016/j.jobe.2020.101396.
  31. Styles, A.J., Luo, F.J., Bai, Y. and Murray-Parkes, J.B. (2016), "Effects of joint rotational stiffness on structural responses of multi-story modular buildings", Proceedings of the 2016 International Conference on Smart Infrastructure and Construction, ICSIC.
  32. Xu, B. Xia, J.W., Chang, H.F., Ma, R.W. and Zhang, L.H. (2020), "Flexural behaviour of pairs of laminated unequal channel beams with different interfacial connections in corner-supported modular steel buildings", Thin-Wall. Struct., 154, 106792. https://doi.org/10.1016/j.tws.2020.106792.
  33. Yu, Y.J., Chen, Z.H. and Chen, A.Y. (2019), "Experimental study of a pretensioned connection for modular buildings", Steel Compos. Struct., 31(3), 217-232. https://doi.org/10.12989/scs.2019.31.3.217.
  34. Zuo, Y. and Zha, X.X. (2017), "FEM and experimental study on mechanical property of container building with holes", Int. J. Steel Struct., 17(1), 175-194. https://doi.org/10.1007/s13296-015-0132-y.