Wind and Structures

  • 제31권2호
  • /
  • Pages.103-142
  • /
  • 2020
  • /
  • 1226-6116(pISSN)
  • /
  • 1598-6225(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Performance-based wind design of tall buildings: concepts, frameworks, and opportunities

  • Bezabeh, Matiyas A. (Department of Civil and Environmental Engineering, Western University) ;
  • Bitsuamlak, Girma T. (Department of Civil and Environmental Engineering, Western University) ;
  • Tesfamariam, Solomon (School of Engineering, University of British Columbia)
  • 투고 : 2019.09.29
  • 심사 : 2020.03.04
  • 발행 : 2020.08.25
⟨ 이전 논문 다음 논문 ⟩

초록

One of the next frontiers in structural wind engineering is the design of tall buildings using performance-based approaches. Currently, tall buildings are being designed using provisions in the building codes and standards to meet an acceptable level of public safety and serviceability. However, recent studies in wind and earthquake engineering have highlighted the conceptual and practical limitations of the code-oriented design methods. Performance-based wind design (PBWD) is the logical extension of the current wind design approaches to overcome these limitations. Towards the development of PBWD, in this paper, we systematically review the advances made in this field, highlight the research gaps, and provide a basis for future research. Initially, the anatomy of the Wind Loading Chain is presented, in which emphasis was given to the early works of Alan G. Davenport. Next, the current state of practice to design tall buildings for wind load is presented, and its limitations are highlighted. Following this, we critically review the state of development of PBWD. Our review on PBWD covers the existing design frameworks and studies conducted on the nonlinear response of structures under wind loads. Thereafter, to provide a basis for future research, the nonlinear response of simple yielding systems under long-duration turbulent wind loads is studied in two phases. The first phase investigates the issue of damage accumulation in conventional structural systems characterized by elastic-plastic, bilinear, pinching, degrading, and deteriorating hysteretic models. The second phase introduces methods to develop new performance objectives for PBWD based on joint peak and residual deformation demands. In this context, the utility of multi-variate demand modeling using copulas and kernel density estimation techniques is presented. This paper also presents joined fragility curves based on the results of incremental dynamic analysis. Subsequently, the efficiency of tuned mass dampers and self-centering systems in controlling the accumulation of damage in wind-excited structural systems are investigated. The role and the need for explicit modeling of uncertainties in PBWD are also discussed with a case study example. Lastly, two unified PBWD frameworks are proposed by adapting and revisiting the Wind Loading Chain. This paper concludes with a summary and a proposal for future research.

키워드

참고문헌

  1. Abdi, D.S. and Bitsuamlak, G.T. (2014), "Wind flow simulations on idealized and real complex terrain using various turbulence models", Advan. Eng. Softw., 75, 30-41. https://doi.org/10.1016/j.advengsoft.2014.05.002.
  2. AIJ (Architectural Institute of Japan) (2004), Recommendations for Wind Loads on Buildings, AIJ, Tokyo, Japan.
  3. Aiken, I.D., Nims, D.K., Whittaker A.S. and Kelly, J.M. (1993), "Testing of passive energy dissipation systems" Earthq. Spectra, 9(3), 335-370. https://doi.org/10.1193%2F1.1585720. https://doi.org/10.1193/1.1585720
  4. Alam, M.S., Nehdi, M. and Youssef, M.A. (2009), "Seismic performance of concrete frame structures reinforced with superelastic shape memory alloys", Smart Struct. Syst., 5(5), 565-585. https://doi.org/10.12989/sss.2009.5.5.565
  5. ASCE 41-06 (2006), Seismic rehabilitation of existing buildings, ASCE, Reston, VA, U.S.A.
  6. ASCE/SEI (ASCE/Structural Engineering Institute) (2019), Pre-standard for Performance-Based Wind Design, American Society of Civil Engineers, Reston, VA, U.S.A.
  7. ASCE/SEI 7-16 (2016), Minimum design loads for buildings and other structures, ASCE/Structural Engineering Institute, Reston, VA, USA.
  8. Aschheim, M. (2002), "Seismic design based on the yield displacement", Earthq. spectra, 18(4), 581-600. https://doi.org/10.1193%2F1.1516754. https://doi.org/10.1193/1.1516754
  9. Aschheim, M., Hernandez-Montes, E. and Vamvatsikos, D. (2019), Design of Reinforced Concrete Buildings for Seismic Performance: Practical Deterministic and Probabilistic Approaches, CRC Press.
  10. ATC (1978), Tentative provisions for the development of seismic regulations for buildings, No. ATC 3-06, Applied Technology Council, Palo Alto, U.S.A.
  11. ATC (1996), Seismic evaluation and retrofit of existing concrete buildings, No. ATC-40, Applied Technology Council, Redwood City, U.S.A.
  12. Baker, J.W. (2015), "Efficient analytical fragility function fitting using dynamic structural analysis", Earthq. Spectra, 31(1), 579-599. https://doi.org/10.1193/021113EQS025M
  13. Banik, S.S., Hong, H.P. and Kopp, G.A. (2010), "Assessment of capacity curves for transmission line towers under wind loading", Wind and Structures, 13(1), 1-20. https://doi.org/10.12989/was.2010.13.1.001
  14. Barbato, M., Petrini, F., Unnikrishnan, V.U. and Ciampoli, M. (2013), "Performance-based hurricane engineering (PBHE) framework", Struct. Safety, 45, 24-35. https://doi.org/10.1016/j.strusafe.2013.07.002.
  15. Bernardini, E., Spence, S.M., Kwon, D.K. and Kareem, A. (2014), "Performance-based design of high-rise buildings for occupant comfort", J. Struct. Eng., 141(10), 04014244. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001223.
  16. Bertero, R.D. and Bertero, V.V. (2002), "Performance-based seismic engineering: the need for a reliable conceptual comprehensive approach", Earthq. Eng. Struct. Dyn., 31(3), 627-652. https://doi.org/10.1002/eqe.146.
  17. Bezabeh, M.A., Bitsuamlak G. and Tesfamariam, S. (2019a), "The first step towards the performance-based design of wind-excited buildings: A critical examination of ductility demand, hysteretic energy, and control of damage accumulation", 15th International Conference on Wind Engineering (ICWE-15), Beijing, China.
  18. Bezabeh, M.A., Bitsuamlak G. and Tesfamariam, S. (2019b), "Controlling hurricane-induced structural damage by tuned mass dampers and self-centering structural systems", 15th International Conference on Wind Engineering (ICWE-15), Beijing, China.
  19. Bezabeh, M.A., Bitsuamlak G. and Tesfamariam, S. (2019c), "Performance-based wind design of tall buildings with explicit consideration of damage accumulation", 10th World Congress (CTBUH 2019), Chicago, USA.
  20. Bezabeh, M.A., Bitsuamlak G. and Tesfamariam, S. (2019d), "Should we consider the plastic capacity of structural systems in the design of wind-excited buildings? A critical examination of damage accumulation, ductility demand, and hysteretic energy", CSCE Annual Conference - Laval (Greater Montreal), Canada.
  21. Bezabeh, M.A., Bitsuamlak, G.T., Popovski, M. and Tesfamariam, S. (2018a), "Probabilistic serviceability-performance assessment of tall mass-timber buildings subjected to stochastic wind loads: part I-structural design and wind tunnel testing", J. Wind Eng. Ind. Aerod., 181, 85-103. https://doi.org/10.1016/j.jweia.2018.08.012.
  22. Bezabeh, M.A., Bitsuamlak, G.T., Popovski, M. and Tesfamariam, S. (2018b), "Probabilistic serviceability-performance assessment of tall mass-timber buildings subjected to stochastic wind loads: part II-structural reliability analysis", J. Wind Eng. Ind. Aerod., 181, 112-125. https://doi.org/10.1016/j.jweia.2018.08.012.
  23. Bezabeh, M.A., Tesfamariam, S., Popovski, M., Goda, K. and Stiemer, S.F. (2017), "Seismic base shear modification factors for timber-steel hybrid structure: collapse risk assessment approach", J. Struct. Eng., 143(10), 04017136. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001869.
  24. Bezabeh, M.A., Tesfamariam, S., Stiemer, S.F., Popovski, M. and Karacabeyli, E. (2016), "Direct displacement-based design of a novel hybrid structure: steel moment-resisting frames with cross-laminated timber infill walls", Earthq. Spectra, 32(3), 1565-1585. https://doi.org/10.1193%2F101514EQS159M. https://doi.org/10.1193/101514EQS159M
  25. Bitsuamlak, G.T., Stathopoulos, T. and Bedard, C. (2004), "Numerical evaluation of wind flow over complex terrain", J. Aerosp. Eng., 17(4), 135-145. https://doi.org/10.1061/(ASCE)0893-1321(2004)17:4(135).
  26. Blocken, B. (2014), "50 years of computational wind engineering: past, present and future", J. Wind Eng. Ind. Aerod., 129, 69-102. https://doi.org/10.1016/j.jweia.2014.03.008.
  27. Blume, J.A., Newmark, N.M. and Corning, L.H. (1961), Design of Multistory Reinforced Concrete Buildings for Earthquake Motions, Chicago: Portland Cement Association, U.S.A.
  28. Boggs, D.W. and Peterka, J.A. (1989), "Aerodynamic model tests of tall buildings", J. Eng. Mech., 115(3), 618-635. https://doi.org/10.1061/(ASCE)0733-9399(1989)115:3(618).
  29. Botev, Z.I., Grotowski, J.F. and Kroese, D.P. (2010), "Kernel density estimation via diffusion", Annal. Statistics, 38(5), 2916-2957. https://doi.org/10.1214/10-AOS799
  30. Bouye, E., Durrleman, V., Nikeghbali, A., Riboulet, G. and Roncalli, T. (2000), "Copulas for finance - a reading guide and some applications", SSRN 1032533. https://dx.doi.org/10.2139/ssrn.1032533.
  31. Caracoglia, L. (2018), "Unified stochastic dynamic and damage cost model for the structural analysis of tall buildings in thunderstorm-like winds", ASCE-ASME J. Uncertain. Eng. Syst, Part A: Civil Eng., 4(4), 04018043. https://doi.org/10.1061/AJRUA6.0000999.
  32. Cermak, J.E. (1975), "Applications of fluid mechanics to wind engineering-a Freeman Scholar lecture", J. Fluids Eng., 97(1), 9-38. https://doi.org/10.1115/1.3447225
  33. Cermak, J.E. (1977), "Wind-tunnel testing of structures", J. Eng. Mech. Div., 103(6), 1125-1140. https://doi.org/10.1061/JMCEA3.0002301
  34. Cermak, J.E. (2003), "Wind-tunnel development and trends in applications to civil engineering", J. Wind Eng. Ind. Aerod., 91(3), 355-370. https://doi.org/10.1016/S0167-6105(02)00396-3.
  35. Chancellor, N., Eatherton, M., Roke, D. and Akbas, T. (2014), "Self-centering seismic lateral force resisting systems: high performance structures for the city of tomorrow", Build., 4(3), 520-548. https://doi.org/10.3390/buildings4030520.
  36. Chen, D. and Davenport, A.G. (2000), "Vulnerability of tall buildings in typhoons", Advan. Struct. Dyn., 2, 1455-1462.
  37. Chen, X. and Kareem, A. (2005), "Coupled dynamic analysis and equivalent static wind loads on buildings with three-dimensional modes", J. Struct. Eng., 131(7), 1071-1082. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:7(1071).
  38. Chopra, A.K. (2000), Dynamics of Structures, Prentice Hall, New Jersey, U.S.A.
  39. Christidis, A.A., Dimitroudi, E.G., Hatzigeorgiou, G.D. and Beskos, D.E. (2013) "Maximum seismic displacements evaluation of steel frames from their post-earthquake residual deformation", Bull. Earthq. Eng., 11(6), 2233-2248. https://doi.org/10.1007/s10518-013-9490-z.
  40. Christopoulos, C. and Pampanin, S. (2004), "Towards performance-based design of MDOF structures with explicit consideration of residual deformations", SET J. Earthq. Technol., 41(1), 53-73
  41. Christopoulos, C., Filiatrault, A. and Folz, B. (2002), "Seismic response of self-centring hysteretic SDOF systems", Earthq. Eng. Struct. Dyn., 31(5), 1131-1150. https://doi.org/10.1002/eqe.152.
  42. Christopoulos, C., Pampanin, S. and Nigel Priestley, M.J. (2003), "Performance-based seismic response of frame structures including residual deformations part I: single-degree of freedom systems", J. Earthq. Eng., 7(01), 97-118.
  43. Christopoulos, C., Tremblay, R., Kim, H.J. and Lacerte, M. (2008), "Self-centering energy dissipative bracing system for the seismic resistance of structures: development and validation", J. Struct. Eng., 134(1), 96-107. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:1(96).
  44. Chryssanthopoulos, M.K., Dymiotis, C. and Kappos, A.J. (2000), "Probabilistic evaluation of behaviour factors in EC8-designed R/C frames", Eng. Struct., 22(8), 1028-1041. https://doi.org/10.1016/S0141-0296(99)00026-7.
  45. Chuang, W.C. and Spence, S.M. (2017), "A performance-based design framework for the integrated collapse and non-collapse assessment of wind excited buildings," Eng. Struct., 150, 746-758. https://doi.org/10.1016/j.engstruct.2017.07.030.
  46. Chuang, W.C. and Spence, S.M. (2019), "An efficient framework for the inelastic performance assessment of structural systems subject to stochastic wind loads", Eng. Struct., 179, 92-105. https://doi.org/10.1016/j.engstruct.2018.10.039.
  47. Ciampoli, M. and Petrini, F. (2012), "Performance-based Aeolian risk assessment and reduction for tall buildings", Probab. Eng. Mech., 28, 75-84. https://doi.org/10.1016/j.probengmech.2011.08.013.
  48. Ciampoli, M., Petrini, F. and Augusti, G. (2011), "Performance-based wind engineering: towards a general procedure", Struct. Safety, 33(6), 367-378. https://doi.org/10.1016/j.strusafe.2011.07.001.
  49. CNR-DT 207/2008 (2010), Guide for the Assessment of Wind Actions and Effects on Structures, National Research Council, Rome, Italy.
  50. Connolly, T., Loss, C., Iqbal, A. and Tannert, T. (2018), "Feasibility study of mass-timber cores for the UBC tall wood building", Build., 8(8), 98. https://doi.org/10.3390/buildings8080098.
  51. Cornell, C.A. and Krawinkler, H. (2000), "Progress and challenges in seismic performance assessment", PEER Center News, 3(2), 1-3.
  52. Costa, A., Romao, X. and Oliveira, C.S. (2010), "A methodology for the probabilistic assessment of behaviour factors", Bull. Earthq. Eng., 8(1), 47. https://doi.org/10.1007/s10518-009-9126-5.
  53. Cui, W. and Caracoglia, L. (2015), "Simulation and analysis of intervention costs due to wind-induced damage on tall buildings", Eng. Struct., 87, 183-197. https://doi.org/10.1016/j.engstruct.2015.01.001.
  54. Cui, W. and Caracoglia, L. (2018), "A unified framework for performance-based wind engineering of tall buildings in hurricane-prone regions based on lifetime intervention-cost estimation", Struct. Safety, 73, 75-86. https://doi.org/10.1016/j.strusafe.2018.02.003.
  55. Cui, W. and Caracoglia, L. (2020), "Performance-based wind engineering of tall buildings examining life-cycle downtime and multisource wind damage", J. Struct. Eng., 146(1), 04019179. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002479.
  56. Dagnew, A.K. and Bitsuamlak, G.T. (2013), "Computational evaluation of wind loads on buildings: a review", Wind Struct., 16(6), 629-660. http://dx.doi.org/10.12989/was.2013.16.6.629.
  57. Dagnew, A.K. and Bitsuamlak, G.T. (2014), "Computational evaluation of wind loads on a standard tall building using LES", Wind Struct., 18(5), 567-598. http://dx.doi.org/10.12989/was.2014.18.5.567.
  58. Davenport A.G. (1970), "Wind loading on tall buildings", Symposium on Wind Effects on High Rise Buildings, Evanston, U.S.A.
  59. Davenport, A.G. (1961), "The spectrum of horizontal gustiness near the ground in high winds", Quart. J. Royal Meteorol. Soc., 87(372), 194-211. https://doi.org/10.1002/qj.49708737208.
  60. Davenport, A.G. (1963), "The relationship of wind structure to wind loading, paper 2", Proceedings of the Symposium on Wind Effects on Buildings and Structures, NPL, U.K.
  61. Davenport, A.G. (1964), "Note on the distribution of the largest value of a random function with application to gust loading", Proc. Institu. Civil Eng., 28(2), 187-196. https://doi.org/10.1680/iicep.1964.10112.
  62. Davenport, A.G. (1965), "The relationship of wind structure to wind loading", Proceedings of the Conference on Wind Effects on Buildings & Structures, Teddington, U.K.
  63. Davenport, A.G. (1967), "Gust loading factors", J. Struct. Div., 93(3), 11-34. https://doi.org/10.1061/JSDEAG.0001692
  64. Davenport, A.G. (1968), "The dependence of wind loads on meteorological parameter", Wind Effects Build. Struct., 19-82.
  65. Davenport, A.G. (1971), "On the statistical prediction of structural performance in the wind environment", ASCE National Struct. Meeting, Baltimore, U.S.A.
  66. Davenport, A.G. (1972), "Structural Safety and reliability under wind action", International Conference on Structural Safety and Reliability, Washington, D.C., U.S.A, April.
  67. Davenport, A.G. (1975), "Tall buildings - An anatomy of wind risks", Construction in South Africa, December.
  68. Davenport, A.G. (1977), "The prediction of risk under wind loading", Proceedings of the 2nd International Conference on Structural Safety and Reliability, Munich, Germany.
  69. Davenport, A.G. (1983), "The relationship of reliability to wind loading", J. Wind Eng. Ind. Aerod., 13(1-3), 3-27. https://doi.org/10.1016/0167-6105(83)90125-3.
  70. Davenport, A.G. and Hill-Carroll, P. (1986), "Damping in tall buildings: its variability and treatment in design", Building Motion in Wind, Seattle, U.S.A, April.
  71. Davenport, A.G. and Isyumov, N. (1967), "The application of the boundary layer wind tunnel to the prediction of wind loading", In Proceedings of the International Research Seminar: Wind Effects on Buildings and Structures, Ottawa, Canada. September.
  72. Deaves, D.M. (1981), "Computations of wind flow over changes in surface roughness", J. Wind Eng. Ind. Aerod., 7(1), 65-94. https://doi.org/10.1016/0167-6105(81)90068-4.
  73. Deaves, D.M. and Harris, R.I. (1978), A Mathematical Model of the Structure of Strong Winds, Report No. 76, Construction Industry Research and Information Association, London, U.K.
  74. DesRoches, R., McCormick, J. and Delemont, M. (2004), "Cyclic properties of superelastic shape memory alloy wires and bars", J. Struct. Eng., 130(1), 38-46. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:1(38).
  75. Dickof, C., Stiemer, S.F., Bezabeh, M.A. and Tesfamariam, S. (2014), "CLT-steel hybrid system: ductility and overstrength values based on static pushover analysis", J. Perform. Construct. Facilit., 28(6), A4014012. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000614.
  76. Diniz, S.M. and Simiu, E. (2005), "Probabilistic descriptions of wind effects and wind-load factors for database-assisted design", J. Struct. Eng., 131(3), 507-516. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:3(507).
  77. Dolce, M. and Cardone, D. (2006), "Theoretical and experimental studies for the application of shape memory alloys in civil engineering", J. Eng. Mater. Technol., 128, 302-311. https://doi.org/10.1115/1.2203106.
  78. Dolce, M., Cardone, D. and Marnetto, R. (2000), "Implementation and testing of passive control devices based on shape memory alloys", Earthq. Eng. Struct. Dyn., 29(7), 945-968. https://doi.org/10.1002/1096-9845(200007)29:7%3C945::AID-EQE958%3E3.0.CO;2-%23.
  79. duPlessis, D.P. and Daniels, J.H. (1971), "Performance design of tall buildings for wind", Report No.376.1; Lehigh University, Bethlehem, U.S.A.
  80. Eatherton, M.R. and Hajjar, J.F. (2011), "Residual drifts of self-centering systems including effects of ambient building resistance", Earthq. Spectra, 27(3), 719-744. https://doi.org/10.1193/1.3605318
  81. Elezaby, F.Y. (2017), "A performance based design approach for tall buildings under wind loading", Masters thesis, Western University, Canada.
  82. Ellingwood, B. (1998), "Reliability-based performance concept for building construction", Proceedings of the Structural Engineers World Congress, San Francisco, California, U.S.A.
  83. Ellingwood, B., Galambos, T.V., MacGregor, J.G. and Cornell, C.A. (1980), Development of a Probability-based Load Criterion for American National Standard A58: Building Code Requirements for Minimum Design Loads in Buildings and Other Structures, U.S. Department of Commerce, National Bureau of Standards, U.S.A.
  84. Ellingwood, B.R. and Tekie, P.B. (1999), "Wind load statistics for probability-based structural design", J. Struct. Eng., 125(4), 453-463. https://doi.org/10.1061/(ASCE)0733-9445(1999)125:4(453).
  85. Ellingwood, B.R. and Wen, Y.K. (2005), "Risk-benefit-based design decisions for low-probability/high consequence earthquake events in Mid-America", Progr. Struct. Eng. Mater., 7(2), 56-70. https://doi.org/10.1002/pse.191.
  86. Elshaer, A. and Bitsuamlak, G. (2018), "Multiobjective aerodynamic optimization of tall building openings for wind-induced load reduction", J. Struct. Eng., 144(10), 04018198. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002199.
  87. Elshaer, A., Bitsuamlak, G. and El Damatty, A. (2017), "Enhancing wind performance of tall buildings using corner aerodynamic optimization", Eng. Struct., 136, 133-148. https://doi.org/10.1016/j.engstruct.2017.01.019.
  88. Erochko, J., Christopoulos, C., Tremblay, R. and Choi, H. (2010), "Residual drift response of SMRFs and BRB frames in steel buildings designed according to ASCE 7-05", J. Struct. Eng., 137(5), 589-599. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000296.
  89. ESDU 74031 (1974), Characteristics of atmospheric turbulence near the ground, Engineering Sciences Data Unit, U.K.
  90. Fajfar, P. (1999), "Capacity spectrum method based on inelastic demand spectra", Earthq. Eng. Struct. Dyn., 28(9), 979-993. https://doi.org/10.1002/(SICI)10969845(199909)28:9%3C979::AID-EQE850%3E3.0.CO;2-1.
  91. Fardis, M.N. (2018), "Capacity design: early history", Earthq. Eng. Struct. Dyn., 47(14), 2887-2896. https://doi.org/10.1002/eqe.3110.
  92. FEMA 273 (1997a), NEHRP guidelines for the seismic rehabilitation of buildings, Federal Emergency Management Agency; Washington, D.C., U.S.A.
  93. FEMA 274 (1997b), NEHRP guidelines for the seismic rehabilitation of buildings, Federal Emergency Management Agency; Washington, D.C., U.S.A.
  94. FEMA 356 (2000), Pre-standard and commentary for seismic rehabilitation of buildings, Federal Emergency Management Agency; Washington, D.C., U.S.A.
  95. FEMA P-58-2 (2012), Seismic performance assessment of buildings, Volume 2 - Implementation, Applied Technology Council for the Federal Emergency Management Agency, Washington, D.C., U.S.A.
  96. FEMA P695 (2009), Quantification of building seismic performance factors, Applied Technology Council, Redwood City, U.S.A.
  97. Feng, C. and Chen, X. (2017), "Crosswind response of tall buildings with nonlinear aerodynamic damping and hysteretic restoring force character", J. Wind Eng. Ind. Aerod., 167, 62-74. https://doi.org/10.1016/j.jweia.2017.04.012.
  98. Feng, C. and Chen, X. (2018), "Inelastic responses of wind-excited tall buildings: Improved estimation and understanding by statistical linearization approaches", Eng. Struct., 159, 141-154. https://doi.org/10.1016/j.engstruct.2017.12.041.
  99. Filiatrault, A., Restrepo, J. and Christopoulos, C. (2004), "Development of self-centering earthquake resisting systems", The 13th World Conference on Earthquake Engineering, Vancouver, Canada.
  100. Foliente, G.C. (1995), "Hysteresis modeling of wood joints and structural systems", J. Struct. Eng., 121(6), 1013-1022. https://doi.org/10.1061/(ASCE)0733-9445(1995)121:6(1013).
  101. Franchin, P., Petrini, F. and Mollaioli, F. (2018), "Improved risk-targeted performance-based seismic design of reinforced concrete frame structures", Earthq. Eng. Struct. Dyn., 47(1), 49-67. https://doi.org/10.1002/eqe.2936.
  102. Fujino, Y. and Abe, M. (1993), "Design formulas for tuned mass dampers based on a perturbation technique", Earthq. Eng. Struct. Dyn., 22(10), 833-854. https://doi.org/10.1002/eqe.4290221002.
  103. Gairola, A. and Bitsuamlak, G. (2019), "Numerical tornado modeling for common interpretation of experimental simulators", J. Wind Eng. Ind. Aerod., 186, 32-48. https://doi.org/10.1016/j.jweia.2018.12.013.
  104. Ganey, R., Berman, J., Akbas, T., Loftus, S., Daniel Dolan, J., Sause, R., Ricles, J., Pei, S., van de Lindt, J. and Blomgren, H.E. (2017), "Experimental investigation of self-centering cross-laminated timber walls", J. Struct. Eng., 143(10), 04017135. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001877.
  105. Gani, F. and Legeron, F. (2012), "Relationship between specified ductility and strength demand reduction for single degree-of-freedom systems under extreme wind events", J. Wind Eng. Ind. Aerod., 109, 31-45. https://doi.org/10.1016/j.jweia.2012.06.006.
  106. Georgiou, P.N., Vickery, B.J. and Surry, D. (1988), "The effect of non-linear structural behavior on wind-induced plastic damage of low-rise buildings", J. Wind Eng. Ind. Aerod., 29(1), 235-244. https://doi.org/10.1016/0167-6105(88)90161-4.
  107. Ghobarah, A. (2001), "Performance-based design in earthquake engineering: state of development", Eng. Struct., 23(8), 878-884. https://doi.org/10.1016/S0141-0296(01)00036-0.
  108. Glogau, O.A. (1976), "Code philosophy", Bull. New Zealand National Soc. Earthq. Eng., 9(1), 43-55. https://doi.org/10.5459/bnzsee.9.1.43-55
  109. Goda, K. and Hong, H.P. (2010), "Effectiveness of tuned mass dampers for reducing wind-induced plastic deformation", The 9th UK Conference on Wind Engineering, Bristol, U.K.
  110. Goda, K. and Tesfamariam, S. (2015), "Multi-variate seismic demand modelling using copulas: Application to non-ductile reinforced concrete frame in Victoria, Canada", Struct. Safety, 56, 39-51. https://doi.org/10.1016/j.strusafe.2015.05.004.
  111. Gomes, L. and Vickery, B.J. (1977), "On the prediction of extreme wind speeds from the parent distribution", J. Wind Eng. Ind. Aerod., 2(1), 21-36. https://doi.org/10.1016/0167-6105(77)90003-4.
  112. Griffis, L., Patel, V., Muthukumar, S. and Baldava, S. (2013), "A framework for performance-based wind engineering", ATC & SEI Conference on Advances in Hurricane Engineering: Learning from Our Past, Miami, U.S.A.
  113. Griffis, L.G. (1993), "Serviceability limit states under wind loads", Eng. J.Amer. Institute Steel Const., 30 (1), 1-16.
  114. Gumbel, E.J. (1954), "Statistical theory of extreme values and some practical applications", NBS Appl. Mathem. Series, 33.
  115. Gunay, S. and Mosalam, K.M. (2013), "PEER performance-based earthquake engineering methodology, revisited", J. Earthq. Eng., 17(6), 829-858. https://doi.org/10.1080/13632469.2013.787377.
  116. Hamburger, R.O. (1996), "Implementing performance-based seismic design in structural engineering practice", Proceedings of the 11th World Conference on Earthquake Engineering, Acapulco, Mexico.
  117. Harris, R. (1968), "On the spectrum and auto-correlation function of gustiness in high winds", No. 5273, Electrical Research Association.
  118. Hart, G.C. and Jain, A. (2011), "Nonlinear response of tall buildings subjected to wind loads", Struct. Des. Tall Spec. Build., 20(S1), S63-S65.
  119. Hart, G.C. and Jain, A. (2014), "Performance-based wind evaluation and strengthening of existing tall concrete buildings in the Los Angeles region: dampers, nonlinear time history analysis and structural reliability", Struct. Des. Tall Spec. Build., 23(16), 1256-1274. https://doi.org/10.1002/tal.1139.
  120. Hatzigeorgiou, G.D., Papagiannopoulos, G.A. and Beskos, D.E. (2011), "Evaluation of maximum seismic displacements of SDOF systems from their residual deformation", Eng. Struct., 33(12), 3422-3431. https://doi.org/10.1016/j.engstruct.2011.07.006.
  121. Haukaas, T. (2008), "Unified reliability and design optimization for earthquake engineering", Probab. Eng. Mech., 23(4), 471-481. https://doi.org/10.1016/j.probengmech.2007.10.008.
  122. Haukaas, T. and Bohl, A. (2009), "Comparison of approaches for performance-based earthquake engineering", Workshop on Performance-based Engineering, Villa Orlandi, Anacapri, Italy.
  123. Herning, G., Garlock, M.M., Ricles, J., Sause, R. and Li, J. (2009), "An overview of self-centering steel moment frames", Structures Congress 2009: Don't Mess with Structural Engineers: Expanding Our Role, Austin, Texas, U.S.A.
  124. Hollings, J.P. (1969), "Reinforced concrete seismic design", Bull. New Zealand Soc. Earthq. Eng., 2(3), 217-250. https://doi.org/10.5459/bnzsee.2.3.217-250
  125. Holmes, J.D. (2015), Wind Loading of Structures, CRC Press, Boka Raton, U.S.A.
  126. Hong, H.P. (2004), "Accumulation of wind induced damage on bilinear SDOF systems", Wind Struct., 7(3), 145-158. https://doi.org/10.12989/was.2004.7.3.145.
  127. Hong, H.P. (2016), "Modeling of nonstationary winds and its applications", J. Eng. Mech., 142(4), 04016004. https://doi.org/10.1061/(ASCE)EM.1943-7889.0001047.
  128. Housner, G.W., Bergman, L.A., Caughey, T.K., Chassiakos, A.G., Claus, R.O., Masri, S.F. and Yao, J.T. (1997), "Structural control: past, present, and future", J. Eng. Mech., 123(9), 897-971. https://doi.org/10.1061/(ASCE)0733-9399(1997)123:9(897).
  129. Ibarra, L.F., Medina, R.A. and Krawinkler, H. (2005), "Hysteretic models that incorporate strength and stiffness deterioration", Earthq. Eng. Struct. Dyn., 34(12), 1489-1511. https://doi.org/10.1002/eqe.495.
  130. ICBO (1976), Uniform Building Code, International Conference of Building Officials; Whittier, California.
  131. Ierimonti, L., Venanzi, I., Caracoglia, L. and Materazzi, A.L. (2019), "Life-cycle cost-based wind design of tall buildings", Conference of the Italian Association for Wind Engineering, Naples, Italy.
  132. Irwin, P. (2008), "Bluff body aerodynamics in wind engineering", J. Wind Eng. Ind. Aerod., 96(6-7), 701-712. https://doi.org/10.1016/j.jweia.2007.06.008.
  133. Irwin, P., Denoon, R. and Scott, D. (2013), Wind Tunnel Testing of High-Rise Buildings, CTBUH Technical Guides, Routledge.
  134. ISO (International Organization for Standardization). (2007), Bases for Design of Structures--serviceability of Buildings and Walkways Against Vibrations, ISO 10137, Geneva, Switzerland.
  135. ISO (International Organization for Standardization). (2009), Wind Actions on Ctructures, ISO 4354, Geneva, Switzerland.
  136. Isyumov, N. (2012), "Alan G. Davenport's mark on wind engineering", J. Wind Eng. Ind. Aerod., 104, 12-24. https://doi.org/10.1016/j.jweia.2012.02.007.
  137. Isyumov, N., Case, P.C., Ho, T.C.E. and Soegiarso, R. (2001), "Wind tunnel model studies to predict the action of wind on the projected 558 m Jakarta Tower", Wind Struct., 4(4), 299-314. https://doi.org/10.12989/was.2001.4.4.299.
  138. ITIC (2016), Cost of Hourly Downtime Soars: 81% of Enterprises Say it Exceeds $ 300K on Average, http://itic-corp.com/blog/2016/08/cost-of-hourly-downtime-soars-81-of-enterprises-say-it-exceeds-300k-on-average.
  139. Jensen, M. (1958), "The model-law for phenomena in natural wind", Ingenioren, 2(2), 121-128.
  140. Johansson, M., Linderholt, A., Bolmsvik, A., Jarnero, K., Olsson, J. and Reynolds, T. (2015), Building higher with light-weight timber structures-the effect of wind induced vibrations. In 44th International Congress and Exposition on Noise Control Engineering, The Institute of Noise Control Engineering of the U.S.A., August.
  141. Judd, J. and Charney, F. (2015), "Inelastic behavior and collapse risk for buildings subjected to wind loads", Structures Congress 2015, Portland, Oregon, U.S.A.
  142. Judd, J.P. (2018), "Windstorm resilience of a 10-story steel frame office building", ASCE-ASME J. Risk Uncertain. Eng. Syst., Part A: Civil Eng., 4(3), 04018020. https://doi.org/10.1061/AJRUA6.0000971
  143. Kaimal, J. (1973), "Turbulence spectra, length scales and structure parameters in the stable surface layer", Bound. Lay. Meteorol., 4(1-4), 289-309. https://doi.org/10.1007/BF02265239.
  144. Karacabeyli, E. and Lum, C. (2014), Technical Guide for the Design and Construction of Tall Wood Buildings in Canada, Pointe-Claire, Quebec City, Canada.
  145. Kareem, A. (1982), "A crosswind response of buildings", J. Struct. Div., 108(4), 869-887. https://doi.org/10.1016/0141-0296(82)90031-1.
  146. Kareem, A. (1990), "Reduction of wind induced motion utilizing a tuned sloshing damper", J. Wind Eng. Ind. Aerod., 36, 725-737. https://doi.org/10.1016/0167-6105(90)90070-S
  147. Kareem, A. and Gurley, K. (1996), "Damping in structures: its evaluation and treatment of uncertainty", J. Wind Eng. Ind. Aerod., 59(2), 131-157. https://doi.org/10.1016/0167-6105(96)00004-9
  148. Kareem, A. and Sun, W.J. (1990), "Dynamic response of structures with uncertain damping", Eng. Struct., 12(1), 2-8. https://doi.org/10.1016/0141-0296(90)90032-N.
  149. Kareem, A., Bernardini, E. and Spence, S.M. (2013), "Control of the wind induced response of structures", Advan. Struct. Wind Eng., Springer, Tokyo, Japan. https://doi.org/10.1007/978-4-431-54337-4_14.
  150. Kareem, A., Kijewski, T. and Tamura, Y. (1999), "Mitigation of motions of tall buildings with specific examples of recent applications", Wind Struct., 2(3), 201-251. https://doi.org/10.12989/was.1999.2.3.201
  151. Katsanos, E.I. and Vamvatsikos, D. (2017), "Yield frequency spectra and seismic design of code-compatible RC structures: an illustrative example", Earthq. Eng. Struct. Dyn., 46(11), 1727-1745. https://doi.org/10.1002/eqe.2877.
  152. Kawashima, K. (1997), "The 1996 Japanese seismic design specifications of highway bridges and the performance based design", Proceedings of Seismic Design Methodologies for the Next Generation of Codes, Bled, Slovania, June.
  153. Kim, H.J. and Christopoulos, C. (2008), "Friction damped posttensioned self-centering steel moment-resisting frames", J. Struct. Eng., 134(11), 1768-1779. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:11(1768).
  154. Krawinkler, H. and Miranda, E. (2004), "Performance-based earthquake engineering", Earthq. Eng.: From Engineering Seismol. Perform. Based Eng., 9, 1-9.
  155. Kurama, Y.C. (2002), "Hybrid post-tensioned precast concrete walls for use in seismic regions", PCI J., 47(5), 36-59. https://doi.org/10.15554/pcij.09012002.36.59.
  156. Kwok, K. and Melbourne, W.H. (1981), "Wind-induced lock-in excitation of tall structures", J. Struct. Div., 107(1), 57-72. https://doi.org/10.1061/JSDEAG.0005637
  157. Kwok, K.C.S. (1982), "Cross-wind response of tall buildings", Eng. Struct., 4(4), 256-262. https://doi.org/10.1016/0141-0296(82)90031-1.
  158. Kwon, D.K., Kareem, A., Stansel, R. and Ellingwood, B.R. (2015), "Wind load factors for dynamically sensitive structures with uncertainties", Eng. Struct., 103, 53-62. https://doi.org/10.1016/j.engstruct.2015.08.031.
  159. Lind, N.C. and Davenport, A.G. (1972), "Towards practical application of structural reliability theory", Probab. Des. RC Build., 31, 63-110.
  160. Lowes, L.N., Mitra, N. and Altoontash, A. (2004), "A beam-column joint model for simulating the earthquake response of reinforced concrete frames", PEER Report No. 2003/10, Pacific Earthquake Engineering Research Center, University of California, Berkeley.
  161. Luco, N. and Cornell, C.A. (1998), "Effects of random connection fractures on the demands and reliability for a 3-story pre-Northridge SMRF structure", Proceedings of the 6th US National Conference on Earthquake Engineering, 244, 1-12.
  162. Ma, F., Zhang, H., Bockstedte, A., Foliente, G.C. and Paevere, P. (2004), "Parameter analysis of the differential model of hysteresis", J. Appl. Mech., 71(3), 342-349. https://doi.org/10.1115/1.1668082.
  163. Ma, S.M., Bertero, V.V. and Popov, E.P. (1976), "Cyclic shear behavior of R/C plastic hinges", ASCE/EMD Specialty Conference: Dynamic Response of Structures, Los Angeles, CA, USA, March.
  164. Ma, X., Krawinkler, H. and Deierlein, G. (2011), Seismic Design, Simulation and Shake Table Testing of Self-Centering Braced Frame with Controlled Rocking and Energy Dissipating Fuses, Stanford University, Stanford, U.S.A.
  165. MacRae, G.A. and Kawashima, K. (1997), "Post-earthquake residual displacements of bilinear oscillators", Earthq. Eng. Struct. Dyn., 26(7), 701-716. https://doi.org/10.1002/(SICI)1096-9845(199707)26:7%3C701::AID-EQE671%3E3.0.CO;2-I
  166. MacRae, G.A. and Priestley, M.J.N. (1994), "Precast post-tensioned ungrouted concrete beam-column subassemblage tests", Vol. 94, No. 10, Dept. of Applied Mechanics & Engineering Sciences, University of California, San Diego.
  167. Mahmoud, H. and Chulahwat, A. (2016), "Multi-hazard multi-objective optimization of building systems with isolated floors under seismic and wind demands", In Gardoni, P. and LaFave, J.M., Multi-hazard Approaches to Civil Infrastructure Engineering, Springer, Berlin, Germany.
  168. McCormick, J., Aburano, H., Ikenaga, M. and Nakashima, M. (2008), "Permissible residual deformation levels for building structures considering both safety and human elements", Proceedings of the 14th World Conference on Earthquake Engineerin, Beijing, China.
  169. Melbourne, W.H. (1997), "Predicting the cross-wind response of masts and structural members", J. Wind Eng. Ind. Aerod., 69, 91-103. https://doi.org/10.1016/S0167-6105(97)00163-3.
  170. Merrick, R. and Bitsuamlak, G. (2009), "Shape effects on the wind-induced response of high-rise buildings", J. Wind Eng., 6(2), 1-18.
  171. Miller, C.A. and Davenport, A.G. (1998), "Guidelines for the calculation of wind speed-ups in complex terrain", J. Wind Eng. Ind. Aerod., 74, 189-197. https://doi.org/10.1016/S0167-6105(98)00016-6
  172. Miller, D.J., Fahnestock, L.A. and Eatherton, M.R. (2012), "Development and experimental validation of a nickel-titanium shape memory alloy self-centering buckling-restrained brace", Eng. Struct., 40, 288-298. https://doi.org/10.1016/j.engstruct.2012.02.037.
  173. Minciarelli, F., Gioffre, M., Grigoriu, M. and Simiu, E. (2001), "Estimates of extreme wind effects and wind load factors: influence of knowledge uncertainties", Probab. Eng. Mech., 16(4), 331-340. https://doi.org/10.1016/S0266-8920(01)00024-8.
  174. Miranda, E. (2001), "Estimation of inelastic deformation demands of SDOF systems", J. Struct. Eng., 127(9), 1005-1012. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:9(1005).
  175. Mitrani-Reiser, J., Haselton, C., Goulet, C., Porter, K., Beck, J. and Deierlein, G. (2006), "Evaluation of the seismic performance of a code-conforming reinforced-concrete frame building-part II: loss estimation", The 8th National Conference on Earthquake Engineering (100th Anniversary Earthquake Conference), San Francisco, U.S.A.
  176. Moehle, J.P. (1996), "Displacement-based seismic design criteria", Proceedings of the 11th World Conference on Earthquake Engineering, Acapulco, Mexico.
  177. Mohammadi, A. (2016), "Wind performance based design for high-rise buildings", Ph.D. Dissertation, Florida International University, U.S.A.
  178. Mohammadi, A., Azizinamini, A., Griffis, L. and Irwin, P. (2019), "Performance assessment of an existing 47-story high-rise building under extreme wind loads", J. Struct. Eng., 145(1), 04018232. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002239.
  179. Mooneghi, M.A., Irwin, P. and Chowdhury, A.G. (2015), "Exploratory studies on a bilinear aeroelastic model for tall buildings", Proceedings of the 14th International Conference on Wind Engineering, Proto Alegre, Brazil.
  180. Murakami, S., Mochida, A. and Sakamoto, S. (1997), "CFD analysis of wind-structure interaction for oscillating square cylinders", J. Wind Eng. Ind. Aerod., 72, 33-46. https://doi.org/10.1016/S0167-6105(97)00245-6.
  181. Nakai, M., Hirakawa, K., Yamanaka, M., Okuda, H. and Konishi, A. (2013), "Performance-based wind-resistant design for high-rise structures in Japan", Int. J. High-Rise Build., 2(3), 271-283. https://doi.org/10.21022/IJHRB.2013.2.3.271.
  182. Nakaki, S.D., Santon, J.F. and Sritharan, S. (1999), "An overview of the PRESS five-story precast test building", PCI J., 44(2), 26-39. http://pascal-francis.inist.fr/vibad/index.php?action=getRecordDetail&idt=1779093
  183. Nakashima, M. (1994), "Variation of ductility capacity of steel beam-columns", J. Struct. Eng., 120(7), 1941-1960. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:7(1941).
  184. Nassar, A.A. and Krawinkler, H. (1991), Seismic demands for SDOF and MDOF systems, Report No.95, John A. Blume Earthquake Engineering Center, Stanford University.
  185. NBCC (1985), National building code of Canada, National Research Council of Canada; Ottawa, Canada.
  186. NBCC (2015), National building code of Canada, National Research Council of Canada; Ottawa, Canada.
  187. NBS (National Bureau of Standards) (1977), "Performance criteria resource document for innovative construction", Report No. NBSIR 77-1316, Office of Housing & Building Technology, Washington, D.C.
  188. NEHRP (National Earthquake Hazards Reduction Program) (1988), NEHRP Recommended Provisions for the Development of Seismic Regulations for New Buildings, Building Seismic Safety Council, U.S.A.
  189. Nims, D.K., Ritcher, P.J. and Bachman, R.E. (1993), "The use of the energy dissipating restraint for seismic hazard mitigation", Earthq. Spectra, 9(3), 467-489. https://doi.org/10.1193%2F1.1585725. https://doi.org/10.1193/1.1585725
  190. Ocel, J., DesRoches, R., Leon, R.T., Hess, W.G., Krumme, R., Hayes, J.R. and Sweeney, S. (2004), "Steel beam-column connections using shape memory alloys", J. Struct. Eng., 130(5), 732-740. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:5(732).
  191. Ouyang, Z. and Spence, S.M. (2019), "A performance-based damage estimation framework for the building envelope of wind-excited engineered structures", Journal of Wind Engineering and Industrial Aerodynamics, 186, 139-154. https://doi.org/10.1016/j.jweia.2019.01.001
  192. Padgett, J.E., Dennemann, K. and Ghosh, J. (2010), "Risk-based seismic life-cycle cost-benefit (LCC-B) analysis for bridge retrofit assessment", Struct. Safety, 32(3), 165-173. https://doi.org/10.1016/j.strusafe.2009.10.003.
  193. Pagnini, L.C. and Solari, G. (1998), "Serviceability criteria for wind-induced acceleration and damping uncertainties", J. Wind Eng. Ind. Aerod., 74, 1067-1078. https://doi.org/10.1016/S0167-6105(98)00098-1.
  194. Pampanin, S., Christopoulos, C. and Nigel Priestley, M.J. (2003), "Performance-based seismic response of frame structures including residual deformations part II: multi-degree of freedom systems", J. Earthq. Eng., 7(1), 119-147. https://doi.org/10.1080/13632460309350444
  195. Panofsky, H.A. and McCormick, R.A. (1960), "The spectrum of vertical velocity near the surface", Quart. J. Royal Meteorol. Soc., 86(370), 495-503. https://doi.org/10.1002/qj.49708637006.
  196. Paulay, T. (1977), "Seismic design of ductile moment resisting reinforced concrete frames, columns: evaluation of actions", Bull. New Zealand National Soc. Earthq. Eng., 10, 85-94. https://doi.org/10.5459/bnzsee.10.2.85-94
  197. Paulay, T. and Priestley, M.N. (1992), Seismic Design of Reinforced Concrete and Masonry Buildings, John Wiley & Sons Inc., New York, U.S.A.
  198. Paulotto, C., Ciampoli, M. and Augusti, G. (2004), "Some proposals for a first step towards a Performance Based Wind Engineering", Proceedings of IFED-International Forum in Engineering Decision Making, Zurich, Switzerland.
  199. PEER (2017), Guidelines for Performance-Based Seismic Design of Tall Buildings, (Ver. 2.03), Pacific Earthquake Engineering Research Center Headquarters at the University of California, Berkeley, U.S.A.
  200. Petrini, F., Ciampoli, M. and Augusti, G. (2009), "A probabilistic framework for performance-based wind engineering", Proceedings of Fifth European and African Conference on Wind Engineering, Florence, Italy.
  201. Piccardo, G. and Solari, G. (2000), "3D wind-excited response of slender structures: closed-form solution", J. Struct. Eng., 126(8), 936-943. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:8(936).
  202. Pollino, M. and Bruneau, M. (2010), "Seismic testing of a bridge steel truss pier designed for controlled rocking", J. Struct. Eng., 136(12), 1523-1532. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000261.
  203. Porter, K. (2015), "A beginner's guide to fragility, vulnerability, and risk", Encyclopedia Earthq. Eng., 235-260.
  204. Pozos-Estrada, A., Hong, H.P. and Galsworthy, J.K. (2011), "Reliability of structures with tuned mass dampers under wind-induced motion: A serviceability consideration", Wind Struct., 14(2), 113-131. https://doi.org/10.12989/was.2011.14.2.113.
  205. Priestley, M.N. and Tao, J.R. (1993), "Seismic response of precast prestressed concrete frames with partially debonded tendons", PCI J., 38(1), 58-69. https://doi.org/10.15554/pcij.01011993.58.69
  206. Priestley, M.N., Sritharan, S., Conley, J.R. and Pampanin, S. (1999), "Preliminary results and conclusions from the PRESSS five-story precast concrete test building", PCI Journal, 44(6), 42-67. https://doi.org/10.15554/pcij.11011999.42.67
  207. Ramirez, C.M. and Miranda, E. (2012), "Significance of residual drifts in building earthquake loss estimation", Earthq. Eng. Struct. Dyn., 41(11), 1477-1493. https://doi.org/10.1002/eqe.2217.
  208. Restrepo, J.I. (2002), "New generation of earthquake resisting systems", Proceedings of the First fib Congress, Osaka, Japan.
  209. Reynolds, T., Harris, R. and Chan, W.S. (2011), "Dynamic response of tall timber buildings to wind load", The 35th Annual Symposium of IABSE/52nd Annual Symposium of IASS/6th International Conference on Space Structures, London, U.K.
  210. Rice, S.O. (1944), "Mathematical analysis of random noise", Bell Syst. Tech. J., 23(3), 282-332. https://doi.org/10.1002/j.1538-7305.1944.tb00874.x.
  211. Robertson, L.E. and Naka, T. (Eds.) (1980), Tall Building Criteria and Loading, ASCE Publications.
  212. Roshko, A. (1993), "Perspectives on bluff body aerodynamics", J. Wind Eng. Ind. Aerod., 49(1-3), 79-100. https://doi.org/10.1016/0167-6105(93)90007-B.
  213. Ruiz-Garcia, J. and Miranda, E. (2006), "Residual displacement ratios for assessment of existing structures", Earthq. Eng. Struct. Dyn., 35(3), 315-336. https://doi.org/10.1002/eqe.523.
  214. Saatcioglu, M. and Ozcebe, G. (1989), "Response of reinforced concrete columns to simulated seismic loading", ACI Struct. J., 86(1), 3-12.
  215. Saiidi, M.S. and Wang, H. (2006), "Exploratory study of seismic response of concrete columns with shape memory alloys reinforcement", ACI Struct. J., 103(3), 436.
  216. Samali, B. and Kwok, K.C.S. (1995), "Use of viscoelastic dampers in reducing wind-and earthquake-induced motion of building structures", Eng. Struct., 17(9), 639-654. https://doi.org/10.1016/0141-0296(95)00034-5.
  217. Schneider, J., Shen, Y., Stiemer, S.F. and Tesfamariam, S. (2015), "Assessment and comparison of experimental and numerical model studies of cross-laminated timber mechanical connections under cyclic loading", Construct. Build. Mater., 77, 197-212. https://doi.org/10.1016/j.conbuildmat.2014.12.029.
  218. SEAOC Vision 2000 Committee (1995), Performance-based Seismic Engineering, Structural Engineers Association of California, Sacramento, California, U.S.A.
  219. Seo, C.Y. and Sause, R. (2005), "Ductility demands on self-centering systems under earthquake loading", ACI Struct. J., 102(2), 275.
  220. Shampine, L.F. and Reichelt, M.W. (1997), "The matlab ode suite", SIAM J. Sci. Comput., 18(1), 1-22. https://doi.org/10.1137/S1064827594276424.
  221. Shen, Y.L., Schneider, J., Tesfamariam, S., Stiemer, S.F. and Mu, Z.G. (2013), "Hysteresis behavior of bracket connection in cross-laminated-timber shear walls", Construct. Build. Mater., 48, 980-991. https://doi.org/10.1016/j.conbuildmat.2013.07.050.
  222. Shinozuka, M. and Jan, C.M. (1972), "Digital simulation of random processes and its applications", J. Sound Vib., 25(1), 111-128. https://doi.org/10.1016/0022-460X(72)90600-1.
  223. Simiu, E. and Scanlan, R.H. (1996), Wind Effects on Structures: Fundamentals and Application to Design, John Willey & Sons Inc.
  224. Singer, I.A. and Raynor, G.S. (1959), "A study of the wind profile in the lowest 400 ft. of the atmosphere", No. BNL-697-T-239, Brookhaven National Lab Upton NY.
  225. Smith, M.A. and Caracoglia, L. (2011), "A Monte Carlo based method for the dynamic fragility analysis of tall buildings under turbulent wind loading", Eng. Struct., 33(2), 410-420. https://doi.org/10.1016/j.engstruct.2010.10.024.
  226. Solari, G. (2017), "Gust buffeting of slender structures and structural elements: simplified formulas for design calculations and code provisions", J. Struct. Eng., 144(2), 04017185. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001949.
  227. Solari, G. and Tubino, F. (2007), "Dynamic approach to the wind loading of structures: alongwind, crosswind and torsional response", Wind Effects Buildings Design Wind Sensitive Struct., 493, 137-166. https://doi.org/10.1007/978-3-211-73076-8_5.
  228. Spence, S.M. and Kareem, A. (2014), "Performance-based design and optimization of uncertain wind-excited dynamic building systems", Eng. Struct., 78, 133-144. https://doi.org/10.1016/j.engstruct.2014.07.026
  229. Spence, S.M.J., Chuang, W.C., Tabbuso, P., Bernardini, E., Kareem, A., Palizzolo, L. and Pirrotta, A. (2016), "Performance-based engineering of wind-excited structures: a general methodology", Geotechnical and Structural Engineering Congress 2016, Phoenix, Arizona, U.S.A.
  230. Stanton, J.F., Stone, W.C. and Cheok, G.S. (1997), "A hybrid reinforced precast frames for seismic regions", PCI J., 42(2), 20-32. https://doi.org/10.15554/pcij.03011997.20.23
  231. Stathopoulos, T. (1984), "Wind loads on low-rise buildings: a review of the state of the art", Eng. Struct., 6(2), 119-135. https://doi.org/10.1016/0141-0296(84)90005-1.
  232. Stathopoulos, T. (1997), "Computational wind engineering: past achievements and future challenges", J. Wind Eng. Ind. Aerod., 67, 509-532. https://doi.org/10.1016/S0167-6105(97)00097-4.
  233. Tabbuso, P., Spence, S.M., Palizzolo, L., Pirrotta, A. and Kareem, A. (2016), "An efficient framework for the elasto-plastic reliability assessment of uncertain wind excited systems", Struct. Safety, 58, 69-78. https://doi.org/10.1016/j.strusafe.2015.09.001.
  234. Tait, M.J., Isyumov, N. and Damatty, A.A. (2006), "Tuned Liquid Dampers to Mitigate Wind-Induced Motions of Buildings", Structures Congress 2006: Structural Engineering and Public Safety, St. Louis, Missouri, U.S.A.
  235. Takeda, T., Sozen, M.A. and Nielsen, N.N. (1970), "Reinforced concrete response to simulated earthquakes", J. Struct. Div., 96(12), 2557-2573. https://doi.org/10.1061/JSDEAG.0002765
  236. Tamura, T., Nozawa, K. and Kondo, K. (2008), "AIJ guide for numerical prediction of wind loads on buildings", J. Wind Eng. Ind. Aerod., 96(10-11), 1974-1984. https://doi.org/10.1016/j.jweia.2008.02.020.
  237. Tamura, Y. (1998), "Application of damping devices to suppress wind-induced responses of buildings", J. Wind Eng. Ind. Aerod., 74, 49-72. https://doi.org/10.1016/S0167-6105(98)00006-3.
  238. Tamura, Y., Kawai, H., Uematsu, Y., Marukawa, H., Fujii, K. and Taniike, Y. (1996), "Wind load and wind-induced response estimations in the Recommendations for Loads on Buildings, AIJ 1993", Eng. Struct., 18(6), 399-411. https://doi.org/10.1016/0141-0296(95)00121-2.
  239. Tamura, Y., Yamada, M. and Yokota, H. (1994), "Estimation of structural damping of buildings", Structures Congress XII, ASCE, Atlanta, Georgia, U.S.A.
  240. Tamura, Y., Yasui, H. and Marukawa, H. (2001), "Non-elastic responses of tall steel buildings subjected to across-wind forces", Wind Struct. 4(2), 147-162. https://doi.org/10.12989/was.2001.4.2.147.
  241. Tesfamariam, S. and Goda, K. (2015), "Seismic performance evaluation framework considering maximum and residual inter-story drift ratios: application to non-code conforming reinforced concrete buildings in Victoria, Canada", Front. Built Environ., 1, 18. https://doi.org/10.3389/fbuil.2015.00018.
  242. Tesfamariam, S., Loeppky, J.L. and Bezabeh, M.A. (2017), "Gaussian process model for maximum and residual drifts of timber-steel hybrid building", Struct. Infrastruct. Eng., 13(5), 554-566. https://doi.org/10.1080/15732479.2016.1175482.
  243. Tesfamariam, S., Sanchez-Silva, M. and Rajeev, P. (2013), "Effect of topology irregularities and construction quality on life-cycle cost of reinforced concrete buildings", J. Earthq. Eng., 17(4), 590-610. https://doi.org/10.1080/13632469.2012.762955.
  244. Tieleman, H.W. (2003), "Wind tunnel simulation of wind loading on low-rise structures: a review", J. Wind Eng. Ind. Aerod., 91(12-15), 1627-1649. https://doi.org/10.1016/j.jweia.2003.09.021.
  245. Tominaga, Y., Mochida, A., Yoshie, R., Kataoka, H., Nozu, T., Yoshikawa, M. and Shirasawa, T. (2008), "AIJ guidelines for practical applications of CFD to pedestrian wind environment around buildings", J. Wind Eng. Ind. Aerod., 96(10-11), 1749-1761. https://doi.org/10.1016/j.jweia.2008.02.058.
  246. Toranzo-Dianderas, L.A., Restrepo, J.I., Carr, A.J. and Mander, J.B. (2004), "Rocking confined masonry walls with hysteretic energy dissipators and shake-table validation", Proceedings of the 13th World Conference on Earthquake Engineering, Vancouver, Canada.
  247. Tremblay, R. (2002), "Inelastic seismic response of steel bracing members", J. Steel Res., 58(5), 665-701. https://doi.org/10.1016/S0143-974X(01)00104-3.
  248. Tremblay, R., Lacerte, M. and Christopoulos, C. (2008), "Seismic response of multistory buildings with self-centering energy dissipative steel braces", J. Struct. Eng., 134(1), 108-120. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:1(108).
  249. Tschanz, T. and Davenport, A.G. (1983), "The base balance technique for the determination of dynamic wind loads", J. Wind Eng. Ind. Aerod., 13(1-3), 429-439. https://doi.org/10.1016/0167-6105(83)90162-9.
  250. Tse, K.T., Hitchcock, P.A., Kwok, K.C., Thepmongkorn, S. and Chan, C.M. (2009), "Economic perspectives of aerodynamic treatments of square tall buildings", J. Wind Eng. Ind. Aerod., 97(9-10), 455-467. https://doi.org/10.1016/j.jweia.2009.07.005.
  251. Tsijuta O., Hayabe, Y., Ohkuma T. and Wada A. (1996), "A study on wind-induced response characteristics and prediction for inelastic structure: part 1. a case of across-wind vibration", J. Struct. Construct. Eng., (Transactions of AIJ), 61(481), 9-16.
  252. Uma, S.R., Pampanin, S. and Christopoulos, C. (2010), "Development of probabilistic framework for performance-based seismic assessment of structures considering residual deformations", J. Earthq. Eng., 14(7), 1092-1111. https://doi.org/10.1080/13632460903556509.
  253. Vamvatsikos, D. and Aschheim, M.A. (2016), "Performance-based seismic design via yield frequency spectra", Earthq. Eng. Struct. Dyn., 45(11), 1759-1778. https://doi.org/10.1002/eqe.2727.
  254. van de Lindt, J.W. and Dao, T.N. (2009), "Performance-based wind engineering for wood-frame buildings", J. Struct. Eng., 135(2), 169-177. https://doi.org/10.1061/(ASCE)0733-9445(2009)135:2(169).
  255. van de Lindt, J.W. and Potts, A. (2008), "Shake table testing of a superelastic shape memory alloy response modification device in a wood shear wall", J. Struct. Eng., 134(8), 1343-1352. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:8(1343).
  256. Van der Hoven, I. (1957), "Power spectrum of horizontal wind speed in the frequency range from 0.0007 to 900 cycles per hour", J. Meteorol. 14(2), 160-164. https://doi.org/10.1175/15200469(1957)014%3C0160:PSOHWS%3E2.0.CO;2.
  257. Vickery, B.J. (1966), "On the assessment of wind effects on elastic structures", CE Trans., Inst. Aust., 183-192.
  258. Vickery, B.J. (1970), "Wind action on simple yielding structures", J. Eng. Mech. Div., 96(2), 107-120. https://doi.org/10.1061/JMCEA3.0001221
  259. Vickery, B.J. and Steckley, A. (1993), "Aerodynamic damping and vortex excitation on an oscillating prism in turbulent shear flow", J. Wind Eng. Ind. Aerod., 49(1-3), 121-140. https://doi.org/10.1016/0167-6105(93)90009-D.
  260. Vickery, B.J., Isyumov, N. and Davenport, A.G. (1983), "The role of damping, mass and stiffness in the reduction of wind effects on structures", J. Wind Eng. Ind. Aerod., 11(1-3), 285-294. https://doi.org/10.1016/0167-6105(83)90107-1
  261. von Karman, T. (1948), "Progress in the statistical theory of turbulence", Proceedings of the National Academy of Sciences of the United States of America, 34(11), 530. https://doi.org/10.1073/pnas.34.11.530
  262. Warsido, W.P. (2013), "Reducing uncertainties in estimation of wind effects on tall buildings using aerodynamic wind tunnel tests", Ph.D. Dissertation, Florida International University, U.S.A.
  263. Warsido, W.P. and Bitsuamlak, G.T. (2015), "Synthesis of wind tunnel and climatological data for estimating design wind effects: a copula based approach", Struct. Safety, 57, 8-17. https://doi.org/10.1016/j.strusafe.2015.07.004.
  264. Wen, Y.K. (1976), "Method for random vibration of hysteretic systems", J. Eng. Mech. Div., 102(2), 249-263. https://doi.org/10.1061/JMCEA3.0002106
  265. Wen, Y.K. (1990), Structural Load Modeling and Combination for Performance and Safety Evaluation, Elsevier Science Ltd.
  266. Wen, Y.K. (2001), "Reliability and performance-based design", Struct. Safety, 23(4), 407-428. https://doi.org/10.1016/S0167-4730(02)00011-5
  267. Wen, Y.K. and Kang, Y.J. (2001a), "Minimum building life-cycle cost design criteria. I: methodology", J. Struct. Eng., 127(3), 330-337. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:3(330).
  268. Wen, Y.K. and Kang, Y.J. (2001b), "Minimum building life-cycle cost design criteria. II: applications", J. Struct. Eng., 127(3), 338-346. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:3(338).
  269. Wiebe, L. and Christopoulos, C. (2014), "Performance-based seismic design of controlled rocking steel braced frames. II: design of capacity-protected elements", J. Struct. Eng., 141(9), 04014227. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001202.
  270. Wood, D.H. (1982), "Internal boundary layer growth following a step change in surface roughness", Bound. Lay. Meteorol., 22(2), 241-244. https://doi.org/10.1007/BF00118257.
  271. Wyatt, T.A. and May, H. (1971), "The ultimate load behaviour of structures under wind loading", Proceedings of the 3rd International Conference on Wind Effects on Buildings and Structures, Tokyo, Japan.
  272. Yang, S.C., Liu, T.J. and Hong, H.P. (2017), "Reliability of tower and tower-line systems under spatiotemporally varying wind or earthquake loads", J. Struct. Eng., 143(10), 04017137. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001835.
  273. Yang, T.Y., Moehle, J., Stojadinovic, B. and Der Kiureghian, A. (2009), "Seismic performance evaluation of facilities: methodology and implementation", J. Struct. Eng., 135(10), 1146-1154. https://doi.org/10.1061/(ASCE)0733-9445(2009)135:10(1146).
  274. Yeo, G.L. and Cornell, C.A. (2005), Stochastic Characterization and Decision Bases Under Time-dependent Aftershock Risk in Performance-based Earthquake Engineering, Pacific Earthquake Engineering Research Center, Berkeley, U.S.A.
  275. Yoshie, K., Kitamura, H. and Ohkuma, T. (2005), "A prediction method for response of an elasto-plastic structure to fluctuating wind force based on energy balance", CTBUH New York Conference, U.S.A.
  276. Zeynalian, M., Ronagh, H.R. and Dux, P. (2012), "Analytical description of pinching, degrading, and sliding in a bilinear hysteretic system", J. Eng. Mech., 138(11), 1381-1387. https://doi.org/10.1061/(ASCE)EM.1943-7889.0000442.
  277. Zizmond, J. and Dolsek, M. (2017), "The formulation of risk-targeted behaviour factor and its application to reinforced concrete buildings", Proceedings of the 16th world conference on earthquake engineering, Santiago, Chile.

피인용 문헌

  1. Wind engineering for high-rise buildings: A review vol.32, pp.3, 2020, https://doi.org/10.12989/was.2021.32.3.249