DOI QR코드

DOI QR Code

Shear strength and deformation of steel fibre-reinforced concrete beams after fire

  • 투고 : 2019.06.15
  • 심사 : 2020.07.23
  • 발행 : 2020.08.25

초록

In this study eleven beam of steel fibre-reinforced concrete were tested on concentrated load in order to evaluate the shear strength and deformation of the beams after burning. Variables considered in the test include spaces of shear reinforcement (stirrups) and temperature (normal temperature at 38℃, 300℃, 600℃ and 900℃). The steel fiber used is set at 0.5% of the concrete volume. The phenomenon of the test results shows that although the beams were tested to achieve shear failure, the fact that all the tested beams did not encounter any shear failure. It has shown the influence of steel fibers and stirrups that plays a role in determining the mode of collapse. The concrete shear capacity of steel fibrous concrete beams installed with stirrups in altered spacing variations is not significantly different from each other, while beam deformability increases when the space stirrups are reduced. Furthermore, models of the developed-steel fibrous shear strength are compared and discussed with experimental results.

키워드

참고문헌

  1. ACI Committee 318 (2014), Building Code Requirements for Structural Concrete (ACI-318-14) and Commentary (318R-14), American Concrete Institute, Farmington Hills, MI.
  2. ACI Committee 544 (1988), "Design considerations for steel fibre reinforced concrete", ACI Struct. J., 85(5), 1-18.
  3. Antonius, Imran, I. and Setiyawan, P. (2017), "On the confined high-strength concrete and need of future research", Procedia Eng., 171, 121-130. https://doi.org/10.1016/j.proeng.2017.01.318.
  4. Antonius, Purwanto and Harprastanti, P. (2019), "Experimental study of the flexural strength and ductility of post burned steel fiber RC beams", Int. J. Technol., 10(2), 428-437. https://doi.org/10.14716/ijtech.v10i2.2097
  5. Antonius, Widhianto, A., Darmayadi, D. and Asfari, G.D. (2014), "Fire resistance of normal and high-strength concrete with contains of steel fibre", Asian J. Civil Eng., 15(5), 655-669.
  6. Araujo, D. de Lima, Nunes, F.G.T., Filho, R.D.T. and Andrade, M.A.S. (2014), "Shear strength of steel fiber-reinforced concrete beams", Acta Scientiarum, 36(3), 389-397. https://doi.org/10.4025/actascitechnol.v36i3.19005
  7. Ashour, S.A., Hasanain, G.S. and Wafa, F.F. (1992), "Shear behavior of high-strength fiber reinforced concrete beams", ACI Struct. J., 89(2), 176-184.
  8. Barros, J.A.O., Lourenco, L.A.P., Soltanzadeh, F. and Taheri, M. (2013), "Steel fibre reinforced concrete for elements failing in bending and in shear", Adv. Concrete Constr., 1(1), 1-27. http://dx.doi.org/10.12989/acc.2013.1.1.001.
  9. Blesak, L., Goremikins, V., Wald, F. and Sajdlova, T. (2016), "Constitutive model of steel fibre reinforced concrete subjected to high temperatures", Acta Polytechnica, 56(6), 417-424. https://doi.org/10.14311/AP.2016.56.0417.
  10. Gomes, L.D. dos Santos, Oliveira, D.R.C., Neto, B.N. de Moraes, Medeiros, A.B., Macedo, A.N. and Silva, F.A.C. (2018), "Experimental analysis of the efficiency of steel fibers on shear strength of beams", Lat. Am. J. Solid. Struct., 15(7), 1-16. https://doi.org/10.1590/1679-78254710.
  11. Han, A.L., Antonius and Okiyarta, A.W. (2015), "Experimental study of steel fiber reinforced concrete beams with confinement", Procedia Eng., 125, 1030-1035. https://doi.org/10.1016/j.proeng.2015.11.158.
  12. Indonesian National Standard (2012), Procedures of Mixed Selection for Normal Concrete, Heavy Concrete and Mass Concrete, SNI 7656:2012. (in Indonesian)
  13. Indonesian National Standard (2013), Requirements of Structural Concrete for Building, SNI 2847-2013. (in Indonesian)
  14. Jain, K. and Singh, B. (2013), "Steel fibres as minimum shear reinforcement in reinforced concrete beams", Mag. Concrete Res., 65(7), 430-440. https://doi.org/10.1680/macr.12.00113.
  15. Kwak, Y.K., Eberhard, M.O., Kim, W.S. and Kim, J. (2002), "Shear strength of steel fiber-reinforced concrete beams without stirrups", ACI Struct. J., 99(4), 530-538.
  16. Lim, W.Y. and Hong, S.G. (2016), "Shear tests for ultra-high performance fiber reinforced concrete (UHPFRC) beams with shear reinforcement", Int. J. Concrete Struct. Mater., 10(2), 177-188. https://doi.org/10.1007/s40069-016-0145-8.
  17. Luo, J.W. and Vecchio, F.J. (2016), "Behavior of steel fiber-reinforced concrete under reversed cyclic shear", ACI Struct. J., 113(1), 75-84.
  18. Narayanan, R. and Darwish, I.Y.S. (1987), "Use of steel fibers as shear reinforcement", ACI Struct. J., 84(3), 216-227.
  19. Paultre, P., Eid, R., Langlois, Y. and Levesque, Y. (2010), "Behavior of steel fiber-reinforced high-strength concrete columns under uniaxial compression", J. Struct. Eng., 136(10), 1225-1235. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000211.
  20. Ponikiewski, T., Katzer, J., Kilijanek, A. and Kuzminska, E. (2018), "Mechanical behaviour of steel fibre reinforced SCC after being exposed to fire", Adv. Concrete Constr., 6(6), 631-643. http://dx.doi.org/10.12989/acc.2018.6.6.631.
  21. Sharma, A.K. (1986), "Shear strength of steel fiber reinforced concrete beams", ACI J., 83(4), 624-628.
  22. Tadepalli, P.R., Dhonde, H.B., Mo, Y.L. and Hsu, T.T. (2015), "Shear strength of prestressed steel fiber concrete I-beams", Int. J. Concrete Struct. Mater., 9(3), 267-281. https://doi.org/10.1007/s40069-015-0109-4.
  23. Yoon, Y.S., Yang, J.M., Yoo, D.Y. and Yuan, T.F. (2017), "Replacing stirrups with steel fibers in high-strength concrete beams", The 2017 World Congress on Advances in Structural Engineering and Mechanics (ASEM 17), Korea.