Coupled systems mechanics

  • 제9권4호
  • /
  • Pages.381-396
  • /
  • 2020
  • /
  • 2234-2184(pISSN)
  • /
  • 2234-2192(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Investigation of two parallel lengthwise cracks in an inhomogeneous beam of varying thickness

  • Rizov, Victor I. (Department of Technical Mechanics, University of Architecture, Civil Engineering and Geodesy)
  • 투고 : 2020.01.29
  • 심사 : 2020.04.03
  • 발행 : 2020.08.25
⟨ 이전 논문 다음 논문 ⟩

초록

Analytical investigation of the fracture of inhomogeneous beam with two parallel lengthwise cracks is performed. The thickness of the beam varies continuously along the beam length. The beam is loaded in three-point bending. Two beam configurations with different lengths of the cracks are analyzed. The two cracks are located arbitrary along the thickness of the beam. Solutions to the strain energy release rate are derived assuming that the material has non-linear elastic mechanical behavior. Besides, the beam exhibits continuous material inhomogeneity along its thickness. The balance of the energy is analyzed in order to derive the strain energy release rate. Verifications of the solutions are carried-out by considering the complementary strain energy stored in the beam configurations. The influence of the continuous variation of the thickness along the beam length on the lengthwise fracture behavior is investigated. The dependence of the lengthwise fracture on the lengths of the two parallel cracks is also studied.

키워드

참고문헌

  1. Altunsaray, E. and Bayer, I. (2014), "Buckling of symmetrically laminated quasi-isotropic thin rectangular platesˮ, Steel Compos. Struct., 17, 305-320. https://doi.org/10.12989/scs.2014.17.3.305.
  2. Butcher, R.J., Rousseau, C.E. and Tippur, H.V. (1999), "A functionally graded particulate composite: measurements and failure analysisˮ, Acta. Mater., 47(2), 259-268. https://doi.org/10.1016/S1359-6454(98)00305-X.
  3. Dolgov, N.A. (2005), "Determination of stresses in a two-layer coating", Strength Mater., 37(2), 422-431. https://doi.org/10.1007/s11223-005-0053-7.
  4. Dolgov, N.A. (2016), "Analytical methods to determine the stress state in the substrate-coating system under Mechanical loads", Strength Mater., 48(1), 658-667. https://doi.org/10.1007/s11223-016-9809-5.
  5. Gasik, M.M. (2010), "Functionally graded materials: bulk processing techniquesˮ, Int. J. Mater. Product Technol., 39(1-2), 20-29. https://doi.org/10.1504/IJMPT.2010.034257.
  6. Hedia, H.S., Aldousari, S.M., Abdellatif, A.K. and Fouda, N.A. (2014), "New design of cemented stem using functionally graded materials (FGM)ˮ, Biomed. Mater. Eng., 24(3), 1575-1588. https://doi.org/10.3233/BME-140962.
  7. Hirai, T. and Chen, L. (1999), "Recent and prospective development of functionally graded materials in Japanˮ, Mater. Sci. Forum., 308-311(4), 509-514. https://doi.org/10.4028/www.scientific.net/MSF.308-311.509.
  8. Lukash, P.A. (1998), Fundamentals of Non-linear Structural Mechanics, Stroizdat.
  9. Mahamood, R.M. and Akinlabi, E.T. (2017), Functionally Graded Materials, Springer.
  10. Markworth, A.J., Ramesh, K.S. and Parks, Jr. W.P. (1995), "Review: modeling studies applied to functionally graded materialsˮ, J. Mater. Sci., 30(3), 2183-2193. https://doi.org/10.1007/BF01184560.
  11. Miyamoto, Y., Kaysser, W.A., Rabin, B.H., Kawasaki, A. and Ford, R.G. (1999), Functionally Graded Materials: Design, Processing and Applications, Kluwer Academic Publishers, Dordrecht/London/Boston.
  12. Nemat-Allal, M.M., Ata, M.H., Bayoumi, M.R. and Khair-Eldeen, W. (2011), "Powder metallurgical fabrication and microstructural investigations of Aluminum/Steel functionally graded materialˮ, Mater. Sci. Appl., 2(5), 1708-1718. https://doi.org/10.4236/msa.2011.212228.
  13. Rizov, V.I. (2017), "Analysis of longitudinal cracked two-dimensional functionally graded beams exhibiting material non-linearityˮ, Frattura ed Integrita Strutturale, 41, 498-510. https://doi.org/10.3221/IGFESIS.41.61.
  14. Rizov, V.I. (2018), "Non-linear longitudinal fracture in a functionally graded beamˮ, Coupl. Syst. Mech., 7(4), 441-453. https://doi.org/10.12989/csm.2018.7.4.441.
  15. Rizov, V.I. (2018). "Analysis of cylindrical delamination cracks in multilayered functionally graded nonlinear elastic circular shafts under combined loadsˮ, Frattura ed Integrita Strutturale, 46, 158-117. https://doi.org/10.3221/IGF-ESIS.46.16.
  16. Rizov, V.I. (2019), "Influence of material inhomogeneity and non-linear mechanical behavior of the material on delamination in multilayered beamsˮ, Frattura ed Integrita Strutturale, 47, 468-481. https://doi.org/10.3221/IGF-ESIS.47.37.
  17. Rizov, V.I. (2019), "Influence of sine material gradients on delamination in multilayered beamsˮ, Coupl. Syst. Mech., 8(1), 1-17. https://doi.org/10.12989/csm.2019.8.1.001.
  18. Ṣimṣek, M. (2012), "Nonlocal effects in the free longitudinal vibration of axially functionally graded tapered nanorodsˮ, Comput. Mater. Sci., 61, 257-265. https://doi.org/10.1016/j.commatsci.2012.04.001.
  19. Ṣimṣek, M. (2015), "Bi-directional functionally graded materials (BDFGMs) for free and forced vibration of Timoshenko beams with various boundary conditionsˮ, Compos. Struct., 133, 968-978. https://doi.org/10.1016/j.compstruct.2015.08.021.
  20. Ṣimṣek, M., Kocaturk, T. and Akbaṣ, D. (2013), "Static bending of a functionally graded microscale Timoshenko beam based on the modified couple stress theoryˮ, Compos. Struct., 95, 740-747. https://doi.org/10.1016/j.compstruct.2012.08.036.
  21. Szekrenyes, A. (2010), "Fracture analysis in the modified split-cantilever beam using the classical theories of strength of materialsˮ, J. Phys.: Conf. Ser., 240(1), 012030. https://doi.org/10.1088/1742-6596/240/1/012030.
  22. Szekrenyes, A. (2012), "J-integral for delaminated beam and plate modelsˮ, Periodica Polytechnica, Mech. Eng., 56(1), 63-71. https://doi.org/10.3311/pp.me.2012-1.10.
  23. Tokovyy, Y. (2019), "Solutions of axisymmetric problems of elasticity and thermoelasticity for an inhomogeneous space and a half spaceˮ, J. Math. Sci., 240(1), 86-97. https://doi.org/10.1007/s10958-019-04337-3.
  24. Tokovyy, Y. and Ma, C.C. (2017), "Three-dimensional elastic analysis of transversely-isotropic compositesˮ, J. Mech., 33(6), 821-830. https://doi.org/10.1017/jmech.2017.91.
  25. Tokovyy, Y. and Ma, C.C. (2019), "Elastic analysis of inhomogeneous solids: History and development in briefˮ, J. Mech., 18(1), 1-14. https://doi.org/10.1017/jmech.2018.57.
  26. Uslu Uysal, M. (2016), "Buckling behaviours of functionally graded polymeric thin-walled hemispherical shellsˮ, Steel Compos. Struct., 21(1), 849-862. https://doi.org/10.12989/scs.2016.21.4.849.
  27. Uslu Uysal, M. and Guven, U. (2015), "Buckling of functional graded polymeric sandwich panel under different load casesˮ, Compos. Struct., 121, 182-196. https://doi.org/10.1016/j.compstruct.2014.11.012.
  28. Uslu Uysal, M. and Guven, U. (2016), "A bonded plate having orthotropic inclusion in adhesive layer under in-plane shear loadingˮ, J. Adhes., 92, 214-235. https://doi.org/10.1080/00218464.2015.1019064.
  29. Uslu Uysal, M. and Kremzer, M. (2015), "Buckling behaviour of short cylindrical functionally gradient polymeric materialsˮ, Acta Physica Polonica, A127, 1355-1357. https://doi.org/10.12693/APhysPolA.127.1355.
  30. Wu, X.L., Jiang, P., Chen, L., Zhang, J.F., Yuan, F.P. and Zhu, Y.T. (2014), "Synergetic strengthening by gradient structureˮ, Mater. Res. Lett., 2(1), 185-191. https://doi.org/10.1080/21663831.2014.935821.