DOI QR코드

DOI QR Code

Probabilistic seismic assessment of RC box-girder bridges retrofitted with FRP and steel jacketing

  • Naseri, Ali (Department of Structural Engineering, Babol Noshirvani University of Technology) ;
  • Roshan, Alireza Mirzagoltabar (Department of Structural Engineering, Faculty of Civil Engineering, Babol Noshirvani University of Technology) ;
  • Pahlavan, Hossein (Department of Earthquake Engineering, Shahrood University of Technology) ;
  • Amiri, Gholamreza Ghodrati (Center of Excellence for Fundamental Studies in Structural Engineering, School of Civil Engineering, Iran University of Science and Technology)
  • 투고 : 2019.06.30
  • 심사 : 2020.02.21
  • 발행 : 2020.08.25

초록

Due to susceptibility of bridges in the past earthquakes, vulnerability assessment and strengthening of bridges has gained a particular significance. The objective of the present study is to employ an analytical method for the development of fragility curves, as well as to investigate the effect of strengthening on the RC box-girder bridges. Since fragility curves are used for pre-and post-earthquake planning, this paper has attempted to adopt the most reliable modeling assumptions in order to increase the reliability. Furthermore, to acknowledge the interaction of soil, abutment and pile, the effect of different strengthening methods, such as using steel jacketing and FRP layers, the effect of increase in the bridge pier diameter, and the effect of vertical component of earthquake on the vulnerability of bridges in this study, a three-span RC box-girder bridge was modeled in 9 different cases. Nonlinear dynamic analyses were carried out on the studied bridges subjected to 100 ground motion records via OpenSEES platform. Therefore, the fragility curves were plotted and compared in the four damage states. The results revealed that once the interaction of soil and abutment and the vertical component of the earthquake are accounted for in the calculations, the median fragility is reduced, implying that the bridge becomes more vulnerable. It was also confirmed that steel jackets and FRP layers are suitable methods for pier strengthening which reduces the vulnerability of the bridge.

키워드

참고문헌

  1. Abbasi, M., Zakeri, B. and Amiri, G.G. (2015), "Probabilistic seismic assessment of multiframe concrete box-girder bridges with unequal-height piers", J. Perform. Constr. Facil., 30(2), 04015016. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000753.
  2. Abdollahzadeh, G., Sazjini, M., Shahaky, M., Tajrishi, F.Z. and Khanmohammadi, L. (2014), "Considering potential seismic sources in earthquake hazard assessment for Northern Iran", J. Seismol., 18(3), 357-369. https://doi.org/10.1007/s10950-013-9412-1.
  3. Alim, H. and Zisan, M.B. (2013), "Evaluation of probabilistic failure of bridge pire", Int. J. Struct. Civil Eng., 2(2), Research Paper, May.
  4. Aviram, A., Mackie, K. and Stojadinovie, B. (2008), "Guidelines for nonlinear analysis bridge structure in Californai", Technical 2008/03, Pacific Earthquake Engineering Research Center, University of California, Berkeley.
  5. Baker, J.W., Ling, T., Shahi, S.K. and Jayaram, N. (2011), "New ground motion selection procedures and selected motions for the PEER transportation research program", Draft Report, Pacific Earthquake Engineering Research Center, University of California, Berkeley.
  6. Baloevic, G., Radnic, J., Grgic, N., Matesan, D. and Smilovic, M. (2016), "Numerical model for nonlinear analysis of composite concrete-steel-masonry bridges", Coupl. Syst. Mech., 5(1), 1-20. http://dx.doi.org/10.12989/csm.2016.5.1.001.
  7. Bavirisetty, R., Vinayagamoorthy, M. and Duan, L. (2000), Dynamic Analysis, Bridge Engineering Handbook, Eds. W.F. Chen and L. Duan, CRC Press, Boca Raton, FL.
  8. CALTRANS (2007), Reinforced Concrete Bridge Capacity Assessment Training Manual, Structure Maintenance and Investigations Rep., Sacramento, CA.
  9. CALTRANS (2010-2012), Personal Communication with the P266 Fragility Project Advisory Panel Members Including Roblee,
  10. Chang, G.A. and Mander, J.B. (1994), "Seismic energy based fatigue damage analysis of bridge columns, Part 1- Evaluation of seismic capacity", Technical Rep. NCEER-94-0006, State Univ. of New York, Buffalo, NY.
  11. Choi, E. (2002), "Seismic analysis and retrofit of mid-America bridges", Ph.D. Thesis, Georgia Institute of Technology, Atlanta.
  12. Dutta, A. (1999), "Energy based seismic analysis and design of highway bridges", Ph.D. Thesis, State Univ. of New York, Buffalo.
  13. Ellingwood, B. and Hwang, H. (1985), "Probabilistic descriptions of resistance of safety related structures in nuclear plants", Nucl. Eng. Des., 88(2), 169-178. https://doi.org/10.1016/0029-5493(85)90059-7.
  14. Falamarz-Sheikhabadi, M.R. and Zerva, A. (2017), "Analytical seismic assessment of a tall long-span curved reinforced-concrete bridge. Part I: numerical modeling and input excitation", J. Earthq. Eng., 21(8), 1305-1334. https://doi.org/10.1080/13632469.2016.1211565.
  15. Fang, J., Li, Q., Jeary, A. and Liu, D. (1999), "Damping of tall buildings: Its evaluation and probabilistic characteristics", Struct. Des. Tall Build., 8(2), 145-153. https://doi.org/10.1002/(SICI)1099-1794(199906)8:2<145::AID-TAL127>3.0.CO;2-1.
  16. FEMA356 (2000), Prestandard, Commentary for the Seismic Rehabilitation of Buildings, Washington, DC: Federal Emergency Management Agency, 7.
  17. HAZUS-MH [Computer software], Federal Emergency Management Agency, Washington, DC.
  18. Jeon, J.S., DesRoches, R., Kim, T. and Choi, E. (2016), "Geometric parameters affecting seismic fragilities of curved multi-frame concrete box-girder bridges with integral abutments", Eng. Struct., 122, 121-143. https://doi.org/10.1016/j.engstruct.2016.04.037.
  19. Jeon, J.S., Shafieezadeh, A., Lee, D.H., Choi, E. and DesRoches, R. (2015), "Damage assessment of older highway bridges subjected to three-dimensional ground motions: characterization of shear-axial force interaction on seismic fragilities", Eng. Struct., 87, 47-57. https://doi.org/10.1016/j.engstruct.2015.01.015.
  20. Mandar, J.B., Priestley, M.J.N. and Park, R. (1988), "Observed stress strain behavior of confined concrete", J. Struct. Eng., 114(8), 1827-1849. https://doi.org/10.1061/(ASCE)0733-9445(1988)114:8(1827).
  21. Mander, J.B., Kim, D.K., Chen, S.S. and Premus, G.J. (1996), "Response of steel bridge bearings to the reversed cyclic loading", Rep. No. NCEER 96-0014, NCEER.
  22. McKenna, F., Scott, M.H. and Fenves, G.L. (2009), "Nonlinear finite-element analysis software architecture using object composition", J. Comput. Civil Eng., 24(1), 95-107. https://doi.org/10.1061/(ASCE)CP.1943-5487.0000002.
  23. Megally, S.H., Silva, P.F. and Seible, F. (2001), "Seismic response of sacrificial shear keys in bridge abutments", Report No. SSRP-200l/23, Department of Structural Engineering, University of California, San Diego.
  24. Menegotto, M. and Pinto, P.E. (1973), "Method of analysis for cyclically loaded reinforced concrete plane frames including changes in geometry and non-elastic behavior of elements under combined normal force and bending", Proc., IABSE Symp. on Resistance and Ultimate Deformability of Structures Acted on by Well-Defined Repeated Loads, Lisbon, Portugal.
  25. Muthukumar, S. and DesRoches, R. (2006), "A Hertz contact model with non-linear damping for pounding simulation", Earthq. Eng. Struct. Dyn., 35(7), 811-828. https://doi.org/10.1002/eqe.557.
  26. Naseri, A., Pahlavan, H. and Ghodrati Amiri, G. (2017), "Probabilistic seismic assessment of RC frame structures in North of Iran using fragility curves", J. Struct. Constr. Eng., 4(4), 58-78. https://doi.org/10.22065/jsce.2017.78827.1095.
  27. Nielson, B. (2005), "Analytical fragility curves for highway bridges in moderate seismic zones", PhD Thesis, Georgia Institute of Technology.
  28. OpenSEES [Computer software], Pacific Earthquake Engineering Research Center, Berkeley, CA.
  29. Padgett, J.E. (2007), "Seismic vulnerability assessment of retrofitted bridges using probabilistic methods", Ph.D. Thesis, Georgia Institute of Technology, Atlanta.
  30. Padgett, J.E. and DesRoches, R. (2008), "Methodology for the development of analytical fragility curves for retrofitted bridges", Earthq. Eng. Struct. Dyn., 37(8), 1157-1174. https://doi.org/10.1002/eqe.801.
  31. Pahlavan, H. (2015), "Seismic fragility curve development for curved RC box-girder bridges", PhD Thesis, Iran University of Science and Technology, School of Civil Engineering.
  32. Pahlavan, H., Naseri, A. and Einolahi, A. (2018), "Probabilistic seismic vulnerability assessment of RC frame structures retrofitted with steel jacketing", Amirkabir Journal of Civil Engineering. https://doi.org/10.22060/ceej.2018.13692.5459.
  33. Pahlavan, H., Zakeri, B., Amiri, G.G. and Shaianfar, M. (2015), "Probabilistic vulnerability assessment of horizon-tally curved multiframe RC box-girder highway bridges", J. Perform. Constr. Facil., 30(3), 04015038. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000780.
  34. PEER, (Pacific Earthquake Engineering Research), Regents of the University of California, http://opensees.berkeley.edu/.
  35. Raheem, S.E.A. (2018), "Structural control of cable-stayed bridges under traveling earthquake wave excitation", Coupl. Syst. Mech., 7(3), 269-280. http://dx.doi.org/10.12989/csm.2018.7.3.269.
  36. Ramanathan, K., DesRoches, R. and Padgett, J.E. (2012), "A comparison of pre-and post-seismic design considerations in moderate seismic zones through the fragility assessment of multispan bridge classes", Eng. Struct., 45, 559-573. https://doi.org/10.1016/j.engstruct.2012.07.004.
  37. Ramanathan, K.N. (2012), "Next generation seismic fragility curves for California bridges incorporating the evolution in seismic design philosophy", PhD Thesis, Georgia Institute of Technology, Atlanta.
  38. Roshan, A.M.G., Naseri, A. and Pati, Y.M. (2018), "Probabilistic evaluation of seismic vulnerability of multi-span bridges in north of Iran", J. Struct. Constr. Eng., 5(1), 36-54. https://doi.org/10.22065/jsce.2017.68948.1009.
  39. Saadeghvaziri, M.A. and Foutch, D.A. (1991), "Dynamic behavior of RC highway bridges under the combined effect vertical and horizontal earthquake motion", Earthq. Eng. Struct. Dyn., 20, 535-549. https://doi.org/10.1002/eqe.4290200604.
  40. Sakino, K. (1994), "Stress-strain curve of concrete confined by rectilinear steels", J. Struct. Constr. Eng., AIJ, 461, 95-104. https://doi.org/10.3130/aijs.59.95_1
  41. Schrage, I. (1981), "Anchoring of Bearings by Friction", Joint Sealing and Bearing Systems for Concrete Structures, World Congress on Joints and Bearings, Vol. 1, Niagara Falls, NY, USA. American Concrete Inst.
  42. Shamekhi amiri, M., Naseri, A. and Messgarpour amiri, M. (2019), "Seismic vulnerability assessment of reinforced concrete structures equipped with eccentrically braced frames having vertical link", Amirkabir Journal of Civil Engineering. https://doi.org/10.22060/ceej.2019.14313.5621.
  43. Shamsabadi, A. and Yan, L. (2008), "Closed-form force-displacement backbone curves for bridge abutment backfill systems", Proceedings of the Geotechnical Earthquake Engineering and Soil Dynamics IV Congress, ASCE, 1-10. https://doi.org/10.1061/40975(318)159.
  44. Shamsabadi, A., Khalili-Tehrani, P., Stewart, J.P. and Taciroglu, E. (2010), "Validated simulation models for lateral response of bridge abutments with typical backfills", J. Bridge Eng., 15(3), 302-311. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000058.
  45. Shaw, I.D. andrawes, B.O. (2017), "Finite element analysis of CFRP laminate repairs on damaged end regions of prestressed concrete bridge girders", Adv. Comput. Des., 2(2), 147-168. http://dx.doi.org/10.12989/acd.2017.2.2.147.
  46. Shinozuka, M., Feng, M.Q., Kim, H.K. and Kim, S.H. (2000), "Nonlinear static procedure for fragility curve development", J. Eng. Mech., 126(12), 1287-1295. https://doi.org/10.1061/(ASCE)0733-9399(2000)126:12(1287).
  47. Siqueira, G.H., Sanda, A.S., Paultre, P. and Padgett, J.E. (2014), "Fragility curves for isolated bridges in eastern Canada using experimental results", Eng. Struct., 74, 311-324. https://doi.org/10.1016/j.engstruct.2014.04.053.
  48. Tondini N. and Stojadinovic. B. (2012), "Probabilistic seismic demand model for curved reinforced concrete bridges", Bull. Earthq. Eng., 10, 1455-1479. https://doi.org/10.1007/s10518-012-9362-y.
  49. Wu, Y.F. and Wang, L.M. (2009), "Unified strength model for square and circular concrete columns confined by external jacket", J. Struct. Eng., 135(3), 253-261. https://doi.org/10.1061/(ASCE)0733-9445(2009)135:3(253).
  50. Zhang, J. and Makris, N. (2002), "Seismic response analysis of highway overcrossings including soil structure interaction", Earthq. Eng. Struct. Dyn., 31(11), 1967-1991. https://doi.org/10.1002/eqe.197.

피인용 문헌

  1. Effects of curvature radius on vulnerability of curved bridges subjected to near and far-field strong ground motions vol.7, pp.4, 2020, https://doi.org/10.12989/smm.2020.7.4.367