Steel and Composite Structures

  • 제36권5호
  • /
  • Pages.569-586
  • /
  • 2020
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Behavior and resistance of truss-type shear connector for composite steel-concrete beams

  • Lima, Jerfson M. (Department of Civil and Environmental Engineering, University of Brasilia) ;
  • Bezerra, Luciano M. (Department of Civil and Environmental Engineering, University of Brasilia) ;
  • Bonilla, Jorge (Department of Applied Mathematics, University of Ciego de Avila) ;
  • Silva, Ramon S.Y.R.C. (Department of Civil and Environmental Engineering, University of Brasilia) ;
  • Barbosa, Wallison C.S. (Department of Civil and Environmental Engineering, University of Brasilia)
  • 투고 : 2019.03.10
  • 심사 : 2020.08.10
  • 발행 : 2020.09.10
⟨ 이전 논문 다음 논문 ⟩

초록

The behavior of composite steel-concrete beams depends on the transmission of forces between two parts: the concrete slab and the steel I-beam. The shear connector is responsible for the interaction between these two parts. Recently, an alternative shear connector, called Truss Type connector, has been developed; it aligns efficient structural behavior, fast construction and implementation, and low cost when compared to conventional connectors applied in composite structures. However, there is still a lack of full understanding of the mechanical behavior of the Truss Type connector, due to its novelty. Thus, this study aims to analyze the influence of variation of geometric and physical parameters on the shear resistance of the Truss Type connector. In order to investigate those parameters, a non-linear finite element model, able to simulate push-out tests of Truss Type connectors, was specifically developed and validated with experimental results. A thorough parametric study, varying the height, the angle between rods, the diameter, and the concrete strength, was conducted to evaluate the shear resistance of the Truss Type connector. In addition, an equation to predict the resistance of the original Truss Type shear connector was proposed.

키워드

과제정보

The authors would like to thank CAPES (the Brazilian Coordination for the Improvement of Higher Education Personnel) and CNPq (the National Council for Scientific and Technological Development) for the financial supports for this research.

참고문헌

  1. AASHTO (2014), Load and Resistance Factor Design (LRFD) Bridge design specifications, (7th Edition); American Association of State Highway and Transportation Officials, Washington, D.C., USA.
  2. AISC (2010), Load and Resistance Factor Design (LRFD) Specification for Structural Steel Building; American Institute of Steel Construction, Chicago, IL, USA.
  3. ABAQUS (2014-a), User's Manual, Version 6.14-1, Dessault Systemes Simulia Corp, Provice, RI, USA.
  4. ABAQUS (2014-b), Theory Manual, Version 6.14-1, Dessault Systemes Simulia Corp, Provice, RI, USA.
  5. ABNT NBR 6118 (2014), Design of concrete structures - Procedure, Brazilian Association for Technical Standards, Rio de Janeiro, Brazil (In Portuguese).
  6. Alfarah, B., Lopez-Almansa, F. and Oller, S. (2017), "New methodology for calculating damage variables evolution in Plastic Damage Model for RC structures", Eng. Struct., 132, 70-86. https://doi.org/10.1016/j.engstruct.2016.11.022.
  7. Araujo, D. de L., Sales, M.W.R., Paulo, S.M. de and Debs, A.L.H. de C. El. (2016), "Headed steel stud connectors for composite steel beams with precast hollow-core slabs with structural topping", Eng. Struct., 107, 135-150. https://doi.org/10.1016/j.engstruct.2015.10.050.
  8. Ban, H., Bradford, M.A., Uy, B. and Liu, X. (2016), "Available rotation capacity of composite beams with high-strength materials under sagging moment", J. Constr. Steel Res., 118, 156-168. https://doi.org/10.1016/j.jcsr.2015.11.008.
  9. Barbosa, W.C.S. (2016), "Study of steel rebar shear connector for steel-concrete composite beams", Ph.D. Thesis Dissertation, The University of Brasilia, Brasilia (In Portuguese).
  10. Bezerra, L.M., Barbosa, W.C.S., Bonilla, J. and Cavalcante, O.R.O. (2018), "Truss-type shear connector for composite steel-concrete beams", Constr. Build. Mater., 167, 757-767. https://doi.org/10.1016/j.conbuildmat.2018.01.183.
  11. Bonilla, J., Bezerra, L.M., Mirambell, E. and Massicotte, B. (2018), "Review of stud shear resistance prediction in steel-concrete composite beams", Steel Compos. Struct., 27(3), 355-370. https://doi.org/10.12989/scs.2018.27.3.355.
  12. Candido-Martins, J.P.S., Costa-Neves, L.F. and Vellasco, P.C.G.d. S. (2010), "Experimental evaluation of the structural response of Perfobond shear connectors", Eng. Struct., 32(8), 1976-1985. https://doi.org/10.1016/j.engstruct.2010.02.031.
  13. Cornellissen H., Hordijk D. and Reinhardt, H. (1986), "Experimental determination of crack softening characteristics of normal weight and lightweight concrete", Heron. 31 45-56.
  14. Ellobody, E. and Young, B. (2006), "Performance of shear connection in composite beams with profiled steel sheeting", J. Constr. Steel Res., 62(7), 682-694. https://doi.org/10.1016/j.jcsr.2005.11.004.
  15. Eurocode-4 (2004), Design of Composite Steel and Concrete Structures Part 1.1; European Committee for Standardization, Brussels, Belgium.
  16. fib Model Code 2010, (2012), fib Model Code 2010 Final draft Volume 2, The International Federation for Structural Concrete, Lausanne, Switzerland.
  17. Han, Q., Wang, Y., Xu, J., Xing, Y. and Yang, G. (2017), "Numerical analysis on shear stud in push-out test with crumb rubber concrete", J. Constr. Steel Res., 130, 148-158. https://doi.org/10.1016/j.jcsr.2016.12.008.
  18. Kim S.H., Park, S., Kim, K.S. and Jung, C.Y. (2017), "Generalized formulation for shear resistance on Y-type perfobond rib shear connectors", J. Constr. Steel Res., 128, 245-260. https://doi.org/10.1016/j.jcsr.2016.08.016.
  19. Kim, S.H., Kim, K.S., Park, S., Ahn, J.H. and Lee, M.K. (2016), "Y-type perfobond rib shear connectors subjected to fatigue loading on highway bridges", J. Constr. Steel Res. 122, 445-454. https://doi.org/10.1016/j.jcsr.2016.04.015.
  20. Kratzig, W.B. and Polling R. (2004), "An elasto-plastic damage model for reinforced concrete with minimum number of material parameters", Comput. Struct., 82(15-16), 1201-1215. https://doi.org/10.1016/j.compstruc.2004.03.002.
  21. Lam, D. (2007), "Capacities of headed stud shear connectors in composite steel beams with precast hollowcore slabs", J. Constr. Steel Res., 63(9), 1160-1174. https://doi.org/10.1016/j.jcsr.2006.11.012.
  22. Lam D. and El-Lobody, E. (2005), "Behavior of headed stud shear connectors in composite beam", J. Struct. Eng., 131(1), 96-107. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:1(96).
  23. Lopez-Almansa, F., Alfarah, B. and Oller, S. (2014), "Numerical simulation of RC frame testing with damaged plasticity model comparison with simplified models", Proceedings of the Conference: 2nd European conference on earthquake engineering and seismology, Istanbul, Turkey, August.
  24. Nguyen, H.T. and Kim, S.E. (2009b), "Finite element modeling of push-out tests for large stud shear connectors", J. Constr. Steel Res., 65(10-11), 1909-1920. https://doi.org/10.1016/j.jcsr.2009.06.010.
  25. Oller S. (1988), "A Continuous damage model for frictional materials". Ph.D. Thesis Dissertation. Technical University of Catalonia, Barcelona.
  26. Ollgaard, J.G., Slutter, R.G. and Fisher, J.W. (1971), "Shear Strength of Stud Connectors in Lightweight and Normal-Weight Concrete", Eng. J. AISC, 8(2), 55-64.
  27. Paknahad, M., Shariati, M., Sedghi, Y., Bazzaz, M. and Khorami, M. (2018), "Shear capacity equation for channel shear connectors in steel-concrete composite beams", Steel Compos. Struct., 28(4), 483-494. https://doi.org/10.12989/scs.2018.28.4.483.
  28. Pavlovic, M., Markovic, Z., Veljkovic, M. and Buđevac, D. (2013), "Bolted shear connectors vs. headed studs behaviour in push-out tests", J. Constr. Steel Res., 88, 134-149. https://doi.org/10.1016/j.jcsr.2013.05.003.
  29. Qi, J., Wang, J., Li, M. and Chen, L. (2017), "Shear capacity of stud shear connectors with initial damage: Experiment, FEM model and theoretical formulation", Steel Compos. Struct., 25(1), 79-92. https://doi.org/10.12989/scs.2017.25.1.079.
  30. Qureshi, J. and Lam, D. (2012), "Behaviour of headed shear stud in composite beams with profiled metal decking", Adv. Struct. Eng., 15(9), 1547-1558. https://doi.org/10.1260/1369-4332.15.9.1547.
  31. Qureshi, J., Lam, D. and Ye, J. (2011), "The influence of profiled sheeting thickness and shear connector's position on strength and ductility of headed shear connector", Eng. Struct., 33(5), 1643-1656. https://doi.org/10.1016/j.engstruct.2011.01.035.
  32. Shariati, M., Ramli Sulong, N.H., Shariati A. and Khanouki, M.A. (2016), "Behavior of V-shaped angle shear connectors: experimental and parametric study", Mater. Struct., 49(9), 3909-3926. https://doi.org/10.1617/s11527-015-0762-8.
  33. Turmo, J., Lozano-Galant, J. A., Mirambell, E. and Xu, D. (2015), "Modeling composite beams with partial interaction", J. Constr. Steel Res., 114, 380-393. https://doi.org/10.1016/j.jcsr.2015.07.007.
  34. Verissimo, G.S., Paes, J.L.R., Valente, I., Cruz, P.J.S. and Fakury, R.H. (2006), "Design and experimental analysis of a new shear connector for steel and concrete composite structures", Proceedings of the 3rd Int. Conf. Bridg. Maintenance, Saf. and Manag., Porto, Portugal, July.
  35. Xing, Y., Han, Q., Xu, J., Guo, Q. and Wang, Y. (2016), "Experimental and numerical study on static behavior of elastic concrete-steel composite beams", J. Constr. Steel Res., 123, 79-92. https://doi.org/10.1016/j.jcsr.2016.04.023.
  36. Xu, X., Liu, Y. and He, J. (2014), "Study on mechanical behavior of rubber-sleeved studs for steel and concrete composite structures", Constr. Build. Mater., 53, 533-546. https://doi.org/10.1016/j.conbuildmat.2013.12.011.
  37. Zheng, S., Liu, Y., Liu, Y. and Zhao, C. (2019), "Experimental and parametric study on the pull-Out resistance of a notched perfobond shear connector", Appl. Sci., 9(4), 1-20. https://doi.org/10.3390/app9040764.
  38. Zona, A. and Ranzi, G. (2014), "Shear connection slip demand in composite steel-concrete beams with solid slabs", J. Constr.Steel Res., 102, 266-281. https://doi.org/10.1016/j.jcsr.2014.07.018.