Computers and Concrete

  • 제26권1호
  • /
  • Pages.1-10
  • /
  • 2020
  • /
  • 1598-8198(pISSN)
  • /
  • 1598-818X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Minimum cost design of RCMRFs based on consistent approximation method

  • 투고 : 2019.06.28
  • 심사 : 2020.03.31
  • 발행 : 2020.07.25
⟨ 이전 논문 다음 논문 ⟩

초록

In this paper, a procedure for automated optimized design of reinforced concrete frames has been presented. The procedure consists of formulation and solution of the design problem in the form of an optimization problem. The minimization of total cost of R/C frame has been taken as the objective of optimization problem. In this research, consistent approximation method is applied to explicitly formulate constraints and objective function in terms of the design variables. In the presented method, the primary optimization problem is replaced with a sequence of explicit sub-problems. Each sub-problem is efficiently solved using the Sequential Quadratic Programming (SQP) method. The proposed method is demonstrated through a four-story frame and an eight-story frame, and the optimum results are compared with those in the available literature. It is shown that the proposed method can be easily applied to obtain rational, reliable, economical and practical designs for Reinforced Concrete Moment Resisting Frames (RCMRFs) while it is converged after a few analyses.

키워드

참고문헌

  1. ACI 318-08 (2008), Building Code Requirements for Structural Concrete and Commentary-ACI 318R-08, American Concrete Institute, Framing Hills, MI, USA.
  2. Booz, W., Legewie, G. and Thierauf, G. (1984), "Optimization of reinforced concrete structures according to germa design regulations", Proceedings of the International Conference on Computer Aided Analysis and Design of concrete structures, Yugoslavia, October.
  3. Cohn, M.Z. (1968), "Limit design of reinforced concrete frames", J. Struct. Div., ASCE, ST10, 2467-2483. https://doi.org/10.1061/JSDEAG.0002099
  4. Fadaee, M.J. (1996), "Design optimization of three dimensional reinforced concrete structures", Ph.D. Dissertation, University of Waterloo, Waterloo.
  5. Fatma, A.A. (2014), "Multi-objective genetic optimization for scheduling a multi-storey building", Autom. Construct., 44, 119-128. http://dx.doi.org/10.21608/ICCAE.2014.44187.
  6. Franca, M.B.B., Greco, M., Lanes, R.M. and Almeida, V.S. (2016), "Topological optimization procedure considering nonlinear material behavior for reinforced concrete designs", Comput. Concrete, 17(1), 141-156. http://dx.doi.org/10.12989/cac.2016.17.1.141.
  7. Grierson, D.E. (1968), "Optimal design of reinforced concrete frames", Ph.D. Thesis, University of Waterloo, Waterloo, Canada.
  8. Guerra, A. and Kiousis, P.D. (2006), "Design optimization of reinforced concrete structures", Comput. Concrete, 3(5), 313-334. https://doi.org/10.12989/cac.2006.3.5.313.
  9. Guilherme, F.M. and Moacir, K. (2017), "Modified harmony search and its application to cost minimization of RC columns", Adv. Comput. Des., 2(1), 1-13. https://doi.org/10.12989/acd.2017.2.1.001.
  10. Habibi, A., Ghawami, F. and Shahidzadeh, M.S. (2016), "Development of optimum design curves for reinforced concrete beams based on the INBR9", Comput. Concrete, 18(5), 983-998. http://dx.doi.org/10.12989/cac.2016.18.5.983.
  11. Habibi, A., Shahryari, M. and Rostami, H. (2017), "Optimum design of RCMRFs using consistent approximation method", Civil Eng., 33-2(2.1), 127-134. (in Persian)
  12. Habibi, A.R. (2012), "New approximation method for structural optimization", J. Comput. Civil Eng., ASCE, 26(2), 236-247. https://doi.org/10.1061/(ASCE)CP.1943-5487.0000133.
  13. Kanagasundaram, S. and Karihaloo, B.L. (1990), "Minimum cost design of reinforced concrete structures", Struct. Optim., 2(3), 173-184. https://doi.org/10.1007/BF01836566.
  14. Kaveh, A. and Bakhshpoori, T. (2016), "An efficient multi-objective cuckoo search algorithm for design optimization", Adv. Comput. Des., 1(1), 87-103. https://doi.org/10.12989/acd.2016.1.1.087.
  15. Kaveh, A. and Sabzi, O. (2011), "A comparative study of two meta-heuristic algorithms for optimum design of reinforced concrete frames", Int. J. Civil Eng., 9(3), 193-206.
  16. Khaledy, N., Habibi, A. and Memarzadeh, P. (2018), "A comparison between different techniques for optimum design of steel frames subjected to blast", Latin Am. J. Solid. Struct., 15(9), 1-26. https://doi.org/10.1590/1679-78254952.
  17. Kwak, H.G. and Kim, J. (2009), "An integrated genetic algorithm complemented with direct search for optimum design of RC frames", Comput. Aid. Des., 41, 490-500. https://doi.org/10.1016/j.cad.2009.03.005.
  18. Leps, M., Zeman, J. and Bittnar, Z. (2002), "Hybrid optimization approach to design of reinforced concrete frames", Proceedings of the Third International Conference on Engineering Computational Technology, Stirling, Scotland, September.
  19. Lopez, A. and Cruz, F. (2004), "Design of reinforced concrete frames wit damage control", Eng. Struct., 26, 2037-2045. https://doi.org/10.1016/j.engstruct.2004.01.002.
  20. Moharrami, H. (1993), "Design optimization of reinforced concrete building frameworks", Ph.D. Dissertation, University of Waterloo, Waterloo.
  21. Ozbay, E., Oztas, A. and Baykasoglu, A. (2010), "Cost optimization of high strength concretes by soft computing techniques", Comput. Concrete, 7(3), 221-237. https://doi.org/10.12989/cac.2010.7.3.221.
  22. Rahmanian, I., Lucet, Y. and Tesfamariam, S. (2014), "Optimal design of reinforced concrete beams: A review", Comput. Concrete, 13(4), 457-482. https://doi.org/10.12989/cac.2014.13.4.457.
  23. Rajeev, S. and Krishnamoorthy, C.S. (1998), "Genetic algorithm-based methodology for design optimization of reinforced concrete frames", Comput. Aid. Civil Infrastr. Eng., 13(1), 63-74. https://doi.org/10.1111/0885-9507.00086.
  24. Saka, M.P. (1992), "Optimum design of multistory structures with shear walls", Comput. Struct., 44(4), 925-936. https://doi.org/10.1016/0045-7949(92)90480-N.
  25. Serpik, I.N., Mironenko, I.V. and Averchenkov, V.I. (2016), "Algorithm for evolutionary optimization of reinforced concrete frames subject to nonlinear material deformation", Procedia Eng., 150, 1311-1316. https://doi.org/10.1016/0045-7949(92)90480-N.
  26. Shunmagavel, P. (1974), "Optimization of two-dimensional reinforced concrete building frames", Ph.D. Dissertation, University of Illinois at Urbana, Champaign.
  27. Sikiotis, E.S. and Saoma, V.E. (1987), "Optimum design of reinforced concrete frames using interactive computer graphics", Eng. Comput., 3, 101-110. https://doi.org/10.1016/0045-7949(92)90480-N.
  28. Spires, D. and Arora, J.S. (1990), "Optimal design of tall RC-framed tube buildings", J. Struct. Eng., 116(4), 877-897. https://doi.org/10.1061/(ASCE)0733-9445(1990)116:4(877).
  29. Yang, M.F. (1982), "Optimization of reinforced concrete structures", Ph.D. Dissertation, University of Illinois, Urbana-Champaign.