Structural Engineering and Mechanics

  • 제74권5호
  • /
  • Pages.657-670
  • /
  • 2020
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Experimental studies of headed stud shear connectors in UHPC Steel composite slabs

  • Gao, Xiao-Long (Key Laboratory of Advanced Civil Engineering Materials, Tongji University, Ministry of Education) ;
  • Wang, Jun-Yan (Key Laboratory of Advanced Civil Engineering Materials, Tongji University, Ministry of Education) ;
  • Yan, Jia-Bao (School of Civil Engineering, Tianjin University)
  • 투고 : 2019.11.04
  • 심사 : 2020.01.21
  • 발행 : 2020.06.10
⟨ 이전 논문 다음 논문 ⟩

초록

Due to the high compressive and tensile strength of ultra-high performance concrete (UHPC), UHPC used in steel concrete composite structures provided thinner concrete layer compared to ordinary concrete. This leaded to the headed stud shear connectors embedded in UHPC had a low aspect ratio. In order to systematic investigate the effect of headed stud with low aspect ratio on the structural behaviors of steel UHPC composite structure s this paper firstly carried out a test program consisted of twelve push out specimens. The effects of stud height, aspect ratio and reinforcement bars in UHPC on the structural behaviors of headed studs were investigated. The push out test results shows that the increasing of stud height did not obviously influence the structural behaviors of headed studs and the aspect ratio of 2.16 was proved enough to take full advantage of the headed stud strength. Based on the test results, the equation considering the contribution of weld collar was modified to predict the shear strength of headed stud embedded in UHPC. The modified equation could accurately predict the shear strength of headed stud by comparing with the experimental results. On the basis of push out test results, bending tests consisted of three steel UHPC composite slabs were conducted to investigate the effect of shear connection degree on the structural behaviors of composite slabs. The bending test results revealed that the shear connection degree had a significantly influence on the failure modes and ultimate resistance of composite slabs and composite slab with connection degree of 96% in s hear span exhibited a ductile failure accompanied by the tensile yield of steel plate and crushing of UHPC. Finally, analytical model based on the failure mode of composite slabs was proposed to predict the ultimate resistance of steel UHPC composite slabs with different shear connection degrees at the interface.

키워드

과제정보

This work was supported by Zhejiang Communication Science and Technology Project [grant number 2019-GCKY-01], the National Nature Science Foundation of China [grant number 51609172] and the Shanghai Municipal Science and Technology Project [grant number 17DZ1204200]. The financial supports are greatly appreciated.

참고문헌

  1. AASHTO(2012), AASHTO LRFD Bridge Design Specifications, American Association of State Highway and Transportation Officials; Washington DC, United States.
  2. An, L. and Cederwall, K. (1996), "Push-out tests on studs in high strength and normal strength concrete", J. Constr. Steel. Res., 36(1), 15-29. https://doi.org/10.1016/0143-974X(94)00036-H.
  3. ASTM A370-13 (2013), Standard Test Methods and Definitions for Mechanical Testing of Steel Products. ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2949, United States.
  4. Cao, J.H., Shao, X.D., Deng, L. and Gan, Y.D. (2017), "Static and fatigue behavior of short-headed studs embedded in a thin ultrahigh-performance concrete layer", J. Bridge. Eng., 22(5), 04017005. https://doi.10.1061/(ASCE)BE.1943-5592.0001031.
  5. Cao, J.H., Shao, X.D. (2019), "Finite element analysis of headed studs embedded in thin UHPC", J. Constr. Steel. Res., 161(7), 355-368. https://doi.org/10.1016/j.jcsr.2019.03.016.
  6. Dieng, L., Marchand, P., Gomes, F., Terrier, C. and Toutlemonde, F. (2013), "Use of UHPFRC overlay to reduce stresses in orthotropic steel decks", J. Constr. Steel. Res., 89(10), 30-41. https://doi.org/10.1016/j.jcsr.2013.06.006.
  7. Doinghaus, P., Goralski, C. and Will, N. (2003), "Design rules for composite structures with high performance steel and high performance concrete", International Conference on High Performance Materials in Bridges, Kona, HI, July.
  8. Eurocode 4(2005), Design of composite steel and concrete structures. Part 2: General rules for bridges, European Committee for Standardization; London, Britain.
  9. GB/T 10433-2002 (2002), Cheese head studs for arc stud welding, Inspection and Quarantine of the People's Republic of China; Beijing, Chinese. (in Chinese).
  10. Habel, K., Denarie, E. and Bruhwiler, E. (2007), "Experimental investigation of composite ultra-high-performance fiber-reinforced concrete and conventional concrete members", ACI. Struct. J., 104(1), 93-104. http://orcid.org/0000-0002-2588-432X.
  11. Hadji, L., Ait Amar Meziane, M., and Safa, A., (2018), "A new quasi-3D higher shear deformation theory for vibration of functionally graded carbon nanotube-reinforced composite beams resting on elastic foundation", Struct. Eng. Mech., 66(6), 771-781. https://doi.org/10.12989/sem.2018.66.6.771.
  12. Hadji, L., Hassaine Daouadji, T., Ait Amar Meziane, M., and Adda Bedia, E.A. (2016), "Analyze of the interfacial stress in reinforced concrete beams strengthened with externally bonded CFRP plate", Steel. Compos. Struct., 20(2), 413-429. https://doi.org/10.12989/scs.2016.20.2.413.
  13. Hamoda, A., Hossain, K.M.A., Sennah, K., Shoukry, M. and Mahmoud, Z. (2017), "Behaviour of composite high performance concrete slab on steel I-beams subjected to static hogging moment", Eng. Struct., 140(6), 51-65. https://doi.org/10.1016/j.engstruct.2017.02.030.
  14. Hassaine Daouadji, T., Hadji, L., Ait Amar Meziane, M., and Bekki, H., (2016), "Elastic analysis effect of adhesive layer characteristics in steel beam strengthened with a fiber-reinforced polymer plates", Struct. Eng. Mech., 59(1), 83-100. https://doi.org/10.12989/sem.2016.59.1.083.
  15. Hoang, A.L. and Fehling, E. (2017a), "A review and analysis of circular UHPC filled steel tube columns under axial loading", Struct. Eng. Mech., 62(4), 417-430. https://doi.org/10.12989/sem.2017.63.3.371.
  16. Hoang, A.L. and Fehling, E. (2017b), "Assessment of stress-strain model for UHPC confined by steel tube stub columns", Struct. Eng. Mech., 63(3), 371-384. https://doi.org/10.12989/sem.2017.63.3.371.
  17. Kang, S.T., Lee, Y., Park, Y.D. and Kim, J.K. (2010), "Tensile fracture properties of an Ultra High Performance Fiber Reinforced Concrete (UHPFRC) with steel fiber", Compos. Struct., 92(1), 61-71. https://doi.org/10.1016/j.compstruct.2009.06.012.
  18. Khelifa, Z., Hadji, L., Hassaine Daouadji, T. and Bourada, M., (2018), "Buckling response with stretching effect of carbon nanotube-reinforced composite beams resting on elastic foundation", Struct. Eng. Mech., 67(2), 125-130. https://doi.org/10.12989/sem.2018.67.2.125.
  19. Kim, J.S., Kwark, J., Joh, C., Yoo, S.W. and Lee, K.C. (2015), "Headed stud shear connector for thin ultrahigh-performance concrete bridge deck", J. Constr. Steel. Res., 108(5), 23-30. https://doi.org/10.1016/j.jcsr.2015.02.001.
  20. Lampropoulos, A., Paschalis, S.A., Tsioulou, O. and Dritsos, S.E. (2016), "Strengthening of reinforced concrete beams using ultra high performance fibre reinforced concrete (UHPFRC)", Eng. Struct., 106(11), 370-384. https://doi.org/10.1016/j.engstruct.2015.10.042.
  21. Lin, Y.Z., Yan, J.C., Cao, Z.G., Zeng, X.Z., Fan, F. and Zou, C.Y. (2018), "Ultimate strength behaviour of S-UHPC-S and SCS sandwich beams under shear loads", J. Constr. Steel. Res., 149(10), 195-206. https://doi.org/10.1016/j.jcsr.2018.07.024.
  22. Liu, Y.M., Zhang, Q.H., Bao, Y. and Bu, Y.Z. (2019), "Static and fatigue push-out tests of short headed shear studs embedded in Engineered Cementitious Composites (ECC)", Eng. Struct., 182(3), 29-38. https://doi.org/10.1016/j.engstruct.2018.12.068.
  23. Liu, Y.M., Zhang, Q.H., Meng, W.N., Bao, Y. and Bu, Y.Z. (2019), "Transverse fatigue behaviour of steel-UHPC composite deck with large-size U-ribs", Eng. Struct., 180(2), 370-384. https://doi.org/10.1016/j.engstruct.2018.11.057.
  24. Luo, J., Shao, X.D., Fan, W., Cao, J.H. and Deng, S.W. (2019), "Flexural cracking behavior and crack width predictions of composite (steel+UHPC) lightweight deck system", Eng. Struct., 194(1), 120-137. https://doi.org/10.1016/j.engstruct.2019.05.018.
  25. Luo, Y.B., Hoki, K., Hayashi, K. and Nakashima, M. (2016), "Behavior and strength of headed stud-SFRCC shear connection. II: Strength Evaluation", J. Struct. Eng., 142(2), 04015113. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001372.
  26. Ollgaard, J.G., Slutter, R.G. and Fisher, J.W. (1971), "Shear strength of stud connectors in light weight and normal-weight concrete", AISC. Eng. J., 8(2), 55-64. https://preserve.lehigh.edu/engr-civil-environmental-fritz-lab-reports/2010.
  27. Prem, P. R., Verma, M., Ramachandra, M. A., Rajasankar, J. and Bharatkumar, B.H. (2017), "Numerical and theoretical modelling of low velocity impact on UHPC panels" , Struct. Eng. Mech., 63(2), 207-215. https://doi.org/10.12989/sem.2017.63.2.207.
  28. Shao, X.D., Yi, D., Huang, Z., Zhao, H., Chen, B. and Liu, M. (2013), "Basic performance of the composite deck system composed of orthotropic steel deck and ultrathin RPC layer", J. Bridge. Eng., 18(5), 417-428. https://10.1061/(ASCE)BE.1943-5592.0000348.
  29. Sun, Q.L., Lu, X.Y., Nie, X., Han, Z.J. and Fan, J.S. (2017), "Experimental research on tensile and shear behaviour of the interface between non-steam-cured uhpc and steel plate structure", Eng. Mech., 34(9), 167-174.(in Chinese).
  30. Wang, J.Q., Qi, J.N., Tong, T., Xu, Q.Z. and Xiu, H.L. (2019), "Static behavior of large stud shear connectors in steel-UHPC composite structures", Eng. Struct., 178(1), 534-542. https://doi.org/10.1016/j.engstruct.2018.07.058.
  31. Wang, J.Q., Xu, Q.Z., Yao, Y.M., Qi, J.N. and Xiu, H.L. (2018), "Static behavior of grouped large headed stud-UHPC shear connectors in composite structures", Compos. Struct., 206(15),202-214. https://doi.org/10.1016/j.compstruct.2018.08.038.1
  32. Wang, J.Y., Gao, X.L. and Yan, J.B. (2019), "Behaviours of steel-fibre-reinforced ULCC slabs subject to concentrated loading", Struct. Eng. Mech., 71(4), 407-416. https://doi.org/10.12989/sem.2019.71.4.407.
  33. Wang, J.Y. and Guo, J.Y. (2018), "Damage investigation of ultra high performance concrete under direct tensile test using acoustic emission techniques", Cem. Concr. Compos., 88(4), 17-28. https://doi.org/10.1016/j.cemconcomp.2018.01.007.
  34. Wang, J.Y., Guo, J.Y., Jia, L.J., Chen, S.M. and Dong, Y. (2017), "Push-out tests of demountable headed stud shear connectors in steel-UHPC composite structures", Compos. Struct., 170(6), 69-79. https://doi.org/10.1016/j.compstruct.2017.03.004.
  35. Wang, Z., Nie, X., Fan, J.S., Lu, X.Y. and Ding, R. (2019), "Experimental and numerical investigation of the interfacial properties ofnon-steam-cured UHPC-steel composite beams", Constr. Build. Mater., 195(1), 323-39. https://doi.org/10.1016/j.conbuildmat.2018.11.057.
  36. Yin, H., Teo, W. and Shirai, K. (2017), "Experimental investigation on the behaviour of reinforced concrete slabs strengthened with ultra-high performance concrete", Constr. Build. Mater., 155(30), 463-474. https://doi.org/10.1016/j.conbuildmat.2017.08.077.
  37. Yoo, D.Y., Banthia, N., Kim, S.W. and Yoon Y.S. (2015), "Response of ultra-high-performance fiber reinforced concrete beams with continuous steel reinforcement subjected to low velocity impact loading", Compos. Struct., 126(8), 233-45. https://doi.org/10.1016/j.compstruct.2015.02.058.
  38. Yoo, D.Y., Kwon, K.Y., Park, J.J. and Yoon, Y.S. (2015), "Local bond-slip response of GFRP rebar in ultra-high-performance fiber-reinforced concrete", Compos. Struct., 120(2), 53-64. https://doi.org/10.1016/j.compstruct.2014.09.055.
  39. Zhang, S.H., Shao, X.D., Cao, J.H., Cui, J.F., Hu, J.H. and Deng, L. (2016), "Fatigue performance of a lightweight composite bridge deck with open ribs", J. Bridge. Eng., 21(7), 04016039. https://10.1061/(ASCE)BE.1943-5592.0000905.