Steel and Composite Structures

  • 제35권4호
  • /
  • Pages.463-474
  • /
  • 2020
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Bond behavior between steel and Glass Fiber Reinforced Polymer (GFRP) bars and ultra high performance concrete reinforced by Multi-Walled Carbon Nanotube (MWCNT)

  • 투고 : 2019.07.30
  • 심사 : 2020.03.05
  • 발행 : 2020.05.25
⟨ 이전 논문 다음 논문 ⟩

초록

In this paper, the influence of adding multi-walled carbon nanotube (MWCNT) on the pull behavior of steel and GFRP bars in ultra-high-performance concrete (UHPC) was examined experimentally and numerically. For numerical analysis, 3D nonlinear finite element modeling (FEM) with the help of ABAQUS software was used. Mechanical properties of the specimens, including Young's modulus, tensile strength and compressive strength, were extracted from the experimental results of the tests performed on standard cube specimens and for different values of weight percent of MWCNTs. In order to consider more realistic assumptions, the bond between concrete and bar was simulated using adhesive surfaces and Cohesive Zone Model (CZM), whose parameters were obtained by calibrating the results of the finite element model with the experimental results of pullout tests. The accuracy of the results of the finite element model was proved with conducting the pullout experimental test which showed high accuracy of the proposed model. Then, the effect of different parameters such as the material of bar, the diameter of the bar, as well as the weight percent of MWCNT on the bond behavior of bar and UHPC were studied. The results suggest that modifying UHPC with MWCNT improves bond strength between concrete and bar. In MWCNT per 0.01 and 0.3 wt% of MWCNT, the maximum pullout strength of steel bar with a diameter of 16 mm increased by 52.5% and 58.7% compared to the control specimen (UHPC without nanoparticle). Also, this increase in GFRP bars with a diameter of 16 mm was 34.3% and 45%.

키워드

참고문헌

  1. Azim, R. and Amiri G., (2016), "The effects of near and far fault accelerograms modification on seismic behaviour of concentrated braced steel frames", J. Res. Sci., Eng. Technol., 4(1), 12-21.
  2. Bhargava, K., Ghosh, A., Mori, Y. and Ramanujam, S. (2007), "Corrosion-induced bond strength degradation in reinforced concrete-Analytical and empirical models", Nuclear Eng. Design, 237(11), 1140-1157. https://doi.org/10.1016/j.nucengdes.2007.01.010.
  3. Chupin, O., Piau, J.M., Hammoum, F. and Bouron, S. (2018), "Experimental study and modeling of the behavior of partially saturated asphalt concrete under freezing condition", Constr. Build. Mater., 163, 169-178. https://doi.org/10.1016/j.conbuildmat.2017.12.070.
  4. Committee, A. (2006), "Guide for the Design and Construction of Concrete Reinforced with FRP Bars (ACI 440.1 R-06)", American Concrete Institute, Detroit, Michigan.
  5. Dehestani, M., Asadi, A. and Mousavi, S. (2017), "On discrete element method for rebar-concrete interaction", Constr. Build. Mater., 151, 220-227. https://doi.org/10.1016/j.conbuildmat.2017.06.086.
  6. Hung, C.C., Lee, H.S. and Chan,S.N. (2019), "Tension-stiffening effect in steel-reinforced UHPC composites: Constitutive model and effects of steel fibers, loading patterns, and rebar sizes", Compos. Part B: Eng., 158, 269-278. https://doi.org/10.1016/j.compositesb.2018.09.091.
  7. Jankovic, K., Bojovic, D. and Stojanovic, M.(2019), 2 - Influence of nanoparticles on the strength of ultra-high performance concrete, in Nanotechnology in Eco-efficient Construction (Second Edition), (Eds., F. Pacheco-Torgal, M.V. Diamanti, A. Nazari, C.G. Granqvist, A. Pruna, and S. Amirkhanian), Woodhead Publishing, 13-42.
  8. Kazim, T. (2014), "Bond strength of tension lap-splices in full scale self-compacting concrete beams", Turkish J. Eng.and Environ. Sci.. 32(6), 377-386.
  9. Konsta-Gdoutos, M.S., Metaxa, Z.S. and Shah, S.P. (2010), "Highly dispersed carbon nanotube reinforced cement based materials", Cement Concrete Res., 40(7), 1052-1059. https://doi.org/10.1016/j.cemconres.2010.02.015.
  10. Kowald, T. (2008), Influence of Carbon Nanotubes on the micromechanical properties of a model system for ultra-high performance concrete, 2nd International Symposium on Ultra High Performance Concrete, USA.
  11. Le, A.H., Ekkehard, F., Thai, D.K. and Nguyen, C.V. (2018), "Simplified stress-strain model for circular steel tube confined UHPC and UHPFRC columns", Steel Compos. Struct., 29(1), 125-138. https://doi.org/10.12989/scs.2018.29.1.125.
  12. Lim, N.H.A.S. (2018), "Microstructure and strength properties of mortar containing waste ceramic nanoparticles", Arabian J. Sci. Eng., 43(10), 5305-5313. https://doi.org/10.1007/s13369-018-3154-x
  13. Liu, X., Chen, L., Liu, A. and Wang, X. (2012), "Effect of nano-CaCO3 on properties of cement paste", Energy Procedia, 16, 991-996. https://doi.org/10.1016/j.egypro.2012.01.158.
  14. Liu, X.F. (2020), Mechanical Properties of Nano-Particle Modified Ultra-High Performance Fiber Reinforced Concrete. in ACMSM25, Singapore: Springer Singapore.
  15. Lu, Y., Liu, Z., Li, S. and Li, N. (2018), "Bond behavior of steel fibers reinforced self-stressing and self-compacting concrete filled steel tube columns", Constr. Build. Mater., 158, 894-909. https://doi.org/10.1016/j.conbuildmat.2017.10.085.
  16. Meng, W. and Khayat, K.H. (2016), "Experimental and numerical studies on flexural behavior of ultrahigh-performance concrete panels reinforced with embedded glass fiber-reinforced Polymer grids", Transportation Research Record, 2592(1), 38-44. https://doi.org/10.3141/2592-05.
  17. Midhuna, M.S., Gunneswara, T.D. and Chaitanya Srikrishna, T. (2018), "Mechanical and fracture properties of glass fiber reinforced geopolymer concrete", Adv. Concrete Constr., 6(1), 29-45. https://doi.org/10.12989/acc.2018.6.1.029.
  18. Michal, M. and Keuser, M. (2018), Bond Tests Under High Loading Rates, in High Tech Concrete: Where Technology and Engineering Meet, 1453-1461.
  19. Mosaberpanah, M.A., Eren, O. and Tarassoly, A.R. (2019), "The effect of nano-silica and waste glass powder on mechanical, rheological, and shrinkage properties of UHPC using response surface methodology", J. Mater. Res. Technol., 8(1), 804-811. https://doi.org/10.1016/j.jmrt.2018.06.011
  20. Mousavi, M.A. and Bahari, A. (2019), "Influence of functionalized MWCNT on microstructure and mechanical properties of cement paste", Sadhana, 44(5), 103. https://doi.org/10.1007/s12046-019-1087-z.
  21. Norhasri, M.S.M., Hamidah, M.S. and Fadzil, A.M. (2017), "Applications of using nano material in concrete: A review", Constr. Build. Mater., 133, 91-97. https://doi.org/10.1016/j.conbuildmat.2016.12.005.
  22. Ozbolt, J., Orsanic, F. and Balabanic, G. (2014), "Modeling pull-out resistance of corroded reinforcement in concrete: Coupled three-dimensional finite element model", Cement Concrete Compos.. 46, 41-55. https://doi.org/10.1016/j.cemconcomp.2013.10.014.
  23. Peyvandi, A., Soroushian, P., Abdol, N. and Balachandra, A.M. (2013), "Surface-modified graphite nanomaterials for improved reinforcement efficiency in cementitious paste", Carbon, 63, 175-186. https://doi.org/10.1016/j.carbon.2013.06.069.
  24. Rezaee, M. and Maleki, V.A. (2015), "An analytical solution for vibration analysis of carbon nanotube conveying viscose fluid embedded in visco-elastic medium", Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 229(4), 644-650. https://doi.org/10.1177/0954406214538011
  25. Shoushtari, A., Sharafi, M. and Sekhavat, S. (2013), "Effect of Solution Annealing Heat Treatment on the Corrosion Resistance and Mechanical Properties of an Austenitic Stainless Steel", Uct J. Res. Sci., Eng. Technol., 1(4), 17-20.
  26. Solomos, G. and Berra, M. (2010), "Rebar pullout testing under dynamic Hopkinson bar induced impulsive loading", Mater. Struct., 43(1-2), 247-260. https://doi.org/10.1617/s11527-009-9485-z.
  27. Unsal, I., Tokgoz, S., Cagatay, I.H. and Dundar, C. (2017), "A study on load-deflection behavior of two-span continuous concrete beams reinforced with GFRP and steel bars", Struct. Eng. Mech., 63(5) 629-637. https://doi.org/10.12989/sem.2017.63.5.629.
  28. Veljkovic, A., Carvelli, V., Haffke, M.M. and Pahn, M. (2017), "Concrete cover effect on the bond of GFRP bar and concrete under static loading", Compos. Part B: Eng., 124, 40-53. https://doi.org/10.1016/j.compositesb.2017.05.054.
  29. Vilanova, I., Baena, M., Torres, L. and Barris, C. (2015), "Experimental study of bond-slip of GFRP bars in concrete under sustained loads", Compos. Part B: Eng., 74, 42-52. https://doi.org/10.1016/j.compositesb.2015.01.006.
  30. Wu, Z., Khayat, K.H. and Shi, C. (2017), "Effect of nano-SiO2 particles and curing time on development of fiber-matrix bond properties and microstructure of ultra-high strength concrete", Cement Concrete Res., 95, 247-256. https://doi.org/10.1016/j.cemconres.2017.02.031.
  31. Wu, Z., Shi, C. and Khayat, K.H. (2018), "Multi-scale investigation of microstructure, fiber pullout behavior, and mechanical properties of ultra-high performance concrete with nano-CaCO3 particles", Cement Concrete Compos., 86, 255-265. https://doi.org/10.1016/j.cemconcomp.2017.11.014
  32. Yan, F. (2017), "Experimental study on bond durability of glass fiber reinforced polymer bars in concrete exposed to harsh environmental agents: freeze-thaw cycles and alkaline-saline solution", Compos. Part B: Eng., 116, 406-421. https://doi.org/10.1016/j.compositesb.2016.10.083.
  33. Yoo, D.Y., Kang, S.T., Banthia, N. and Yoon, Y.S. (2017), "Nonlinear finite element analysis of ultra-high-performance fiber-reinforced concrete beams", Int. J. Damage Mech., 26(5), 735-757. https://doi.org/10.1177/1056789515612559.
  34. Madanipour, V., Montazeri-Gh, M. and Mahmoodi-k, M. (2016), "Optimization of the component sizing for a plug-in hybrid electric vehicle using a genetic algorithm", Proceedings of the Institution of Mechanical Engineers, Part D: J. Automobile Eng., 230(5), 692-708. https://doi.org/10.1177/0954407015592256
  35. Zhang, H., Ji, T. and Lin, X. (2019), "Pullout behavior of steel fibers with different shapes from ultra-high performance concrete (UHPC) prepared with granite powder under different curing conditions", Constr. Build. Mater., 211, 688-702. https://doi.org/10.1016/j.conbuildmat.2019.03.274.
  36. Zhang, X., Ou, J. and Wu, Z. (2017), "Effect of circumferentially nonuniform lateral tension on bond behavior between plain round bars and concrete: Analytical study", J. Struct. Eng., 143(12), 34-54.
  37. Ziaei-Nia, A., Shariati, M. and Salehabadi, E. (2018), "Dynamic mix design optimization of high-performance concrete", Steel Compos. Struct., 29(1), 67-75. https://doi.org/10.12989/scs.2018.29.1.067.
  38. Zong-cai, D., Daud, J.R. and Chang-xing, Y. (2014), "Bonding between high strength rebar and reactive powder concrete", Comput. Concrete, 13(3), 411-421. http://dx.doi.org/10.12989/cac.2014.13.3.411.

피인용 문헌

  1. Tensile-Shear Mechanical Behaviors of Friction Stir Spot Weld and Adhesive Hybrid Joint: Experimental and Numerical Study vol.10, pp.8, 2020, https://doi.org/10.3390/met10081028