Steel and Composite Structures

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Experimental study on axial compressive behavior of welded built-up CFT stub columns made by cold-formed sections with different welding lines

  • Naghipour, Morteza (Department of Civil, Babol Noshirvani University of Technology) ;
  • Yousofizinsaz, Ghazaleh (Department of Civil, Babol Noshirvani University of Technology) ;
  • Shariati, Mahdi (Division of Computational Mathematics and Engineering, Institute for Computational Science, Ton Duc Thang University)
  • Received : 2019.04.13
  • Accepted : 2019.11.01
  • Published : 2020.02.25
⟨ Previous Next ⟩

Abstract

The objective of this study is to experimentally scrutinize the axial performance of built-up concrete filled steel tube (CFT) columns composed of steel plates. In this case, the main parameters cross section types, compressive strength of filled concrete, and the effect of welding lines. Welded built-up steel box columns are fabricated by connecting two pieces of cold-formed U-shaped or four pieces of L-shaped thin steel plates with continuous penetration groove welding line located at mid-depth of stub column section. Furthermore, traditional square steel box sections with no welding lines are investigated for the comparison of axial behavior between the generic and build-up cross sections. Accordingly, 20 stub columns with thickness and height of 2 and 300 mm have been manufactured. As a result, welding lines in built-up specimens act as stiffeners because have higher strength and thickness in comparison to the plates. Subsequently, by increasing the welding lines, the load bearing capacity of stub columns has been increased in comparison to the traditional series. Furthermore, for specimens with the same confinement steel tubes and concrete core, increment of B/t ratio has reduced the ductility and axial strength.

Keywords

Acknowledgement

Supported by : Babol Noshirvani University of Technology

The research presented in this paper was supported by Babol Noshirvani University of Technology (Award No: BNUT934140052). The support is gratefully acknowledged.

References

  1. Abed, F., et al. (2013), "Experimental and numerical investigations of the compressive behavior of concrete filled steel tubes (CFSTs)", J. Constr. Steel Res., 80, 429-439. https://doi.org/10.1016/j.jcsr.2012.10.005.
  2. Arabnejad Khanouki, M., et al. (2010), "Investigation of seismic behaviour of composite structures with concrete filled square steel tubular (CFSST) column by push-over and time-history analyses", Proceedings of the 4th International Conference on Steel & Composite Structures.
  3. Bakis, C.E., et al. (2002), "Fiber-reinforced polymer composites for construction-State-of-the-art review", J. Compos. Constr., 6(2), 73-87. https://doi.org/10.1061/(ASCE)1090-0268(2002)6:2(73).
  4. Chen, C., et al. (2019), "Behavior of steel storage pallet racking connection-A review", Steel Compos. Struct., 30(5), 457-469. https://doi.org/10.12989/scs.2019.30.5.457.
  5. Chitawadagi, M.V., et al. (2010), "Axial strength of circular concrete-filled steel tube columns-DOE approach", J. Constr. Steel Res., 66(10), 1248-1260. https://doi.org/10.1016/j.jcsr.2010.04.006.
  6. Dai, J.G., et al. (2011), "Behavior and modeling of concrete confined with FRP composites of large deformability", J. Compos. Constr., 15(6), 963-973. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000230.
  7. Daie, M., et al. (2011), "A new finite element investigation on pre-bent steel strips as damper for vibration control", Int. J. Phys. Sci., 6(36), 8044-8050. DOI: 10.5897/IJPS11.1585.
  8. Davoodnabi, S.M., et al. (2019), "Behavior of steel-concrete composite beam using angle shear connectors at fire condition", Steel Compos. Struct., 30(2), 141-147. https://doi.org/10.12989/scs.2019.30.2.141.
  9. Evirgen, B., et al. (2014), "Structural behavior of concrete filled steel tubular sections (CFT/CFSt) under axial compression", Thin-Wall. Struct., 80, 46-56. https://doi.org/10.1016/j.tws.2014.02.022.
  10. Fam, A., et al. (2003), "Precast piles for Route 40 bridge in Virginia using concrete filled FRP tubes", PCI J., 48(3), 32-45. https://doi.org/10.15554/pcij.05012003.32.45
  11. Ferhoune, N., et al. (2016), "Behavior of hollow thin welded tubes filled with sand slag concrete", Adv. Mater. Sci. Eng., 2016. http://dx.doi.org/10.1155/2016/5218738.
  12. Gupta, P.K., et al. (2014), "Modelling, verification and investigation of behaviour of circular CFST columns", Struct. Concrete, 15(3), 340-349. DOI: 10.1002/suco.201300045.
  13. Han, L.H., et al. (2010), "Tests on inclined, tapered and STS concrete-filled steel tubular (CFST) stub columns", J. Constr. Steel Res., 66(10), 1186-1195. https://doi.org/10.1016/j.jcsr.2010.03.014.
  14. Han, L.H., et al. (2014), "Developments and advanced applications of concrete-filled steel tubular (CFST) structures: Members", J. Constr. Steel Res., 100, 211-228. https://doi.org/10.1016/j.jcsr.2014.04.016.
  15. Hosseinpour, E., et al. (2018), "Direct shear behavior of concrete filled hollow steel tube shear connector for slim-floor steel beams", Steel Compos. Struct., 26(4), 485-499. https://doi.org/10.12989/scs.2018.26.4.485.
  16. Jalali, A., et al. (2012), "Seismic performance of structures with pre-bent strips as a damper", Int. J. Phys. Sci., 7(26), 4061-4072.
  17. Katebi, J., et al. (2019), "Developed comparative analysis of metaheuristic optimization algorithms for optimal active control of structures", Engineering with Computers, 1-20. https://doi.org/10.1007/s00366-019-00780-7.
  18. Khorami, M., et al. (2017a), "Seismic performance evaluation of buckling restrained braced frames (BRBF) using incremental nonlinear dynamic analysis method (IDA)", Earthq. Struct., 13(6), 1-6. http://dx.doi.org/10.12989/eas.2017.13.6.531.
  19. Khorami, M., et al. (2017b), "Evaluation of the seismic performance of special moment frames using incremental nonlinear dynamic analysis", Struct. Eng. Mech., 63(2), 259-268. http://dx.doi.org/10.12989/sem.2017.63.2.259.
  20. Khorramian, K., et al. (2015), "Behavior of Tilted Angle Shear Connectors", PLoS One, 10(12), e0144288. 10.1371/journal.pone.0144288.
  21. Khorramian, K., et al. (2016), "Behavior of tilted angle shear connectors", PLoS One, 11(2). https://doi.org/10.1371/journal.pone.0148945.
  22. Khorramian, K., et al. (2017), "Numerical analysis of tilted angle shear connectors in steel-concrete composite systems", Steel Compos. Struct., 23(1), 67-85. http://dx.doi.org/10.12989/scs.2017.23.1.067.
  23. Kildashti, K., et al. (2019), "Seismic collapse assessment of a hybrid cold-formed hot-rolled steel building", J. Constr. Steel Res., 155, 504-516. https://doi.org/10.1016/j.jcsr.2019.01.010.
  24. Lee, S., et al. (2011),. "Structural characteristics of welded built-up square concrete filled tubular stub columns associated with concrete strength", Procedia Eng., 14, 1140-1148. https://doi.org/10.1016/j.proeng.2011.07.143.
  25. Li, D., et al. (2019), "Application of polymer, silica-fume and crushed rubber in the production of Pervious concrete", Smat Struct. Syst., 23(2), 207-214. http://dx.doi.org/10.12989/sss.2019.23.2.207.
  26. Luo, Z., et al. (2019), "Computational and experimental analysis of beam to column joints reinforced with CFRP plates", Steel Compos. Struct., 30(3), 271-280. http://dx.doi.org/10.12989/scs.2019.30.3.271.
  27. Mansouri, I., et al. (2019), "Analysis of influential factors for predicting the shear strength of a V-shaped angle shear connector in composite beams using an adaptive neuro-fuzzy technique", J. Intel. Manufact., 30(3), 1-11. https://doi.org/10.1007/s10845-017-1306-6.
  28. Milovancevic, M., et al. (2019), "UML diagrams for dynamical monitoring of rail vehicles", Physica A: Stat. Mech. Appl., 121169.
  29. Mohammadhassani, M., et al. (2014a). "An experimental study on the failure modes of high strength concrete beams with particular references to variation of the tensile reinforcement ratio", Eng. Fail. Anal., 41, 73-80. https://doi.org/10.1016/j.engfailanal.2013.08.014.
  30. Mohammadhassani, M., et al. (2014b), "An evolutionary fuzzy modelling approach and comparison of different methods for shear strength prediction of high-strength concrete beams without stirrups", Smart Struct. Syst., 14(5), 785-809. http://dx.doi.org/10.12989/sss.2014.14.5.785.
  31. Mortazavi, M., et al. (2020), "Prefabricated hybrid steel wall panels for mid-rise construction in seismic regions", J. Build. Eng., 27, 100942. https://doi.org/10.1016/j.jobe.2019.100942.
  32. Nasrollahi, S., et al. (2018), "Investigation of pipe shear connectors using push out test", Steel Compos. Struct., 27(5), 537-543. http://dx.doi.org/10.12989/scs.2018.27.5.537.
  33. Paknahad, M., et al. (2018), "Shear capacity equation for channel shear connectors in steel-concrete composite beams", Steel Compos. Struct., 28(4), 483-494. http://dx.doi.org/10.12989/scs.2018.28.4.483.
  34. Petrus, A. and Alfonsi, P. (2006), Dialogue against the Jews, CUA Press.
  35. Saberian, M., et al. (2018), "Experimental and phenomenological study of the effects of adding shredded tire chips on geotechnical properties of peat", Int. J. Geotech. Eng., 12(4), 347-356. https://doi.org/10.1080/19386362.2016.1277829.
  36. Sadeghipour Chahnasir, E., et al. (2018), "Application of support vector machine with firefly algorithm for investigation of the factors affecting the shear strength of angle shear connectors", Smart Struct. Syst., 22(4), 413-424. http://dx.doi.org/10.12989/sss.2018.22.4.413.
  37. Safa, M., et al. (2016), "Potential of adaptive neuro fuzzy inference system for evaluating the factors affecting steel-concrete composite beam's shear strength", Steel Compos. Struct., 21(3), 679-688. http://dx.doi.org/10.12989/scs.2016.21.3.679.
  38. Sajedi, F. and Shariati, M. (2019), "Behavior study of NC and HSC RCCs confined by GRP casing and CFRP wrapping", Steel Compos. Struct., 30(5), 417-432. http://dx.doi.org/10.12989/scs.2019.30.5.417.
  39. Sedghi, Y., et al. (2018), "Application of ANFIS technique on performance of C and L shaped angle shear connectors", Smart Struct. Syst., 22(3), 335-340. http://dx.doi.org/10.12989/sss.2018.22.3.335
  40. Shah, S., et al. (2015), "Steel rack connections: Identification of most influential factors and a comparison of stiffness design methods", PLoS One, 10(10), e0139422. https://doi.org/10.1371/journal.pone.0139422.
  41. Shah, S., et al. (2016a), "Behavior of industrial steel rack connections", Mech. Syst. Signal Pr., 70-71, 725-740. https://doi.org/10.1016/j.ymssp.2015.08.026.
  42. Shah, S., et al. (2016b), "Behavior of steel pallet rack beam-to-column connections at elevated temperatures", Thin-Wall. Struct., 106, 471-483. https://doi.org/10.1016/j.tws.2016.05.021.
  43. Shahabi, S., et al. (2016a), "Numerical analysis of channel connectors under fire and a comparison of performance with different types of shear connectors subjected to fire", Steel Compos. Struct., 20(3), 651-669. http://dx.doi.org/10.12989/scs.2016.20.3.651.
  44. Shahabi, S., et al. (2016b), "Performance of shear connectors at elevated temperatures-A review", Steel Compos. Struct., 20(1), 185-203. http://dx.doi.org/10.12989/scs.2016.20.1.185.
  45. Sharafi, P., et al. (2018a), "Interlocking system for enhancing the integrity of multi-storey modular buildings", Automat. Constr. 85, 263-272. https://doi.org/10.1016/j.autcon.2017.10.023.
  46. Sharafi, P., et al. (2018b), "Lateral force resisting systems in lightweight steel frames: recent research advances", Thin-Wall. Struct., 130, 231-253. https://doi.org/10.1016/j.tws.2018.04.019.
  47. Sharafi, P., et al. (2018c), "Identification of factors and decision analysis of the level of modularization in building construction", J. Architect. Eng., 24(2), 04018010. https://doi.org/10.1061/(ASCE)AE.1943-5568.0000313.
  48. Shariat, M., et al. (2018), "Computational Lagrangian Multiplier Method by using for optimization and sensitivity analysis of rectangular reinforced concrete beams", Steel Compos. Struct., 29(2), 243-256. http://dx.doi.org/10.12989/scs.2018.29.2.243.
  49. Shariati, A., et al. (2012a), "Investigation of channel shear connectors for composite concrete and steel T-beam", Int. J. Phys. Sci., 7(11), 1828-1831. DOI: 10.5897/IJPS11.1604.
  50. Shariati, M., et al. (2010), "Experimental and analytical study on channel shear connectors in light weight aggregate concrete", Proceedings of the 4th international conference on steel & composite structures.
  51. Shariati, M., et al. (2011a), "Experimental and numerical investigations of channel shear connectors in high strength concrete", Proceedings of the 2011 world congress on advances in structural engineering and mechanics (ASEM'11+).
  52. Shariati, M., et al. (2011b), "Behavior of channel shear connectors in normal and light weight aggregate concrete (experimental and analytical study)", Adv. Materi.Res., 168-170, 2303-2307. https://doi.org/10.4028/www.scientific.net/AMR.168-170.2303.
  53. Shariati, M., et al. (2011c), "Shear resistance of channel shear connectors in plain, reinforced and lightweight concrete", Scientific Res. Essays, 6(4), 977-983. DOI: 10.5897/SRE10.1120.
  54. Shariati, M., et al. (2012b), "Fatigue energy dissipation and failure analysis of channel shear connector embedded in the lightweight aggregate concrete in composite bridge girders", Proceedings of the 5th international conference on engineering failure analysis.
  55. Shariati, M., et al. (2012c), "Experimental assessment of channel shear connectors under monotonic and fully reversed cyclic loading in high strength concrete", Mater. Design, 34, 325-331. https://doi.org/10.1016/j.matdes.2011.08.008.
  56. Shariati, M., et al. (2013), "Comparison of behaviour between channel and angle shear connectors under monotonic and fully reversed cyclic loading", Constr. Build. Mater., 38, 582-593. https://doi.org/10.1016/j.conbuildmat.2012.07.050.
  57. Shariati, M., et al. (2014), "Fatigue energy dissipation and failure analysis of angle shear connectors embedded in high strength concrete", Eng. Fail. Anal., 41, 124-134. https://doi.org/10.1016/j.engfailanal.2014.02.017.
  58. Shariati, M., et al. (2016), "Comparative performance of channel and angle shear connectors in high strength concrete composites: An experimental study", Constr. Build. Mater., 120, 382-392. DOI: 10.1016/j.conbuildmat.2016.05.102.
  59. Shariati, M., et al. (2018), "Experimental investigations on monotonic and cyclic behavior of steel pallet rack connections", Eng. Fail. Anal., 85, 149-166. DOI: 10.1016/j.engfailanal.2017.08.014.
  60. Shariati, M., et al. (2019a), "Application of waste tire rubber aggregate in porous concrete", Smart Struct. Syst., 24(4), 553-566. https://doi.org/10.12989/sss.2019.24.4.553.
  61. Shariati, M., et al. (2019b), "Application of Extreme Learning Machine (ELM) and Genetic Programming (GP) to design steel-concrete composite floor systems at elevated temperatures", Steel Compos. Struct., 33(3), 319-332. https://doi.org/10.12989/scs.2019.33.3.319.
  62. Shariati, M., et al. (2019c). "Experimental investigation on the effect of cementitious materials on fresh and mechanical properties of self-consolidating concrete", Adv. Concrete Constr., 8(3), 225-237. https://doi.org/10.12989/acc.2019.8.3.225.
  63. Shariati, M., et al. (2019d), "Numerical study on the structural performance of corrugated low yield point steel plate shear walls with circular openings", Steel Compos. Struct., 33(4), 569-581.DOI: https://doi.org/10.12989/scs.2019.33.4.569
  64. Shariati, M., et al. (2019e). "Moment-rotation estimation of steel rack connection using extreme learning machine", Steel Compos. Struct., 31(5), 427-435. http://dx.doi.org/10.12989/scs.2019.31.5.427.
  65. Shariati, M. et al. (2019), "Application of a hybrid artificial neural network-particle swarm optimization (ANN-PSO) model in behavior prediction of channel shear connectors embedded in normal and high-strength concrete", Appl. Sciences, 9(24), 55-34. DOI: https://doi.org/10.3390/app9245534.
  66. Shariati, M., et al. (2020), "A novel approach to predict shear strength of tilted angle connectors using artificial intelligence techniques", Engineering with Computers. DOI: 10.1007/s00366-019-00930-x.
  67. Sinaei, H., et al. (2011), "Numerical investigation on exterior reinforced concrete Beam-Column joint strengthened by composite fiber reinforced polymer (CFRP)", Int. J. Phys. Sci., 6(28), 6572-6579. DOI: 10.5897/IJPS11.1225.
  68. Sinaei, H., et al. (2012), "Evaluation of reinforced concrete beam behaviour using finite element analysis by ABAQUS", Sci. Res. Essays, 7(21), 2002-2009. DOI: 10.5897/SRE11.1393.
  69. Suhatril, M., et al. (2019), "Significance of surface eco-protection techniques for cohesive soils slope in selangor, Malaysia", Geotech. Geological Eng., 37(3), 2007-2014. https://doi.org/10.1007/s10706-018-0740-3.
  70. Taheri, E., et al. (2019), "Investigation of a method for strengthening perforated cold-formed steel profiles under compression loads", Appl. Sciences, 9(23), 5085. https://doi.org/10.3390/app9235085.
  71. Tahmasbi, F., et al. (2016), "Shear capacity of C-shaped and L-shaped angle shear connectors", PLoS One, 11(8), e0156989.DOI: 10.1371/journal.pone.0156989.
  72. Tao, Z., et al. (2005), "Experimental behaviour of stiffened concrete-filled thin-walled hollow steel structural (HSS) stub columns", J. Constr. Steel Res., 61(7), 962-983. https://doi.org/10.1016/j.jcsr.2004.12.003.
  73. Toghroli, A., et al. (2014), "Prediction of shear capacity of channel shear connectors using the ANFIS model", Steel Compos. Struct., 17(5), 623-639. http://dx.doi.org/10.12989/scs.2014.17.5.623.
  74. Toghroli, A. (2015), Applications of the ANFIS and LR models in the prediction of shear connection in composite beams/Ali Toghroli, University of Malaya.
  75. Toghroli, A., et al. (2016), "Potential of soft computing approach for evaluating the factors affecting the capacity of steel-concrete composite beam", J. Intel. Manufact., 1-9. https://doi.org/10.1007/s10845-016-1217-y.
  76. Toghroli, A., et al. (2017), "Investigation on composite polymer and silica fume-rubber aggregate pervious concrete", Proceedings of the 5th International Conference on Advances in Civil, Structural and Mechanical Engineering - CSM 2017, Zurich, Switzerland.
  77. Toghroli, A., et al. (2018a), "Evaluation of the parameters affecting the Schmidt rebound hammer reading using ANFIS method", Comput Concret, 21(5), 525-530. http://dx.doi.org/10.12989/cac.2018.11.5.525.
  78. Toghroli, A., et al. (2018b), "A review on pavement porous concrete using recycled waste materials", Smart Struct. Syst., 22(4), 433-440. http://dx.doi.org/10.12989/sss.2018.22.4.433.
  79. Trung, N.T., et al. (2019a), "Reduction of cement consumption by producing smart green concretes with natural zeolites", Smart Struct. Syst., 24(3), 415-425. http://dx.doi.org/10.12989/sss.2019.24.3.415.
  80. Trung, N.T., et al. (2019b), "Moment-rotation prediction of precast beam-to-column connections using extreme learning machine", Struct. Eng. Mech., 70(5), 639-647. https://doi.org/10.12989/sem.2019.70.5.639.
  81. Vali, R., et al. (2019), "A three-dimensional numerical comparison of bearing capacity and settlement of tapered and under-reamed piles", Int. J. Geotech. Eng., 13(3), 236-248. https://doi.org/10.1080/19386362.2017.1336586.
  82. Wei, X., et al. (2018), "Distribution of shear force in perforated shear connectors", Steel Compos. Struct., 27(3), 389-399. http://dx.doi.org/10.12989/scs.2018.27.3.389
  83. Whittle, J. and Ramseyer, C. (2009), "Buckling capacities of axially loaded, cold-formed, built-up C-channels", Thin-Wall. Struct., 47(2), 190-201. https://doi.org/10.1016/j.tws.2008.05.014.
  84. Xie, Q., et al. (2019), "An experimental study on the effect of CFRP on behavior of reinforce concrete beam column connections", Steel Compos. Struct., 30(5), 433-441. http://dx.doi.org/10.12989/scs.2019.30.5.433.
  85. Xu, C., et al. (2019), "Using genetic algorithms method for the paramount design of reinforced concrete structures", Struct. Eng. Mech., 71(5), 503-513. https://doi.org/10.12989/sem.2019.71.5.503.
  86. Yan, L. (2016). "Plain concrete cylinders and beams externally strengthened with natural flax fabric reinforced epoxy composites", Mater. Struct., 49(6), 2083-2095. https://doi.org/10.1617/s11527-015-0635-1.
  87. Yan, L., et al. (2014), "Flax fibre and its composites-A review", Compos. Part B: Eng., 56, 296-317. https://doi.org/10.1016/j.compositesb.2013.08.014.
  88. Yin, P., et al. (2016), "Compressive behavior of concrete confined by CFRP and transverse spiral reinforcement. Part A: experimental study", Mater. Struct., 49(3), 1001-1011. https://doi.org/10.1617/s11527-015-0554-1.
  89. Zandi, Y., et al. (2018), "Computational investigation of the comparative analysis of cylindrical barns subjected to earthquake", Steel Compos. Struct., 28(4), 439-447. http://dx.doi.org/10.12989/scs.2018.28.4.439
  90. Zeghiche, J. (2013), "Further tests on thin steel and composite fabricated stubs", J. Constr. Steel Res., 81, 124-137. https://doi.org/10.1016/j.jcsr.2012.11.006.

Cited by

  1. Elevated temperature resistance of concrete columns with axial loading vol.9, pp.4, 2020, https://doi.org/10.12989/acc.2020.9.4.355
  2. Computational analysis of three dimensional steel frame structures through different stiffening members vol.35, pp.2, 2020, https://doi.org/10.12989/scs.2020.35.2.187
  3. Effect of progressive shear punch of a foundation on a reinforced concrete building behavior vol.35, pp.2, 2020, https://doi.org/10.12989/scs.2020.35.2.279
  4. Influence of porosity and cement grade on concrete mechanical properties vol.10, pp.5, 2020, https://doi.org/10.12989/acc.2020.10.5.393
  5. Knowledge-Based Prediction of Load-Carrying Capacity of RC Flat Slab through Neural Network and FEM vol.2021, 2020, https://doi.org/10.1155/2021/4528945
  6. Optimization algorithms for composite beam as smart active control of structures using genetic algorithms vol.27, pp.6, 2020, https://doi.org/10.12989/sss.2021.27.6.1041
  7. Assessment of microstructure and surface effects on vibrational characteristics of public transportation vol.11, pp.1, 2021, https://doi.org/10.12989/anr.2021.11.1.101
  8. Effect of web hole spacing on axial capacity of back-to-back cold-formed steel channels with edge-stiffened holes vol.40, pp.2, 2020, https://doi.org/10.12989/scs.2021.40.2.287
  9. Smart estimation of automatic approach in enhancing the road safety under AASHTO Standard specification and STM vol.79, pp.3, 2021, https://doi.org/10.12989/sem.2021.79.3.389
  10. Experimental study of reversal of multidrug resistance in human leukemia K562/DOX cells by toad venom vol.11, pp.2, 2020, https://doi.org/10.12989/anr.2021.11.2.219
  11. Application of multi-hybrid metaheuristic algorithm on prediction of split-tensile strength of shear connectors vol.28, pp.2, 2020, https://doi.org/10.12989/sss.2021.28.2.167
  12. Analyzing shear strength of steel-concrete composite beam with angle connectors at elevated temperature using finite element method vol.40, pp.6, 2020, https://doi.org/10.12989/scs.2021.40.6.853
  13. Numerical Investigation of Composite Behavior and Strength of Rectangular Concrete-Filled Cold-Formed Steel Tubular Stub Columns vol.14, pp.20, 2020, https://doi.org/10.3390/ma14206221