Structural Engineering and Mechanics

  • 제72권4호
  • /
  • Pages.409-420
  • /
  • 2019
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Flexural behaviour of steel beams reinforced by carbon fibre reinforced polymer: Experimental and numerical study

  • 투고 : 2019.03.19
  • 심사 : 2019.06.13
  • 발행 : 2019.11.25
⟨ 이전 논문 다음 논문 ⟩

초록

The paper presents the results of an experimental and numerical programme to characterize the behaviour of steel beams reinforcement by composite plates. Important failure mode of such plated beams is the debonding of the composite plates from the steel beam due to high level of stress concentration in the adhesive at the ends of the composite plate. In this new research, an experimental and numerical finite element study is presented to calculate the stresses in the sika carbodur and sika wrap reinforced steel beam under mechanical loading. The main objective of the experimental program was the evaluation of the force transfer mechanism, the increase of the load capacity of the steel beam and the flexural stiffness. It also validated different analytical and numerical models for the analysis of sika carbodur and sika wrap reinforced steel beams. In particular, a finite element model validated with respect to the experimental data and in relation to the analytical approach is presented. Experimental and numerical results from the present analysis are presented in order to show the advantages of the present solution over existing ones and to reconcile debonding stresses with strengthening quality.

키워드

과제정보

연구 과제 주관 기관 : French Ministry of Foreign Affairs and International Development (MAEDI), Ministry of National Education, Higher Education and Research (MENESR), Algerian Ministry of Higher Education and Scientific Research (MESRS)

참고문헌

  1. Abaqus guide Version 6.7 (2007), Computer Software for Interactive Finite Element Analysis, Hibbitt, Karlsson and Sorensen, Inc. Pawtucket, RI, USA.
  2. Abdelhak, Z., Hadji, L., Khelifa, Z., Hassaine daouadji, T., E.A. Adda Bedia (2016), "Analysis of buckling response of functionally graded sandwich plates using a refined shear deformation theory", Wind Struct., 22(3), 291-305. https://doi.org/10.12989/was.2016.22.3.291.
  3. Abdederak, R., Hassaine Daouadji, T., Benferhat, R. and Adim, B. (2018), "Nonlinear analysis of damaged RC beams strengthened with glass fiber reinforced polymer plate under symmetric loads", Earthq. Struct., 15(2), 113-122. https://doi.org/10.12989/eas.2018.15.2.113.
  4. Belkacem, A., Hassaine Daouadji, T. and Abbes, B. (2016a), "Buckling analysis of anti-symmetric cross-ply laminated composite plates under different boundary conditions", Appl. Mech., 52(6), 126-141. https://doi.org/10.1007/s10778-016-0787-x.
  5. Belkacem, A., Hassaine Daouadji, T., Rebahi, A., Tounsi, A. (2016b), "An Efficient and Simple Higher Order of Shear Deformation Theory for Static and Free Vibration of Laminated Composite Plates", Earthq. Struct., 11(1), 63-82. https://doi.org/10.12989/eas.2016.11.1.063.
  6. Belkacem, A. and Hassaine Daouadji, T. (2016c), "Effects of thickness stretching in FGM plates using a quasi-3D higher order shear deformation theory", Adv. Mater. Res., 5(4), 223-244. https://doi.org/10.12989/amr.2016.5.4.223.
  7. Ameur, M., Tounsi, A., Benyoucef, S., Bouiadjra, B.B. and Adda Bedia, E.A. (2008), "Stress analysis of steel beams strengthened with a bonded hygrothermal aged composite plate", J. Mech. Mater. Design, 5(2), 143-156. https://doi.org/10.1007/s10999-008-9090-2.
  8. Ashraful, A. and Al Riyami, R. (2018), "Shear strengthening of reinforced concrete beam using natural fibre reinforced polymer laminates", Construct. Build. Mater., 162, 683-696. https://doi.org/10.1016/j.conbuildmat.2017.12.011.
  9. Attia, A., Bousahla, A.A., Tounsi, A., Mahmoud, S.R. and Alwabli, A.S. (2018), "A refined four variable plate theory for thermoelastic analysis of FGM plates resting on variable elastic foundations", Struct. Eng. Mech., 65(4), 453-464. https://doi.org/10.12989/sem.2018.65.4.453.
  10. Al-Saidy, A.H., Klaiber, F.W. and Wipf, T.J. (2004), "Repair of steel composite beams with carbon fiber-reinforced polymer plates", J. Compos. Construct., 8(2), 163-172. https://doi.org/10.1061/(ASCE)1090-0268(2004)8:2(163).
  11. Benyoucef, S, Tounsi, A, Meftah, S.A. and Adda Bedia, E.A. (2006), "Approximate analysis of the interfacial stress concentrations in FRP-RC hybrid beams", Compos. Interfaces, 13(7), 561-571. https://doi.org/10.1163/156855406778440758.
  12. Benachour, A., Benyoucef, S., Tounsi, A. and Adda Bedia, E.A. (2008), "Interfacial stress analysis of steel beams reinforced with bonded prestressed FRP plate", Eng. Struct., 30, 3305-3315. https://doi.org/10.1016/j.engstruct.2008.05.007.
  13. Benachour, A., Hassaine Daouadji, T., Ait atman, H., Tounsi, A. and Meftah, S.A. (2011), "A four variable refined plate theory for free vibrations of functionally graded plates with arbitrary gradient using", Compos. Part B Eng., 42(6), 1386-1394. https://doi.org/10.1016/j.compositesb.2011.05.032.
  14. Benferhat, R., Hassaine Daouadji, T. and Rabahi, A. (2019), "Effect of distribution shape of the porosity on the interfacial stresses of the FGM beam strengthened with FRP plate", Earthq. Struct., 16(5), 601-609. https://doi.org/10.12989/eas.2019.16.5.601.
  15. Benferhat, R., Rabahi, A., Hassaine Daouadji, T., Abbes, B., Adim, B. and Abbes, F. (2018), "Analytical analysis of the interfacial shear stress in RC beams strengthened with prestressed exponentially-varying properties plate", Adv. Mater. Res., 7(1), 29-44. https://doi.org/10.12989/amr.2018.7.1.029.
  16. Benferhat, R., Hassaine Daouadji, T., Mansour, M. and Hadji, L. (2016), "Effect of porosity on the bending and free vibration response of functionally graded plates resting on Winkler-Pasternak foundations", Earthq. Struct., 10(5), 1429-1449. https://doi.org/10.12989/eas.2016.10.6.1429.
  17. Benhenni, M.A., Hassaine Daouadji, T., Abbes, B., Belkacem, A., Li, Y. and Abbes, F. (2018a), "Dynamic analysis for anti-symmetric cross-ply and angle-ply laminates for simply supported thick hybrid rectangular plates", Adv. Mater. Res., 7(2), 83-103. https://doi.org/10.12989/amr.2018.7.2.119.
  18. Benhenni, M.A., Hassaine Daouadji, T., Abbes, B., Li, Y. and Abbes, F. (2018b), "Analytical and Numerical Results for Free Vibration of Laminated Composites Plates", J. Chem. Molecular Eng., 12(6), 300-304.
  19. Benhenni, M.A., Hassaine Daouadji, T., Abbes, B., Abbes, F., Li, Y. and Adim, B. (2019a), "Numerical analysis for free vibration of hybrid laminated composite plates for different boundary conditions", Struct. Eng. Mech., 70(5), 535-549. https://doi.org/10.12989/sem.2019.70.5.535.
  20. Benhenni, M.A., Belkacem, A., Hassaine Daouadji, T., Boussad Abbes, Abbes, F., Li, Y. and Bouzidene, A. (2019b), "A comparison of closed form and finite element solutions for the free vibration of hybrid cross ply laminated plates", Mech. Compos. Mater., 55(2), 181-194. https://doi.org/10.1007/s11029-019-09803-2.
  21. Bensattalah, T., Zidour, M. and Hassaine Daouadji, T. (2018), "Analytical analysis for the forced vibration of CNT surrounding elastic medium including thermal effect using nonlocal Euler-Bernoulli theory", Adv. Mater. Res., 7(3), 163-174. https://doi.org/10.12989/amr.2018.7.3.163.
  22. Bensattalah, T., Hassaine Daouadji, T., Zidour, M., Tounsi, A. and Adda Bedia, E.A. (2016), "Investigation of thermal and chirality effects on vibration of single walled carbon nanotubes embedded in a polymeric matrix using nonlocal elasticity theories", Mech. Compos. Mater., 52(4), 555-568. https://doi.org/10.1007/s11029-016-9606-z.
  23. Belkacem, A., Hassaine Daouadji, T., Rabahi Abderrezak, Benhenni Mohamed Amine, Zidour Mohamed and Abbes Boussad (2018), "Mechanical buckling analysis of hybrid laminated composite plates under different boundary conditions", Struct. Eng. Mech., 66(6), 761-769. https://doi.org/10.12989/sem.2018.66.6.761.
  24. Belkacem, A., Hassaine Daouadji, T., Benferhat, R. and Hadji, L. (2016a), "An efficient and simple higher order shear deformation theory for bending analysis of composite plates under various boundary conditions", Earthq. Struct., 11(1), 63-82. https://doi.org/10.12989/eas.2016.11.1.063.
  25. Belkacem, A., Hassaine Daouadji, T., Abbes, B. and Rabahi, A. (2016b), "Buckling and free vibration analysis of laminated composite plates using an efficient and simple higher order shear deformation theory", Mech. Industry, 17, 512. https://doi.org/10.1051/meca/2015112.
  26. Belkacem, Adim, Hassaine Daouadji, T. and Rabahi, A. (2016c), "A simple higher order shear deformation theory for mechanical behavior of laminated composite plates", IJAS Adv. Struct. Eng., 8, 103-117. https://doi.org/10.1007/s40091-016-0109-x.
  27. Bellifa, H., Benrahou, K.H., Bousahla, A.A., Tounsi, A. and Mahmoud, S.R. (2017), "A nonlocal zeroth-order shear deformation theory for nonlinear postbuckling of nanobeams", Struct. Eng. Mech., 62(6), 695-702. https://doi.org/10.12989/sem.2017.62.6.695.
  28. Bouhadra, A., Tounsi, A., Bousahla, A.A., Benyoucef, S. and Mahmoud, S.R. (2018), "Improved HSDT accounting for effect of thickness stretching inadvanced composite plates", Struct. Eng. Mech., 66(1), 61-73. https://doi.org/10.12989/sem.2018.66.1.061.
  29. Bouakaz, K., Hassaine Daouadji, T., Meftah, S.A., Ameur, M. and Adda Bedia, E.A. (2014), "A Numerical analysis of steel beams strengthened with composite materials", Mech. Compos. Mater., 50(4), 685-696. https://doi.org/10.1007/s11029-014-9435-x.
  30. Chaded, A., Hassaine Daouadji, T., Rabahi, A., Adim, B., Abbes, B., Benferhat, R. and Fazilay, A. (2018), "A high-order closed-form solution for interfacial stresses in externally sandwich FGM plated RC beams", Adv. Mater. Res., 66(4), 317-328. https://doi.org/10.12989/amr.2017.6.4.317.
  31. El Mahi, K.H. Benrahou, K., Belakhdar, A. Tounsi, and Adda Bedia, E.A. (2014), "Effect of the tapered end of a FRP plate on the interfacial stresses in a strengthened beam used in civil engineering applications", Mech. Compos. Mater., 50(4), 465-474. https://doi.org/10.1007/s11029-014-9433-z.
  32. Hadji L., Ait Amar, M., Abdelhak, Z., Hassaine Daouadji, T. and Adda Bedia, E.A. (2016a), "Static and dynamic behavior of FGM plate using a new first shear deformation plate theory", Struct. Eng. Mech., 57(1), 127-140. https://doi.org/10.12989/sem.2016.57.1.127.
  33. Hadji, L., Hassaine daouadji, T., Meziane, M.A.A., Tlidji, Y. and Adda Bedia, E.A. (2016b), "Analysis of functionally graded beam using a new first-order shear deformation theory", Struct. Eng. Mech., 57(2), 315-325. http://dx.doi.org/10.12989/sem.2016.57.2.315.
  34. Hassaine Daouadji, T., Rabahi, A., Abbes, B. and Adim, B. (2016a), "Theoretical and finite element studies of interfacial stresses in reinforced concrete beams strengthened by externally FRP laminates plate", J. Adhesion Sci. Technol., 30(12), 1253-1280. https://doi.org/10.1080/01694243.2016.1140703.
  35. Hassaine Daouadji, T. and Adim, B. (2016b), "Theoretical analysis of composite beams under uniformly distributed load", Adv. Mater. Res., 5(1), 1-9. http://dx.doi.org/10.12989/amr.2016.5.1.001.
  36. Hassaine Daouadji, T., Adim, B. and Benferhat, R. (2016c), "Bending analysis of an imperfect FGM plates under hygro-thermo-mechanical loading with analytical validation", Adv. Mater. Res., 5(1), 35-53. https://doi.org/10.12989/amr.2016.5.1.035.
  37. Hassaine Daouadji T., Lazreg H., Ait Amar M. and Hadj B. (2016d), "Elastic analysis effect of adhesive layer characteristics in steel beam strengthened with a fiber-reinforced polymer plates", Struct. Eng. Mech., 59(1), 83-100. https://doi.org/10.12989/sem.2016.59.1.083.
  38. Hassaine Daouadji, T., Tounsi, A. and Adda Bedia, E.A. (2012), "Analyse des contraintes d'interface dans les poutres en beton arme renforcees par collage des stratifiees composites", Revue de genie industriel, 8, 3-12.
  39. Hassaine Daouadji, T. (2013), "Analytical analysis of the interfacial stress in damaged reinforced concrete beams strengthened by bonded composite plates", Strength Mater., 45(5), 587-597. https://doi.org/10.1007/s11223-013-9496-4.
  40. Hassaine Daouadji, T. (2017), "Analytical and numerical modeling of interfacial stresses in beams bonded with a thin plate", Adv. Comput. Design, 2(1), 57-69. https://doi.org/10.12989/acd.2017.2.1.057.
  41. Jones, R., Swamy, R.N. and Charif, A. (1988), "Plate separation and anchorage of reinforced concrete beams strengthened by epoxy - bonded steel plates", The Structural Engineer, 66(5/1), 85-94.
  42. Khelifa, Z., Hadji, L., Hassaine Daouadji, T. and Bourada, M. (2018), "Buckling response with stretching effect of carbon nanotube-reinforced composite beams resting on elastic foundation", Struct. Eng. Mech., 67(2), 125-130. https://doi.org/10.12989/sem.2018.67.2.125.
  43. Lazreg, H., Hassaine Daouadji, T., Meziane, M.A and Adda Bedia, E.A. (2016a), "Analyze of the interfacial stress in reinforced concrete beams strengthened with externally bonded CFRP plate", Steel Compos. Struct., 20(2), 413-429. https://doi.org/10.12989/scs.2016.20.2.413.
  44. Lazreg, H., Hassaine Daouadji, T., Adda Bedia, E.A. (2016b), "Dynamic behavior of FGM beam using a new first shear deformation theory", Earthq. Struct., 10(2), 451-461. https://doi.org/10.12989/eas.2016.10.2.451.
  45. Mazari. M., Hadji, L., Hassaine Daouadji, T., Tounsi A and Adda Bedia, E.A. (2015), "A new hyperbolic shear deformation plate theory for static analysis of FGM plate based on neutral surface position", Geomech. Eng., 8(3), 305-321. https://doi.org/10.12989/gae.2015.8.3.305.
  46. Panjehpour, M., Demirboga, R. and Ali, A.A.A. (2016), "Behaviour of repaired high strength concrete cylinders with CFRP sheets", J. Civil Eng. Management, 22(1), 56-64. https://doi.org/10.3846/13923730.2014.897965.
  47. Panjehpour, M., Ali, A.A.A., Voo, Y.L. and Aznieta, F.N. (2014a), "Effective Strength of Strut for CFRP-Strengthened Reinforced Concrete Deep Beams Following ACI 318-11", J. Comput. Concrete, 13(1), 135-165. https://doi.org/10.12989/cac.2014.13.1.135.
  48. Panjehpour, M., Ali, A.A.A. and Aznieta, F.N. (2014b), "Energy absorption of reinforced concrete deep beams strengthened with CFRP sheet", Steel Compos. Struct., 16(5), 481-489. https://doi.org/10.12989/scs.2014.16.5.481.
  49. Panjehpour, M., Ali, A.A.A., Voo, Y.L. and Aznieta, F.N. (2014c), "Strut-and-tie model improvement for CFRP-strengthened reinforced concrete deep beams", Materials de construction, 64(314). https://doi.org/10.1016/j.conbuildmat.2017.04.094.
  50. Panjehpour, M., Farzadnia, N., Anwar, M.P. and Ali, A.A.A. (2011), "FRP sheets contribution in common repair techniques of concrete structures with emphasis on concrete columns", J. Sustainable Construct. Eng. Technol., 2(2).
  51. Rabahi, A., Hassaine Daouadji, T., Benferhat, R. and Adim, B. (2018), "Elastic analysis of interfacial stress concentrations in CFRP-RC hybrid beams: Effect of creep and shrinkage", Adv. Mater. Res., 6(3), 257-278. https://doi.org/10.12989/amr.2017.6.3.257.
  52. Rabahi, A., Benferhat, R., Hassaine Daouadji, T., Abbes, B., Adim, B. and Abbes, F. (2019), "Elastic analysis of interfacial stresses in prestressed PFGM-RC hybrid beams", Adv. Mater. Res., 7(2), 83-103. https://doi.org/10.12989/amr.2018.7.2.83.
  53. Rabahi, A., Hassaine Daouadji, T., Abbes, B. and Adim, B. (2016), "Analytical and numerical solution of the interfacial stress in reinforced-concrete beams reinforced with bonded prestressed composite plate", J. Reinforced Plastics Compos., 35(3) 258-272. https://doi.org/10.1177/0731684415613633.
  54. Rabia, B., Hassaine Daouadji, T. and Mansour, M. (2016a), "Free vibration analysis of FG plates resting on the elastic foundation and based on the neutral surface concept using higher order shear deformation theory", Comptes Rendus Mecanique, 344(9), 631-641. https://doi.org/10.1016/j.crme.2016.03.002.
  55. Rabia, B., Hassaine Daouadji, T., Hadji, L. and Mansour, M. (2016b), "Static analysis of the FGM plate with porosities", Steel Compos. Struct., 21(1), 123-136. https://doi.org/10.12989/scs.2016.21.1.123.
  56. Roberts, T.M. (1989), "Approximate analysis of shear and normal stress concentrations in the adhesive layer of plated RC beams", Struct Engr., 67(12), 229-233.
  57. Sallai, B., Hadji, L., Hassaine Daouadji, T. and Adda Bedia, E.A. (2015), "Analytical solution for bending analysis of functionally graded beam", Steel Compos. Struct., 19(4), 829-841. https://doi.org/10.12989/scs.2015.19.4.829.
  58. Shen, H.S. (2001), "Hygrothermal effects on the postbuckling of shear deformable laminated plates", J. Mech. Sci., 43, 1259-1281. https://doi.org/10.1016/S0020-7403(00)00058-8.
  59. Smith S.T and Teng J.G. (2001) "Interfacial stresses in plated RC beams", Eng. Struct., 23(7), 857-871. https://doi.org/10.1016/S0141-0296(00)00090-0.
  60. Hassaine Daouadji, T., Benyoucef, S., Tounsi, A., Benrahou, K.H. and Adda Bedia, E.A. (2008), "Interfacial Stresses Concentrations in FRP - Damaged RC hybrid Beams", Compos. Interfaces, 15(4), 425-440. https://doi.org/10.1163/156855408784514702.
  61. Hassaine Daouadji, T., Benferhat, R. and Adim, B. (2016a), "A novel higher order shear deformation theory based on the neutral surface concept of FGM plate under transverse load", Adv. Mater. Res., 5(2), 107-120. https://doi.org/10.12989/amr.2016.5.2.107.
  62. Hassaine Daouadji, T., Chedad, A. and Belkacem, A. (2016b), "Interfacial stresses in RC beam bonded with a functionally graded material plate", Struct. Eng. Mech., 60(4), 693-705. https://doi.org/10.12989/sem.2016.60.4.693.
  63. Hassaine Daouadji, T. and Adim, B. (2016c) "An analytical approach for buckling of functionally graded plates", Adv. Mater. Res., 5(3), 141-169. https://doi.org/10.12989/amr.2016.5.3.141.
  64. Hassaine Daouadji, T., Benferhat, R. and Adim, B. (2016d), "Bending analysis of an imperfect advanced composite plates resting on the elastic foundations", Coupl. Syst. Mech., 5(3), 269-285. https://doi.org/10.12989/csm.2016.5.3.269.
  65. Hassaine Daouadji, T. and Adim, B. (2017), "Mechanical behaviour of FGM sandwich plates using a quasi-3Dhigher order shear and normal deformation theory", Struct. Eng. Mech., 61(1), 49-63. https://doi.org/10.12989/sem.2017.61.1.049.
  66. Bensattalah, T., Zidour, M., Daouadji, T.H. and Bouakaz, K. (2019), "Theoretical analysis of chirality and scale effects on critical buckling load of zigzag triple walled carbon nanotubes under axial compression embedded in polymeric matrix", Struct. Eng. Mech., 70(3), 269-277. https://doi.org/10.12989/sem.2019.70.3.269.
  67. Tayeb, B., Bouakkaz, K., Zidour, M. and Hassaine Daouadji, T. (2018a), "Critical buckling loads of carbon nanotube embedded in Kerr's medium", Adv. Nano Res., 6(4), 339-356. https://doi.org/10.12989/anr.2018.6.4.339.
  68. Tayeb, B., Zidour, Meziane, M.A.A., Hassaine Daouadji, T. and Tounsi, A. (2018b), "Critical buckling load of carbon nanotube with non-local Timoshenko beam using the differential transform method", J. Civil Environ. Eng., 12(6).
  69. Tounsi, A. (2006), "Improved theoretical solution for interfacial stresses in concrete beams strengthened with FRP plate", Inter J. Solids Struct., 43, 4154-4174. https://doi.org/10.1016/j.ijsolstr.2005.03.074.
  70. Tounsi, A, Hassaine Daouadji, T., Benyoucef, S. and Adda Bedia, E.A. (2009), "Interfacial stresses in FRP-plated RC beams: Effect of adherend shear deformations", J. Adhesion. Adhesive, 29, 313-351. https://doi.org/10.1016/j.ijadhadh.2008.06.008.
  71. Tounsi, A. and Benyoucef, S. (2007), "Interfacial stresses in externally FRP - plated concrete beams", J. Adhesion Adhesives, 27, 207-215. https://doi.org/10.1016/j.ijadhadh.2006.01.009.
  72. Tlidji, Y., Daouadji, T.H., Hadji, L., Tounsi, A. and Bedia, E.A.A. (2014), "Elasticity solution for bending response of functionally graded sandwich plates under thermo mechanical loading", J. Thermal Stress, 37, 852-869. https://doi.org/10.1080/01495739.2014.912917.
  73. Yuan, C., Chen, W., Pham, T. M. and Hao, H. (2019), "Effect of aggregate size on bond behaviour between basalt fibre reinforced polymer sheets and concrete", Compos. Part B Eng., 158, 459-474. https://doi.org/10.1016/j.compositesb.2018.09.089.
  74. Zidani, M.B., Belakhdar, K., Tounsi, A. and Adda Bedia, E.A. (2015), "Finite element analysis of initially damaged beams repaired with FRP plates", Compos. Struct., 134, 429-439. https://doi.org/10.1016/j.compstruct.2015.07.124.
  75. Zidour, M., Hassaine Daouadji, T., Benrahou, K.H., Tounsi, A. and Adda Bedia, E.A. (2014), "Buckling analysis of chiral single walled carbon nanotubes by the nonlocal Timoshenko beam theory", Mech. Compos. Mater., 50(1), 95-104. https://doi.org/10.1007/s11029-014-9396-0.
  76. Zohra A., Lazreg Hadji, T. Hassaine Daouadji, Adda Bedia (2016), "Thermal buckling response of functionally graded sandwich plates with clamped boundary conditions", Smart Struct. Syst., 18(2), 267-291. https://doi.org/10.12989/sss.2016.18.2.267.

피인용 문헌

  1. Predictions of the maximum plate end stresses of imperfect FRP strengthened RC beams: study and analysis vol.9, pp.4, 2019, https://doi.org/10.12989/amr.2020.9.4.265
  2. Effect of porosity distribution rate for bending analysis of imperfect FGM plates resting on Winkler-Pasternak foundations under various boundary conditions vol.9, pp.6, 2020, https://doi.org/10.12989/csm.2020.9.6.575
  3. Study and analysis of the free vibration for FGM microbeam containing various distribution shape of porosity vol.77, pp.2, 2019, https://doi.org/10.12989/sem.2021.77.2.217
  4. Vibration analysis of porous FGM plate resting on elastic foundations: Effect of the distribution shape of porosity vol.10, pp.1, 2019, https://doi.org/10.12989/csm.2021.10.1.061
  5. Analysis on the buckling of imperfect functionally graded sandwich plates using new modified power-law formulations vol.77, pp.6, 2019, https://doi.org/10.12989/sem.2021.77.6.797
  6. Modeling and analysis of the imperfect FGM-damaged RC hybrid beams vol.6, pp.2, 2019, https://doi.org/10.12989/acd.2021.6.2.117
  7. New solution for damaged porous RC cantilever beams strengthening by composite plate vol.10, pp.3, 2019, https://doi.org/10.12989/amr.2021.10.3.169