Earthquakes and Structures

  • 제17권4호
  • /
  • Pages.337-354
  • /
  • 2019
  • /
  • 2092-7614(pISSN)
  • /
  • 2092-7622(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Experimental investigations and FE simulation of exterior BCJs retrofitted with CFRP fabric

  • Halahla, Abdulsamee M. (Civil Engineering Department, Fahad Bin Sultan University) ;
  • Rahman, Muhammad K. (Center for Engineering Research, Research Institute, King Fahd University of Petroleum & Minerals) ;
  • Al-Gadhib, Ali H. (Civil & Environmental Engineering Department, King Fahd University of Petroleum & Minerals) ;
  • Al-Osta, Mohammed A. (Civil & Environmental Engineering Department, King Fahd University of Petroleum & Minerals) ;
  • Baluch, Mohammed H. (Civil & Environmental Engineering Department, King Fahd University of Petroleum & Minerals)
  • 투고 : 2019.05.18
  • 심사 : 2019.08.30
  • 발행 : 2019.10.25
⟨ 이전 논문 다음 논문 ⟩

초록

This paper presents the results of experimental and numerical studies conducted to investigate the behavior of exterior reinforced concrete beam column joints (BCJ) strengthened by using carbon fiber reinforced polymer (CFRP) sheets. Twelve reinforced concrete beam-column joints (BCJ) were tested in an experimental program by simulating the joints in seismically deficient old buildings. One group of BCJs was designed to fail in flexure at the BCJ interface, and the second group was designed to ensure joint shear failure. One specimen in each set was -retrofitted with CFRP sheet wrapped diagonally around the joint. The specimens were subjected to both monotonic and cyclic loading up to failure. 3D finite element simulation of the BCJs tested in the experimental program was carried out using the software ABAQUS, adopting the damage plasticity model (CDP) for concrete. The experimental results showed that retrofitting of the shear deficient, BCJs by CFRP sheets enhanced the strength and ductility and the failure mode changed from shear failure in the joints to the desired flexural failure in the beam segment. The FE simulation of BCJs showed a good agreement with the experimental results, which indicated that the CDP model could be used to model the problems of the monotonic and cyclic loading of beam-column reinforced concrete joints.

키워드

참고문헌

  1. ACI 352R-02 (2002), Recommendations for Design of Beam-Column Connections in Monolithic Reinforced Concrete Structures, American Concrete Institute.
  2. ACI Committee 440, ACI 440.2R-08 (2008), Guide for the Design and Construction of Externally Bonded FRP Systems, American Concrete Institute.
  3. Ahmed, D., Baluch, M.H., Rahman, M.K. and Ilki, A. (2014), "Finite element modeling of seismic performance of low strength concrete exterior beam-column joints", Seismic Evaluation and Rehabilitation of Structures, Springer, Cham. https://doi.org/10.1007/978-3-319-00458-7_13.
  4. Akguzel, U. and Pampanin, S. (2012), "Assessment and design procedure for the seismic retrofit of reinforced concrete beamcolumn joints using FRP composite materials", J. Compos. Constr., 16(1), 21-34. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000242.
  5. Al-Osta, M.A., Al-Khatib, A.M., Baluch, M.H., Azad, A.K. and Rahman, M.K. (2017), "Performance of hybrid beam-column joint cast with high strength concrete", Earthq. Struct., 12(6), 603-617. https://doi.org/10.12989/eas.2017.12.6.603.
  6. Al-Osta, M.A., Al-Sakkaf, H.A., Sharif, A.M., Ahmad, S. and Baluch, M.H. (2018), "Finite element modeling of corroded RC beams using cohesive surface bonding approach", Comput. Concrete, 22(2), 167-182. https://doi.org/10.12989/cac.2018.22.2.167.
  7. Al-Osta, M.A., Khan, U., Baluch, M.H. and Rahman, M.K. (2018), "Effects of variation of axial load on seismic performance of shear deficient RC exterior BCJs", Int. J. Concr. Struct. Mater., 12(1), 46. https://doi.org/10.1186/s40069-018-0277-0.
  8. Alhaddad, M.S., Siddiqui, N.A., Abadel, A.A., Alsayed, S.H. and Al-Salloum, Y.A. (2012), "Numerical investigations on the seismic behavior of FRP and TRM upgraded RC exterior beamcolumn joints", J. Compos. Constr., 16(3), 308-321. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000265.
  9. Alsayed, S.H., Al-Salloum, Y.A., Almusallam, T.H. and Siddiqui, N.A. (2010), "Seismic response of FRP-upgraded exterior RC beam-column joints", J. Compos. Constr., 14(2), 195-208. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000067.
  10. Antonopoulos, C.P. and Triantafillou, T.C. (2003), "Experimental investigation of FRP-strengthened RC beam-column joints", J. Compos. Constr., 7(1), 39-49. https://doi.org/10.1061/(ASCE)1090-0268(2003)7:1(39).
  11. Bakir, P.G. (2003), "Seismic resistance and mechanical behaviour of exterior beam-column joints with crossed inclined bars", Struct. Eng. Mech., 16(4), 493-517. https://doi.org/10.12989/sem.2003.16.4.493.
  12. Bedirhanoglu, I., Llki, A., Pujol, S. and Kumbasar, N. (2010), "Behavior of deficient joints with plain bars and low-strength concrete", ACI Struct. J., 107(3), 300. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000156.
  13. Bindhu, K.R., Jaya, K.P. and Manicka Selvam, V.K. (2008), "Seismic resistance of exterior beam-column joints with nonconventional confinement reinforcement detailing", Struct. Eng. Mech., 30(6), 733-761. https://doi.org/10.12989/sem.2008.30.6.733.
  14. Birtel, V. and Mark, P. (2006), Parameterised Finite Element Modelling of RC Beam Shear Failure, Ababqus User's Conf.
  15. Bruneau, M., Wilson, J.C. and Tremblay, R. (1996), "Performance of steel bridges during the 1995 Hyogo-ken Nanbu (Kobe, Japan) earthquake", Can. J. Civil Eng., 23(3), 678-713. https://doi.org/10.1139/l96-883.
  16. CAN/CSA-S806-12 (2012), Design and Construction of Building Structures with Fibre-reinforced Polymers, Canadian Standards Association, Ontario, Canada.
  17. Carmo, R.N.F., Costa, H., Gomes, G. and Valenca, J. (2017), "Experimental evaluation of lightweight aggregate concrete beam-column joints with different strengths and reinforcement ratios", Struct. Concrete, 18 (6), 950-961. https://doi.org/10.1002/suco.201600166.
  18. Celik, O.C. and Ellingwood, B.R. (2008), "Modeling beamcolumn joints in fragility assessment of gravity load designed reinforced concrete frames", J. Earthq. Eng., 12(3), 357-381. https://doi.org/10.1080/13632460701457215.
  19. Chalioris, C., Kosmidou, P.M. and Papadopoulos, N. (2018), "Investigation of a new strengthening technique for RC deep beams using carbon FRP ropes as transverse reinforcements", Fiber., 6(3), 52. https://doi.org/10.3390/fib6030052.
  20. Chalioris, C.E. and Bantilas, K.E. (2017), "Shear strength of reinforced concrete beam-column joints with crossed inclined bars", Eng. Struct., 140, 241-255. https://doi.org/10.1016/j.engstruct.2017.02.072.
  21. Chalioris, C.E., Favvata, M.J. and Karayannis, C.G. (2008), "Reinforced concrete beam-column joints with crossed inclined bars under cyclic deformations", Earthq. Eng. Struct. Dyn., 37(6), 881-897. https://doi.org/10.1002/eqe.793.
  22. De Vita, A., Napoli, A. and Realfonzo, R. (2017), "Full scale reinforced concrete beam-column joints strengthened with steel reinforced polymer systems", Front. Mater., 4, 1-17. https://doi.org/10.3389/fmats.2017.00018.
  23. Del Vecchio, C., Di Ludovico, M., Balsamo, A., Prota, A., Manfredi, G. and Dolce, M. (2014), "Experimental investigation of exterior RC beam-column joints retrofitted with FRP systems", J. Compos. Constr., 18(4), 04014002. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000459.
  24. El-Amoury, T. and Ghobarah, A. (2002), "Seismic rehabilitation of beam-column joint using GFRP sheets", Eng. Struct., 24(11), 1397-1407. https://doi.org/10.1016/S0141-0296(02)00081-0.
  25. Ghobarah, A. and El-Amoury, T. (2005), "Seismic rehabilitation of deficient exterior concrete frame joints", J. Compos. Constr., 9(5), 408-416. https://doi.org/10.1061/(ASCE)1090-0268(2005)9:5(408).
  26. Ibrahim, A.M. and Sh Mahmood, M. (2009), "Finite element modeling of reinforced concrete beams strengthened with FRP laminates", Eur. J. Sci. Res., 30(4), 526-541. https://doi.org/10.1016/j.conbuildmat.2011.07.018.
  27. Kalyana Rama, J.S., Chauhan, D.R., Sivakumar, M.V.N., Vasan, A. and Murthy, A.R. (2017), "Fracture properties of concrete using damaged plasticity model-A parametric study", Struct. Eng. Mech., 64(1), 59-69. https://doi.org/10.12989/sem.2017.64.1.059.
  28. Karayannis, C.G. and Chalioris, C.E. (2013), "Shear tests of reinforced concrete beams with continuous rectangular spiral reinforcement", Constr. Build. Mater., 46, 86-97. https://doi.org/10.1016/j.conbuildmat.2013.04.023.
  29. Karayannis, C.G. and Sirkelis, G.M. (2008), "Strengthening and rehabilitation of RC beam-column joints using carbon-FRP jacketing and epoxy resin injection", Earthq. Eng. Struct. Dyn., 37(5), 769-790. https://doi.org/10.1002/eqe.785.
  30. Khan, M.I., Al-Osta, M.A., Ahmad, S. and Rahman, M.K. (2018), "Seismic behavior of beam-column joints strengthened with ultra-high performance fiber reinforced concrete", Compos. Struct., 200, 103-119. https://doi.org/10.1016/j.compstruct.2018.05.080.
  31. Le-Trung, K., Lee, K., Lee, J., Lee, D.H. and Woo, S. (2010), "Experimental study of RC beam-column joints strengthened using CFRP composites", Compos. Part B Eng., 41(1), 76-85. https://doi.org/10.1016/j.compositesb.2009.06.005.
  32. Lee, J. and Fenves, G.L. (1998), "Plastic-damage model for cyclic loading of concrete structures", J. Eng. Mech., 124(8), 892-900. https://doi.org/10.1061/(ASCE)0733-9399(1998)124:8(892).
  33. Li, B. and Kulkarni, S.A. (2010), "Seismic behavior of reinforced concrete exterior wide beam-column joints", J. Struct. Eng., 136(1), 26-36. https://doi.org/10.1061/(ASCE)0733-9445(2010)136:1(26).
  34. Liang, X. and Lu, T. (2018), "Seismic evaluation of engineered cementitious composites beam-column-slab subassemblies with various column-to-beam flexural strength ratios", Struct. Concrete, 19(3), 735-746. https://doi.org/10.1002/suco.201600119.
  35. Lu, X., Urukap, T.H., Li, S. and Lin, F. (2012), "Seismic behavior of interior RC beam-column joints with additional bars under cyclic loading", Earthq. Struct., 3(1), 37-57. https://doi.org/10.12989/eas.2012.3.1.037.
  36. Lubliner, J., Oliver, J., Oller, S. and Onate, E. (1989), "A plasticdamage model for concrete", Int. J. Solid. Struct., 25(3), 299-326. https://doi.org/10.1016/0020-7683(89)90050-4.
  37. McCormac, J.C. and Brown, R.H. (2015), Design of Reinforced Concrete, John Wiley & Sons.
  38. Mobin, J.S., Kazemi, M.T. and Attari, N.K.A. (2016), "Cyclic behaviour of interior reinforced concrete beam-column connection with self-consolidating concrete", Struct. Concrete. 17(4), 618-629. https://doi.org/10.1002/suco.201500133.
  39. Niroomandi, A., Maheri, A., Maheri, M.R. and Mahini, S.S. (2010), "Seismic performance of ordinary RC frames retrofitted at joints by FRP sheets", Eng. Struct., 32(8), 2326-2336. https://doi.org/10.1016/j.engstruct.2010.04.008.
  40. Pampanin, S., Calvi, G.M. and Moratti, M. (2002), "Seismic behavior of RC beam-column joints designed for gravity only", 12th Eur. Conf. Earthq. Eng.
  41. Priestley, M.J.N. (1997), "Displacement-based seismic assessment of reinforced concrete buildings", J. Earthq. Eng., 1(1), 157-192. https://doi.org/10.1080/13632469708962365.
  42. Ravi, R.S. and Arulraj, P.G. (2010), "Experimental investigation on behavior of reinforced concrete beam column joints retrofitted with GFRP-AFRP hybrid wrapping", Int. J. Civil Struct. Eng., 1(2), 245.
  43. Realfonzo, R. and Napoli, A. (2009), "Cyclic behavior of RC columns strengthened by FRP and steel devices", J. Struct. Eng., 135(10), 1164-1176. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000048.
  44. Roth, M.J., Slawson, T.R. and Flores, O.G. (2010), "Flexural and tensile properties of a glass fiber-reinforced ultra-high-strength concrete: an experimental, micromechanical and numerical study", Comput. Concrete, 7(2), 169-190. https://doi.org/10.12989/cac.2010.7.2.169.
  45. Saatcioglu, M., Mitchell, D., Tinawi, R., Gardner, N.J., Gillies, A.G., Ghobarah, A., Anderson, D.L. and Lau, D. (2001), "The August 17, 1999, Kocaeli (Turkey) earthquake-damage to structures", Can. J. Civil Eng., 28(4), 715-737. https://doi.org/10.1139/cjce-28-4-715.
  46. Sasmal, S., Ramanjaneyulu, K., Novak, B., Srinivas, V., Saravana Kumar, K., Korkowski, C., Roehm, C., Lakshmanan, N. and Iyer, N.R. (2011), "Seismic retrofitting of nonductile beamcolumn sub-assemblage using FRP wrapping and steel plate jacketing", Constr. Build. Mater., 25(1), 175-182. https://doi.org/10.1016/j.conbuildmat.2010.06.041.
  47. Sika Construction Chemicals (2006), Sikadur (R) -30 LP, Product Data Sheet.
  48. Supaviriyakit, T., Pimanmas, A. and Warnitchai, P. (2008), "Nonlinear finite element analysis of non-seismically detailed interior reinforced concrete beam-column connection under reversed cyclic load", ScienceAsia, 34, 49-58. https://doi.org/10.2306/scienceasia1513-1874.2008.34.049.
  49. Thirumalaiselvi, A., Anandavalli, N., Rajasankar, J. and Iyer, N.R. (2016), "Numerical evaluation of deformation capacity of laced steel-concrete composite beams under monotonic loading", Steel Compos. Struct., 20(1), 167-184. http://dx.doi.org/10.12989/scs.2016.20.1.167.
  50. Tsonos, A.D.G. (2014), "A new method for earthquake strengthening of old R/C structures without the use of conventional reinforcement", Struct. Eng. Mech., 52(2), 391-403. http://dx.doi.org/10.12989/sem.2014.52.2.391.
  51. Tsonos, A.G. (2004a), "Effectiveness of CFRP-jackets and RCjackets in post-earthquake and pre-earthquake retrofitting of beam-column subassemblages", 13th World Conference on Earthquake Engineering.
  52. Tsonos, A.G. (2004b), "Improvement of the earthquake resistance of R/C beam-column joints under the influence of P-${\Delta}$ effect and axial force variations using inclined bars", Struct. Eng. Mech., 18(4), 389-410. https://doi.org/10.12989/sem.2004.18.4.389.

피인용 문헌

  1. Experimental analysis of shear deficient reinforced concrete beams strengthened by glass fiber strip composites and mechanical stitches vol.40, pp.2, 2019, https://doi.org/10.12989/scs.2021.40.2.267