DOI QR코드

DOI QR Code

Seismic performance of composite plate shear walls with variable column flexural stiffness

  • Curkovic, Ivan (Department of Structures, University of Zagreb, Faculty of Civil Engineering) ;
  • Skejic, Davor (Department of Structures, University of Zagreb, Faculty of Civil Engineering) ;
  • Dzeba, Ivica (Department of Structures, University of Zagreb, Faculty of Civil Engineering) ;
  • De Matteis, Gianfranco (Department of Architecture and Industrial Design, University of Campania Luigi Vanvitelli)
  • 투고 : 2018.11.14
  • 심사 : 2019.03.22
  • 발행 : 2019.10.10

초록

Cyclic behaviour of composite (steel-concrete) plate shear walls (CPSW) with variable column flexural stiffness is experimentally and numerically investigated. The investigation included design, fabrication and testing of three pairs of one-bay one-storey CPSW specimens. The reference specimen pair was designed in way that its column flexural stiffness corresponds to the value required by the design codes, while within the other two specimen pairs column flexural stiffness was reduced by 18% and 36%, respectively. Specimens were subjected to quasi-static cyclic tests. Obtained results indicate that column flexural stiffness reduction in CPSW does not have negative impact on the overall behaviour allowing for satisfactory performance for up to 4% storey drift ratio while also enabling inelastic buckling of the infill steel plate. Additionally, in comparison to similar steel plate shear wall (SPSW) specimens, column "pull-in" deformations are less pronounced within CPSW specimens. Therefore, the results indicate that prescribed minimal column flexural stiffness value used for CPSW might be conservative, and can additionally be reduced when compared to the prescribed value for SPSWs. Furthermore, finite element (FE) pushover simulations were conducted using shell and solid elements. Such FE models can adequately simulate cyclic behaviour of CPSW and as such could be further used for numerical parametric analyses. It is necessary to mention that the implemented pushover FE models were not able to adequately reproduce column "pull-in" deformation and that further development of FE simulations is required where cyclic loading of the shear walls needs to be simulated.

키워드

참고문헌

  1. AISC (2010), ANSI/AISC 341-10: Seismic Provisions for Structural Steel Buildings; American Institute of Steel Construction (AISC), Chicago, IL, USA.
  2. Ali, M.M., Osman, S.A., Husam, O.A. and Al-Zand, A.W. (2018), "Numerical study of the cyclic behavior of steel plate shear wall systems (SPSWs) with differently shaped openings", Steel Compos. Struct., Int. J., 26(3), 361-373. https://doi.org/10.12989/scs.2018.26.3.361
  3. ANSYS (2012), User's Manual (Version 14.5); Swanson Analysis Systems Inc., Houston, TX, USA.
  4. Arabzadeh, A., Soltani, M. and Ayazi, A. (2011), "Experimental investigation of composite shear walls under shear loadings", Thin-Wall. Struct., 49(7), 842-854. https://doi.org/10.1016/j.tws.2011.02.009
  5. Astaneh-Asl, A. (2002), Seismic Behavior and Design of Composite Steel Plate Shear Walls, Steel TIPS Report, Structural Steel Education Council, Moraga, CA, USA.
  6. ATC (1992), ATC-24: Guidelines for Cyclic Seismic Testing of Components of Steel Structures; Applied Technology Council, Redwood City, CA, USA.
  7. Brando, G., D'Agostino, F. and De Matteis, G. (2013), "Experimental tests of a new hysteretic damper made of buckling inhibited shear panels", Mater. Struct./Materiaux et Constructions, 46, 2121-2133. https://doi.org/10.1617/s11527-013-0040-6
  8. Budahazy, V. (2015), "Uniaxial cyclic steel behavior and model for dissipative structures", Ph.D. Dissertation; Budapest University of Technology and Economics, Budapest, Hungary.
  9. CEN (2004), EN 1998-1: Eurocode 8. Design of structures for earthquake resistance - Part 1: General rules, seismic actions and rules for buildings; European Committee for Standardization, Brussels, Belgium.
  10. CEN (2005), EN 1993-1-1: Eurocode 3: Design of steel structures - Part 1-1: General rules and rules for buildings; European Committee for Standardization, Brussels, Belgium.
  11. CEN (2009), EN ISO 6892-1:2009 - Metallic materials - Tensile testing - Part 1: Method of test at room temperature; European Committee for Standardization, Brussels, Belgium.
  12. CEN (2011), EN 12390-3:2009 - Testing hardened concrete - Part 3: Compressive strength of test specimens; European Committee for Standardization, Brussels, Belgium.
  13. CEN (2013), EN 12390-13:2013 - Testing hardened concrete -Part 13: Determination of secant modulus of elasticity in compression; European Committee for Standardization, Brussels, Belgium.
  14. CSA (2009), S16-09 Design of Steel Structures; Canadian Standards Association, Toronto, ON, Canada..
  15. Curkovic, I. (2017), "Behaviour of composite plate shear walls under earthquake", Ph.D. Dissertation; University of Zagreb, Zagreb, Croatia. [In Croatian]
  16. Curkovic, I. and Dzeba, I. (2016), "State of the art review on behaviour and calculation of composite plate shear walls", Tehnicki Vjesnik-Technical Gazette, 23(5) 1523-1532. https://doi.org/10.17559/TV-20141111103014
  17. Curkovic, I., Skejic, D. and Dzeba, I. (2017), "11.24: Impact of column flexural stiffness on behaviour of steel plate shear walls", ce/papers, 1(2-3), 3023-3032. https://doi.org/10.1002/cepa.354
  18. Curkovic, I., Skejic, D. and Dzeba, I. (2019), "Seismic performance of steel plate shear walls with variable column flexural stiffness", Steel Compos. Struct., Int. J., 33(1), 833-850. https://doi.org/10.12989/scs.2019.33.1.833
  19. De Matteis, G., Landolfo, R. and Mazzolani, F.M. (2003), "Seismic response of MR steel frames with low-yield steel shear panels", Eng. Struct., 25(2), 155-168. https://doi.org/10.1016/S0141-0296(02)00124-4
  20. De Matteis, G., Mazzolani, F.M. and Panico, S. (2007), "Pure aluminium shear panels as dissipative devices in moment-resisting steel frames", Earthq. Eng. Struct. Dyn., 36, 841-859. https://doi.org/10.1002/eqe.656
  21. De Matteis, G., Mazzolani, F.M. and Panico, S. (2008), "Experimental tests on pure aluminium shear panels with welded stiffeners", Eng. Struct., 30(6), 1734-1744. https://doi.org/10.1016/j.engstruct.2007.11.015
  22. De Matteis, G., Sarracco, G. and Brando, G. (2016), "Experimental tests and optimization rules for steel perforated shear panels", J. Constr. Steel Res., 12, 41-52. https://doi.org/10.1016/j.jcsr.2016.04.025
  23. Desayi, P. and Krishnan, S. (1964), "Equation for the stress-strain curve of concrete", ACI Journal, 61(3), 345-350.
  24. Driver, R.G., Kulak, G.L., Kennedy, J.L. and Elwi, A.E. (1998), "Cyclic test of four-story steel plate shear wall", ASCE, J. Struct. Eng., 124(2), 112-120. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:2(112)
  25. ECCS (1985), Recommended Testing Procedures for Assessing the Behavior of Structural Elements Under Cyclic Loads; European Convention for Constructional Steelwork, Technical Committee 1, TWG 1.3 - Seismic Design, No. 45, Brussels, Belgium.
  26. Elgaaly, M., Caccese, V. and Du, C. (1993), "Postbuckling behavior of steel plate shear walls under cyclic loads", ASCE, J. Struct. Eng., 119(2), 588-605. https://doi.org/10.1061/(ASCE)0733-9445(1993)119:2(588)
  27. fib (2013), fib Model Code for Concrete Structures 2010; Wilhelm Ernst & Sohn, Berlin, Germany.
  28. Guo, L., Rong, Q., Qu, B. and Liu, J. (2017), "Testing of steel plate shear walls with composite columns and infill plates connected to beams only", Eng. Struct., 136, 165-179. https://doi.org/10.1016/j.engstruct.2017.01.027
  29. Hadzhiyaneva, I. and Belev, B. (2014), "Behaviour of Steel Plate Shear Walls with Buckling-Restrained Web Panels", Proceedings of Second European Conference on Earthquake Engineering and Seisimology, Istanbul, Turkey, August.
  30. Hou, H., Qiu, C., Lv, Z. and Sun, Y. (2013), "Cyclic behavior of steel frames infilled with composite panels: experimental and numerical", Open Civil Eng. J., 7, 196-204. https://doi.org/10.2174/1874149501307010196
  31. ISO (2010), ISO 15630-1:2010 - Steel for the reinforcement and prestressing of concrete - Test methods - Part 1: Reinforcing bars, wire rod and wire; International Organization for Standardization, Geneva, Switzerland.
  32. Jin, S., Ou, J. and Liew, J.Y.R. (2016), "Stability of bucklingrestrained steel plate shear walls with inclined-slots: theoretical analysis and design recommendations", J. Constr. Steel Res., 117, 13-23. https://doi.org/10.1016/j.jcsr.2015.10.002
  33. Kalali, H., Hajsadeghi, M., Zirakian, T. and Alaee, F.J. (2015), "Hysteretic performance of SPSWs with trapezoidally horizontal corrugated web-plates", Steel Compos. Struct., Int. J., 19(2), 277-292. https://doi.org/10.12989/scs.2015.19.2.277
  34. Kuhn, P., Peterson, J.P. and Levin, L.R. (1952), A Summary of Diagonal Tension Part I: Methods and Analysis, Technical Note 2661, National Advisory Committee for Aeronautics, Washington, D.C., USA.
  35. Li, C.H., Tsai, K.C. and Lee, H.C. (2014), "Seismic design and testing of the bottom vertical boundary elements in steel plate shear walls. Part 2: experimental studies", Earthq. Eng. Struct. Dyn., 43, 2155-2177. https://doi.org/10.1002/eqe.2442
  36. Lie, W.-Y., Li, G.-Q. and Jiang, J. (2018), "Experimental study on reinforced concrete frames with two-side connected bucklingrestrained steel plate shear walls", Adv. Struct. Eng., 21(3), 460-473. https://doi.org/10.1177/1369433217719985
  37. Liu, W.-Y., Li, G.-Q. and Jiang, J. (2017), "Mechanical behavior of buckling restrained steel plate shear walls with two-side connections", Eng. Struct., 138, 283-292. https://doi.org/10.1016/j.engstruct.2017.02.010
  38. Lubell, A.S., Prion, H.G.L., Ventura, C.E. and Rezai, M. (2000), "Unstiffened steel plate shear wall performance under cyclic loading", ASCE J. Struct. Eng., 126(4), 453-460. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:4(453)
  39. Machaly, E.B., Safar, S.S. and Amer, M.A. (2014), "umerical investigation on ultimate shear strength of steel plate shear walls", Thin-Wall. Struct., 84, 78-90. https://doi.org/10.1016/j.tws.2014.05.013
  40. Massumi, A., Karimi, N. and Ahmadi, M. (2018), "Effects of openings geometry and relative area on seismic performance of steel shear walls", Steel Compos. Struct., Int. J., 28(5), 617-628. https://doi.org/10.12989/scs.2018.28.5.617
  41. Montgomery, C.J. and Medhekar, M. (2001), "Unstiffened steel plate shear wall performance under cyclic loading", ASCE J. Struct. Eng., 127(8), 973-975. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:8(973)
  42. Qi, Y., Gu, Q., Sun, G. and Zhao, B. (2017), "Shear force demand on headed stud for the design of composite steel plate shear wall", Eng. Struct., 148, 780-792. https://doi.org/10.1016/j.engstruct.2017.07.023
  43. Qu, B. and Bruneau, M. (2010), "Behaviour of vertical boundary elements in steel plate shear walls", Eng. J., 47, 109-122.
  44. Park, H.G., Kwack, J.H., Jeon, S.W., Kim, W.K. and Choi, I.R. (2007), "Framed steel plate wall behavior under cyclic lateral loading", ASCE J. Struct. Eng., 133(3), 378-388. https://doi.org/10.1061/(ASCE)0733-9445(2007)133:3(378)
  45. Purba, R. and Bruneau, M. (2014), Seismic Performance of Steel Plate Shear Walls Considering Various Design Approaches. Technical Report MCEER-14-0005, Multidisciplinary Center for Earthquake Engineering Research, University at Buffalo, State University of New York, Buffalo, NY, USA.
  46. Rahmzadeh, A., Ghassemieh, M., Park, Y. and Abolmaali, A. (2016), "Effect of stiffeners on steel plate shear wall systems", Steel Compos. Struct., Int. J., 20(3), 545-569. https://doi.org/10.12989/scs.2016.20.3.545
  47. Rahnavard, R., Hassanipour, A. and Mounesi, A. (2016), "Numerical study on important parameters of composite steelconcrete shear walls", J. Constr. Steel Res., 121, 441-456. https://doi.org/10.1016/j.jcsr.2016.03.017
  48. Rassouli, B., Shafaei, S., Ayazi, A. and Farahbod, F. (2016), "Experimental and numerical study on steel-concrete composite shear wall using light-weight concrete", J. Constr. Steel Res., 126, 117-128. https://doi.org/10.1016/j.jcsr.2016.07.016
  49. Sabelli, R. and Bruneau, M. (2007), Steel Design Guide 20 - Steel Plate Shear Walls, American Institute of Steel Construction (AISC), USA.
  50. Shafaei, S., Ayazi, A. and Farahbond, F. (2016), "The effect of concrete panel thickness upon composite steel plate shear walls", J. Constr. Steel Res., 117, 81-90. https://doi.org/10.1016/j.jcsr.2015.10.006
  51. Shafaei, S., Farahbod, F. and Ayazi, A. (2017), "Concrete stiffened steel plate shear walls with an unstiffened opening", Structures, 12, 40-53. https://doi.org/10.1016/j.istruc.2017.07.004
  52. Thorburn, G.L., Kulak, L.J. and Montgomery, C.J. (1983), Analysis of Steel Plate Shear Walls, Structural Engineering Report No. 107; University of Alberta, Edmonton, Alberta, Canada..
  53. Vian, D. (2005), "Steel plate shear walls for seismic design and retrofit of building structures", Ph.D. Dissertation; University of New York at Buffalo, Buffalo, NY, USA.
  54. Wagner, H. (1931), Flat Sheet Metal Girders with Very Thin Webs, Part III: Sheet Metal Girders with Spars Resistant to Bending -The Stress in Uprights - Diagonal Tension Fields, Technical Memorandum No. 606, National Advisory Committee for Aeronautics, Washington, D.C., USA.
  55. Wei, M.W., Liew, J.Y.R., Du, Y. and Fu, X.-Y. (2013), "Seismic behavior of novel partially connected buckling-restrained steel plate shear walls", Soil Dyn. Earthq. Eng., 103, 64-75. https://doi.org/10.1016/j.soildyn.2017.09.021
  56. Wei, M.-W., Liew, J.Y.R. and Fu, X.-Y. (2017), "Shear resistance of buckling-restrained steel plate shear walls", Int. J. Steel Struct., 17(3), 1233-1248. https://doi.org/10.1007/s13296-017-9029-2
  57. Willam, K.J. and Warnke, E.D. (1975), "Constitutive Model for the Triaxial Behavior of Concrete", Proceedings, International Association for Bridge and Structural Engineering, Vol. 19, ISMES, Bergamo, Italy.
  58. Zhao, Q. (2006), "Experimental and Analytical Studies of Cyclic Behavior of Steel and Composite Shear Wall Systems", Ph.D. Dissertation, University of California, Berkeley, CA, USA.
  59. Zhao, Q. and Astaneh-Asl, A. (2004), "Cyclic behavior of traditional and innovative composite shear walls", J. Struct. Eng., 130(2), 271-284. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:2(271)
  60. Zhao, Q. and Astaneh-Asl, A. (2007), "Seismic behavior of composite shear wall systems and application of smart structures technology", Int. J. Steel Struct., 7(1), 69-75.

피인용 문헌

  1. Behavior of L-shaped double-skin composite walls under compression and biaxial bending vol.37, pp.4, 2020, https://doi.org/10.12989/scs.2020.37.4.405