DOI QR코드

DOI QR Code

Seismic performance of steel plate shear walls with variable column flexural stiffness

  • Curkovic, Ivan (Department of Structures, University of Zagreb, Faculty of Civil Engineering) ;
  • Skejic, Davor (Department of Structures, University of Zagreb, Faculty of Civil Engineering) ;
  • Dzeba, Ivica (Department of Structures, University of Zagreb, Faculty of Civil Engineering)
  • 투고 : 2018.11.14
  • 심사 : 2019.09.26
  • 발행 : 2019.10.10

초록

In the present study, the behavior of steel plate shear walls (SPSW) with variable column flexural stiffness is experimentally and numerically investigated. Altogether six one-bay one-story specimens, three moment resisting frames (MRFs) and three SPSWs, were designed, fabricated and tested. Column flexural stiffness of the first specimen pair (one MRF and one SPSW) corresponded to the value required by the design codes, while for the second and third pair it was reduced by 18% and 36%, respectively. The quasi-static cyclic test result indicate that SPSW with reduced column flexural stiffness have satisfactory performance up to 4% story drift ratio, allow development of the tension field over the entire infill panel, and cause negligible column "pull-in" deformation which indicates that prescribed minimal column flexural stiffness value, according to AISC 341-10, might be conservative. In addition, finite element (FE) pushover simulations using shell elements were developed. Such FE models can predict SPSW cyclic behavior reasonably well and can be used to conduct numerical parametric analyses. It should be mentioned that these FE models were not able to reproduce column "pull-in" deformation indicating the need for further development of FE simulations with cyclic load introduction which will be part of another paper.

키워드

참고문헌

  1. AISC (2010), ANSI/AISC 341-10: Seismic Provisions for Structural Steel Buildings; American Institute of Steel Construction (AISC), Chicago, IL, USA.
  2. ANSYS (2012), User's Manual (Version 14.5); Swanson Analysis Systems Inc., Houston, TX, USA.
  3. Astaneh-Asl, A. (2001), "Seismic Behavior and Design of Steel Shear Walls", Steel TIPS Report; Structural Steel Education Council, Moraga, CA, USA.
  4. ATC (1992), ATC-24: Guidelines for Cyclic Seismic Testing of Components of Steel Structures; Applied Technology Council, Redwood City, CA, USA.
  5. ATC (2010), PEER/ATC-72-1: Modelling and Acceptance Criteria for Seismic Design and Analysis of Tall Buildings; Applied Technology Council, Redwood City, CA, USA.
  6. Basler, K. (1961), "Strength of Plate Girders in Shear, Proc. ASCE, 87, (ST7), (October 1961), Reprint No. 186 (61-13)", Fritz Laboratory Reports; Paper 70.
  7. Berman, J.W. and Bruneau, M. (2003), "Plastic analysis and design of steel plate shear walls", J. Struct. Eng., 126(11), 1448-1456. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:11(1448)
  8. Budahazy, V. (2015), "Uniaxial cyclic steel behavior and model for dissipative structures", Ph.D. Dissertation; Budapest University of Technology and Economics, Budapest, Hungary.
  9. CEN (2004), EN 1998-1: Eurocode 8. Design of structures for earthquake resistance - Part 1: General rules, seismic actions and rules for buildings; European Committee for Standardization, Brussels, Belgium.
  10. CEN (2005), EN 1993-1-1: Eurocode 3: Design of steel structures - Part 1-1: General rules and rules for buildings; European Committee for Standardization, Brussels, Belgium.
  11. CEN (2009), EN ISO 6892-1:2009 - Metallic materials - Tensile testing - Part 1: Method of test at room temperature; European Committee for Standardization, Brussels, Belgium.
  12. CSA (2009), S16-09 Design of Steel Structures; Canadian Standards Association, Toronto, ON, Canada..
  13. Curkovic, I. (2017), "Behaviour of composite plate shear walls under earthquake", Ph.D. Dissertation; University of Zagreb, Zagreb, [in Croatian].
  14. Curkovic, I. and Dzeba, I. (2016), "State of the art review on behaviour and calculation of composite plate shear walls", Tehnicki Vjesnik-Technical Gazette, 23(5) 1523-1532. https://doi.org/10.17559/TV-20141111103014
  15. Curkovic, I., Skejic, D. and Dzeba, I. (2017), "11.24: Impact of column flexural stiffness on behaviour of steel plate shear walls", ce/papers, 1(2-3), 3023-3032. https://doi.org/10.1002/cepa.354
  16. Driver, R.G., Kulak, G.L., Kennedy, J.L. and Elwi, A.E. (1998), "Cyclic test of four-story steel plate shear wall", J. Struct. Eng., 124(2), 112-120. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:2(112)
  17. ECCS (1985), Recommended Testing Procedures for Assessing the Behavior of Structural Elements Under Cyclic Loads; European Convention for Constructional Steelwork, Technical Committee 1, TWG 1.3 - Seismic Design, No. 45, Brussels, Belgium.
  18. Elgaaly, M., Caccese, V. and Du, C. (1993), "Postbuckling behavior of steel plate shear walls under cyclic loads", J. Struct. Eng., 119(2), 588-605. https://doi.org/10.1061/(ASCE)0733-9445(1993)119:2(588)
  19. FEMA (2009), FEMA P-750: NEHRP Recommended Seismic Provisions for New Buildings and Other Structures; Building Seismic Safety Council, Washington, D.C., USA.
  20. Kalali, H., Hajsadeghi, M., Zirakian, T. and Alaee, F.J. (2015), "Hysteretic performance of SPSWs with trapezoidally horizontal corrugated web-plates", Steel Compos. Struct., Int. J., 19(2), 277-292. https://doi.org/10.12989/scs.2015.19.2.277
  21. Krolo, P., Grandic, D. and Smolcic, Z. (2016), "Experimental and numerical study of mild steel behaviour under cyclic loading with variable strain ranges", Adv. Mater. Sci. Eng. http://dx.doi.org/10.1155/2016/7863010
  22. Kuhn, P., Peterson, J.P. and Levin, L.R. (1952), A Summary of Diagonal Tension Part I: Methods and Analysis, Technical Note 2661; National Advisory Committee for Aeronautics, Washington, D.C., USA.
  23. Lubell, A.S., Prion, H.G.L., Ventura, C.E. and Rezai, M. (2000), "Unstiffened steel plate shear wall performance under cyclic loading", J. Struct. Eng., 126(4), 453-460. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:4(453)
  24. Machaly, E.B., Safar, S.S. and Amer, M.A. (2014), "Numerical investigation on ultimate shear strength of steel plate shear walls", Thin-Wall. Struct., 84, 78-90. https://doi.org/10.1016/j.tws.2014.05.013
  25. Montgomery, C.J. and Medhekar, M. (2001), "Unstiffened steel plate shear wall performance under cyclic loading", J. Struct. Eng., 127(8), 973-975. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:8(973)
  26. Park, H.G., Kwack, J.H., Jeon, S.W., Kim, W.K. and Choi, I.R. (2007), "Framed steel plate wall behavior under cyclic lateral loading", J. Struct. Eng., 133(3), 378-388. https://doi.org/10.1061/(ASCE)0733-9445(2007)133:3(378)
  27. Purba, R. and Bruneau, M. (2010), Impact of Horizontal Boundary Elements Design on Seismic Behavior of Steel Plate Shear Walls, Technical Report MCEER-10-0007; Multidisciplinary Center for Earthquake Engineering Research, University of New York at Buffalo, Buffalo, NY, USA.
  28. Purba, R. and Bruneau, M. (2014), Seismic Performance of Steel Plate Shear Walls Considering Various Design Approaches. Technical Report MCEER-14-0005; Multidisciplinary Center for Earthquake Engineering Research, University at Buffalo, State University of New York, Buffalo, NY, USA.
  29. Qu, B. and Bruneau, M. (2010), "Behaviour of vertical boundary elements in steel plate shear walls", Eng. J., 47, 109-122.
  30. Qin, Y., Lu, J., Huang, L.C.X. and Cao, S. (2017a), "Flexural behavior of beams in steel plate shear walls", Steel Compos. Struct., Int. J., 23(4), 473-481. https://doi.org/10.12989/scs.2017.23.4.473
  31. Qin, Y., Lu, J.Y., Huang, L.C.X. and Cao, S. (2017b), "Flexural ehavior of anchor horizontal boundary element in steel plate shear wall", Int. J. Steel Struct., 17(3), 1073-1086. https://doi.org/10.1007/s13296-017-9017-6
  32. Rahmzadeh, A., Ghassemieh, M., Park, Y. and Abolmaali, A. (2016), "Effect of stiffeners on steel plate shear wall systems", Steel Compos. Struct., Int. J., 20(3), 545-569. https://doi.org/10.12989/scs.2016.20.3.545
  33. Sabelli, R. and Bruneau, M. (2007), Steel Design Guide 20 - Steel Plate Shear Walls; American Institute of Steel Construction (AISC), USA.
  34. Sabouri-Ghomi, S. and Sajjadi, S.R.A. (2012), "Experimental and theoretical studies of steel shear walls with and without stiffeners", J. Constr. Steel Res., 75, 152-159. https://doi.org/10.1016/j.jcsr.2012.03.018
  35. Thorburn, G.L., Kulak, L.J. and Montgomery, C.J. (1983), Analysis of Steel Plate Shear Walls, Structural Engineering Report No. 107; University of Alberta, Edmonton, Alberta, Canada..
  36. Timoshenko, S. and Young, D.H. (1968), Elements of Strength of Materials, (5th Edition), Van Nostrand, Princeton, NJ, USA.
  37. Tsai, K.C., Li, C.H. and Lee, H.C. (2014), "Seismic design and testing of the bottom vertical boundary elements in steel plate shear walls. Part 1: design methodology", Earthq. Eng. Struct. Dyn., 43, 2237-2259. https://doi.org/10.1002/eqe.2443
  38. Vian, D. (2005), "Steel plate shear walls for seismic design and retrofit of building structures", Ph.D. Dissertation; University of New York at Buffalo, Buffalo, NY, USA.
  39. Wagner, H. (1931), Flat Sheet Metal Girders with Very Thin Webs, Part III: Sheet Metal Girders with Spars Resistant to Bending -The Stress in Uprights - Diagonal Tension Fields, Technical Memorandum No. 606; National Advisory Committee for Aeronautics, Washington, D.C., USA.