Structural Engineering and Mechanics

  • 제72권1호
  • /
  • Pages.43-60
  • /
  • 2019
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Finite element analysis and axial bearing capacity of steel reinforced recycled concrete filled square steel tube columns

  • Dong, Jing (School of Civil Engineering and Architecture, Xi'an University of Technology) ;
  • Ma, Hui (School of Civil Engineering and Architecture, Xi'an University of Technology) ;
  • Zou, Changming (School of Civil Engineering and Architecture, Xi'an University of Technology) ;
  • Liu, Yunhe (School of Civil Engineering and Architecture, Xi'an University of Technology) ;
  • Huang, Chen (School of Civil Engineering and Architecture, Xi'an University of Technology)
  • 투고 : 2019.03.08
  • 심사 : 2019.05.07
  • 발행 : 2019.10.10
⟨ 이전 논문 다음 논문 ⟩

초록

This paper presents a finite element model which can simulate the axial compression behavior of steel reinforced recycled concrete (SRRC) filled square steel tube columns using the ABAQUS software. The analytical model was established by selecting the reasonable nonlinear analysis theory and the constitutive relationship of material in the columns. The nonlinear analysis of failure modes, deformation characteristics, stress nephogram, and load-strain curves of columns under axial loads was performed in detail. Meanwhile, the influences of recycled coarse aggregate (RCA) replacement percentage, profile steel ratio, width thickness ratio of square steel tube, RAC strength and slenderness ratio on the axial compression behavior of columns were also analyzed carefully. It shows that the results of finite element analysis are in good agreement with the experimental results, which verifies the validity of the analytical model. The axial bearing capacity of columns decreased with the increase of RCA replacement percentage. While the increase of wall thickness of square steel tube, profile steel ratio and RAC strength were all beneficial to improve the bearing capacity of columns. Additionally, the parameter analysis of finite element analysis on the columns was also carried out by using the above numerical model. In general, the SRRC filled square steel tube columns have high bearing capacity and good deformation ability. On the basis of the above analysis, a modified formula based on the American ANSI/AISC 360-10 was proposed to calculate the nominal axial bearing capacity of the columns under axial loads. The research conclusions can provide some references for the engineering application of this kind of columns.

키워드

과제정보

연구 과제 주관 기관 : National Natural Science Foundation of China, Xi'an University of Technology

참고문헌

  1. Akgoz, B. and Civalek, O. (2012), "Analysis of micro-sized beams for various boundary conditions based on the strain gradient elasticity theory", Arch. Appl. Mech., 82(3), 423-443. https://doi.org/10.1007/s00419-011-0565-5.
  2. Akgoz, B. and Civalek, O. (2013), "Buckling analysis of functionally graded microbeams based on the strain gradient theory", Acta Mech. Sin., 224(9), 2185-2201. https://doi.org/10.1007/s00707-013-0883-5.
  3. Akgoz, B. and Civalek, O. (2013), "Buckling analysis of linearly tapered micro-columns based on strain gradient elasticity", Struct. Eng. Mech., 48(2), 195-205. https://doi.org/10.12989/sem.2013.48.2.195.
  4. Akgoz, B. and Civalek, O. (2014), "A new trigonometric beam model for buckling of strain gradient microbeams", Int. J. Mech. Sci., 81, 88-94. https://doi.org/10.1016/j.ijmecsci.2014.02.013.
  5. Akgoz, B. and Civalek, O. (2016), "Bending analysis of embedded carbon nanotubes resting on an elastic foundation using strain gradient theory", Acta Astronaut., 119, 1-12. https://doi.org/10.1016/j.actaastro.2015.10.021.
  6. ANSI/AISC 360-10. (2010), "Specification for structural steel buildings", American Institute of Steel Construction, Chicago, USA.
  7. Balaty, P. and Gjelsyilk, A. (1990), "Coefficient of riction for steel on concrete at high normal stress", J. Mater. Civ. Eng., 2(1), 46-49. https://doi.org/10.1061/(ASCE)0899-1561(1990)2:1(46).
  8. Bing, L., Qi, Z. and Shuang, M. (2014), "Finite element analysis of bearing capacity for recycle concrete filled square steel tubular stub columns under axial compression", J. Arch. Civil Eng., 31(4), 29-34.
  9. Cai, J., Pan, J. and Wu, Y. (2015), "Mechanical behavior of steelreinforced concrete-filled steel tubular (SRCFST) columns under uniaxial compressive loading", Thin-Walled Struct., 97(5), 1-10. https://doi.org/10.1016/j.tws.2015.08.028.
  10. Cardoso, R., Silva, R. V., de Brito, J. and Dhir, R. (2016), "Use of recycled aggregates from construction and demolition waste in geotechnical applications: A literature review", Waste Manage., 34(49), 131-145. https://doi.org/10.1016/j.wasman.2015.12.021.
  11. Chen, H.J., Yen, T. and Chen, K.H. (2003), "Use of building rubbles as recycled aggregates", Cem. Concr. Res., 17(33), 125-132. https://doi.org/10.1016/S0008-8846(02)00938-9.
  12. Chen, Z., Jinjun, X., and Ying, L. (2014), "Bond behaviors of shape steel embedded in recycled aggregate concrete and recycled aggregate concrete filled in steel tubes", Steel Compos. Struct., 17(6), 929-949. http://dx.doi.org/10.12989/scs.2014.17.6.929.
  13. Djebien, R., Hebhoub, H., Belachia, M., Berdoudi, S. and Kherraf, L. (2018), "Incorporation of marble waste as sand in formulation of self-compacting concrete", Struct. Eng. Mech., 67(1), 87-91. https://doi.org/10.12989/sem.2018.67.1.087.
  14. Goksu, C., Saribas, I., Binbir, E., Akkaya, Y. and Ilki, A. (2019), "Structural performance of recycled aggregates concrete sourced from low strength concrete", Struct. Eng. Mech., 69(1), 77-93. https://doi.org/10.12989/sem.2019.69.1.077.
  15. Han, L. H., Liu, W. and Yang, Y.F. (2008), "Behaviour of concretefilled steel tubular stub columns subjected to axially local compression", J. Constr. Steel. Res., 64(4), 377-387. https://doi.org/10.1016/j.jcsr.2007.10.002.
  16. Hawileh, R.A., Abed, F., Abu-Obeidah, A.S. and Abdalla, J.A. (2012), "Experimental investigation of inelastic buckling of built-up steel columns", Steel Compos. Struct., 13(3), 295-308. https://doi.org/10.12989/scs.2012.13.3.295.
  17. Huang, H. (2015), "Experimental research on mechanical behavior of recycled concrete-filled square steel tubular stub columns subjected to axial compression", J. Build. Struct., 36(33),215-221.
  18. Jin, R. and Chen, Q. (2015), "Investigation of concrete Recycling in the U.S. construction Industry", Procedia Eng., 42 (118), 894-901. https://doi.org/10.1016/j.proeng.2015.08.528
  19. Lai, Y.Y., Yeh, L.H., Chen, P.F., Sung, P.H. and Lee, Y.M. (2016), "Management and Recycling of Construction Waste in Taiwan", Procedia Environ. Sci., 69(35), 723-730. https://doi.org/10.1016/j.proenv.2016.07.077.
  20. Li, G. Q., Wang, P. and Hou, H. (2009), "Post-buckling behaviours of axially restrained steel columns in fire", Steel Compos. Struct., 9(2), 89-101. https://doi.org/10.12989/scs.2009.9.2.089.
  21. Ma, H., Xue, J., Liu, Y. and Dong, J. (2016), "Numerical analysis and horizontal bearing capacity of steel reinforced recycled concrete columns", Steel Compos. Struct., 22(4), 797-820. https://doi.org/10.12989/scs.2016.22.4.797.
  22. Ma, H., Xue, J., Liu, Y. and Zhang, X. (2015), "Cyclic loading tests and shear strength of steel reinforced recycled concrete short columns", Eng. Struct., 92(6), 55-68. https://doi.org/10.1016/j.engstruct.2015.03.009.
  23. Ma, H., Xue, J., Zhang, X., and Luo, D. (2013), "Seismic performance of steel-reinforced recycled concrete columns under low cyclic loads", Constr. Build. Mater., 48(11), 229-237. https://doi.org/10.1016/j.conbuildmat.2013.06.019.
  24. Mandal, S. and Gupta, A. (2002), "Strength and durability of recycled aggregate concrete", Australia, Labse Symposium Melbourne.
  25. Mercan, K. and Civalek, O. (2017), "Buckling analysis of Silicon carbide nanotubes (SiCNTs) with surface effect and nonlocal elasticity using the method of HDQ", Compos. Pt. B-Eng., 114, 34-45. https://doi.org/10.1016/j.compositesb.2017.01.067.
  26. Montero, J. and Laserna, S. (2017), "Influence of effective mixing water in recycled concrete", Constr. Build. Mater., 22(132), 343-352. https://doi.org/10.1016/j.conbuildmat.2016.12.006.
  27. Muthuraj, H., Sekar, S.K., Mahendran, M., and Deepak, O.P. (2017), "Post buckling mechanics and strength of cold-formed steel columns exhibiting Local-Distortional interaction mode failure", Struct. Eng. Mech., 64(5), 621-640. https://doi.org/10.12989/sem.2017.64.5.621.
  28. Papayianni, P. (2003), "Recycled aggregate concrete under cyclic loading", Proceedings of the International Symposium on Role of Concrete in Sustainable Development. University of Dundee, Scotland, 509-518.
  29. Poon, C.S., Kou, S.C. and Lam, L. (2002), "Use of recycled aggregates in molded concrete bricks and blocks", Constr. Build. Mater., 16(5), 281-289. https://doi.org/10.1016/S0950-0618(02)00019-3.
  30. Qi, L., Xue, J., Zhai, L., Zhao, X. and Leon, R.T. (2018), "Experimental and numerical studies on seismic performance of traditional style steel-concrete composite frame", Compos. Struct., 201(10), 514-527. https://doi.org/10.1016/j.compstruct.2018.06.049.
  31. Rosado, L.P., Vitale, P., Penteado, C.S.G. and Arena, U. (2017), "Life cycle assessment of natural and mixed recycled aggregate production in Brazil". J. Clean Prod., 12(151), 634-642. https://doi.org/10.1016/j.jclepro.2017.03.068.
  32. Senaratne, S., Lambronsis, G., Mirza, O., Tam, V.W.Y., Long, W.H. (2017), "Recycle concrete in structural Applications for sustainable construction Practices in Australia", Procedia Eng., 23(180), 751-758.
  33. Shah, A., Jan, I.U., Khan, R.U. and Qazi, E.U. (2013), "Experimental investigation on the use of recycled aggregates in producing concrete", Struct. Eng. Mech., 47(4), 545-557. http://dx.doi.org/10.12989/sem.2013.47.4.545.
  34. Shi, G., Liu, Z., Ban, H.Y., Zhang, Y., Shi, Y.J. and Wang, Y.Q. (2012), "Tests and finite element analysis on the local buckling of 420 MPa steel equal angle columns under axial compression", Steel Compos. Struct., 12(1), 31-51. https://doi.org/10.12989/scs.2011.12.1.031.
  35. Tang, Y. C., Li, L. J., Feng, W. X., Liu, F. and Zhu, M. (2018), "Study of seismic behavior of recycled aggregate concrete-filled steel tubular columns", J. Constr. Steel. Res., 148(9), 1-15. https://doi.org/10.1016/j.jcsr.2018.04.031.
  36. Thomas, C., Setien, J., Polanco, J., Alaejos, P. and De Juan, M.S (2013), "Durability of recycled aggregate concrete", Constr. Build. Mater., 40(3), 1054-1065. https://doi.org/10.1016/j.conbuildmat.2012.11.106.
  37. Xiao, J., Huang, Y., Yang, J. and Zhang, C. (2011), "Mechanical properties of confined recycled aggregate concrete under axial compression", Constr. Build. Mater., 26(1), 591-603. https://doi.org/10.1016/j.conbuildmat.2011.06.062.
  38. Xiao, J., Li, W., Fan, Y. and Huang, X. (2012), "An overview of study on recycled aggregate concrete in China (1996-2011)", Constr. Build. Mater., 31(6), 364-383. https://doi.org/10.1016/j.conbuildmat.2011.12.074.
  39. Xu, J. J., Chen, Z. P., Xue, J. Y., Chen, Y. L. and Zhang, J.T. (2017), "Simulation of seismic behavior of square recycled aggregate concrete-filled steel tubular columns", Constr. Build. Mater., 149(9), 553-566. https://doi.org/10.1016/j.conbuildmat.2017.05.013.
  40. Yang, Y. (2015), "Modeling of recycled aggregate concrete-filled steel tube (RACFST) beam-columns subjected to cyclic loading", Steel Compos. Struct., 18(1), 213-233. https://doi.org/10.12989/scs.2015.18.1.213.
  41. Yoda, K. and Shintani, A. (2014), "Building application of recycled aggregate concrete for upper-ground structural elements", Constr. Build. Mater., 30(67), 379-385. https://doi.org/10.1016/j.conbuildmat.2013.12.096.
  42. Young, B. (2005), "Local buckling and shift of effective centroid of cold-formed steel columns", Steel Compos. Struct., 5(2), 235-246. https://doi.org/10.12989/scs.2005.5.2_3.235.
  43. Zhang, K. and Xiao, J. (2018), "Prediction model of carbonation depth for recycled aggregate concrete", Cem. Concr. Compos., 4(88), 86-99. https://doi.org/10.1016/j.cemconcomp.2018.01.013.
  44. Zhou, C. and Chen, Z. (2017), "Mechanical properties of recycled concrete made with different types of coarse aggregate", Constr. Build. Mater., 56(134), 497-506. https://doi.org/10.1016/j.conbuildmat.2016.12.163.

피인용 문헌

  1. Mechanical properties and bearing capacity of CFRP confined steel reinforced recycled concrete columns under axial compression loading vol.79, pp.4, 2019, https://doi.org/10.12989/sem.2021.79.4.451